@Phaedrux YESSS !! it worked perfectly!!

@Phaedrux Okay i looked up the issue and found YOU lol, going to PID tune the bed. .

@Phaedrux Fixed it and was able to get it heated up to 180,
Now when i try to get the bed heated i get this

Error: Heater 0 fault: temperature rising much more slowly than the expected 1.8°C/sec

@Phaedrux
M308 S1 P"e1temp" Y"thermistor" T98801 B4185 ; configure sensor 1 as thermistor on pin e1temp
M950 H1 C"e1heat" T1 ; create nozzle heater output on e1heat and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit

I think its this line here maybe??
M143 H1 S80 ; set temperature limit for heater 1 to 80C

@fcwilt ok ill try . thanks

@Phaedrux Okay, so ill run another and be sure to save with M500. The M307 generated after the tune isn't saving it anymore?

@Phaedrux
the fault
Heater 0 fault: temperature rising too slowly: expected 2.32°C/sec measured 0.21°C/sec

@Phaedrux @droftarts Good morning From Ms. Thanks for your help first and foremost, having you all a few clicks away has helped me get this far. @Phaedrux Yes i have had some progress. My board wouldn't jump when it was plugged via usb, so i plugged it back to the VIN and did the reset again. This time the diag light kind of blinked once. Unplugged it from there and went back USB and it was found via BOSSA software then flashed the 3.5.3 release. Now I'm back into the DWC this morning, I figure I have to tune everything once again since its been so long. The last time I got this far, my bed heater kept faulting even after the PID tune and programing. At this point i'm im going to put a new thermistor on the bed and do a new test all together just to be sure it's alright down there. I've been following a few threads about it here; https://docs.duet3d.com/User_manual/Troubleshooting/Heater_faults

https://forum.duet3d.com/topic/26122/heater-fault-on-heated-bed-because-it-s-rising-to-slow/54

@Phaedrux hello. My apologies for the late reply. Work has been working lately. I just plugged the board in and went to click show hidden devices and the board still isn't coming up

.

Ive followed instructions thoroughly from my last time trying to find out what went wrong in the process. Im took some time because i felt that things were constantly reaching a dead end. Id really appreciate the help and patience. My computers com ports all work perfectly fine,"yes" I did test and check them. There aren't any programs running in the background, I've checked task manager as well as made sure there were no startup programs running. My poor little board still will not read when plugged in. My computer doesn't even make the initial USB plug in sound. Here is the first troubleshooting thread below. If needed i can Facetime or google video. I really need to get this board up and running duet family. Ive been staring at it staring back at me since this last post.

Re: Board not responding after firmware update DIAG light stays on

@droftarts okay. will do. Thank you.

@droftarts Still nothing happens when i plug it in. i cant find it under the com ports at all. i don't even get the notification of it being plugged in and I've tried all ports. It all dropped once i updated the firmware. I was firmware 3.3 before the update. it finished completely and i restarted it and it hasn't connected since.

@droftarts I took the jumper off and pressed the reset and it still isnt showing up within windows at all.

@droftarts Okay. Thank you for the fast response. I'm about to go and try it now since I have you.

@droftarts "Remove the erase jumper once the Diag LED lights up." So am I to use tweezers and pull the erase jumper off entirely? I am SCAREDDD to hurt my board.