duet3d sd not detected, rejects http, com5 denied
-
@radcad said in duet3d sd not detected, rejects http, com5 denied:
now its saying connections timed out, and YAT is back to saying com5 error
Does Windows Device Manager -> Ports show the Duet?
btw you should set the YAT terminal settings to Line ending: LF only.
Duet WiFi hardware designer and firmware engineer
Please do not ask me for Duet support via PM or email, use the forum
http://www.escher3d.com, https://miscsolutions.wordpress.com -
@dc42
Im not sure how to do that with YAT i am brand new to all this.The duet is showing in device manager.
-
Set YAT to use <LF> as the end of line character. This will improve the readability of the messages coming from the Duet. Click "Text Settings" in the "Terminal Settings" and change "EOL sequence:" to <LF>. Click "OK" to close Text Settings. Click "OK" again to close Terminal Settings.
-
Thank you ok that is now changed. still not connecting tho.
I notice when i re open the settings it reverts back to saying <cl><lf>
-
Would it be better to power on the printer power supply and try to do all this wirelessly or keep working through the USB
-
Well if things are working to the point where you can connect to the web interface than what exactly is still the problem?
-
@Phaedrux it is not connecting currently. i didnt know if the 24 volt for the printer did anything important. and ive read about some ground loop situation happening through USB but i dont really understand what they ment.
-
USB power is enough for testing.
Can you show a screen shot of your SD card folders and files?
Did you replace the contents of the /www folder with the file I linked?
When connected with YAT what happens when you send M552?
-
@Phaedrux
what file type does the image need to be? i tried uploading bmp and jpeg both failed.I cannot get YAT to connect com port 5 busy
I followed your instructions best that I could understand, everything should be in the right place.
It did connect again after I did what you said, after disconnect it would not reconnect. -
Tried changing the port still same result.
-
Maybe it would be best to start from the top.
https://duet3d.dozuki.com/Guide/1.)+Getting+Connected+to+your+Duet/7
-
@Phaedrux
for firmware update is this the file i need from the gethub
Duet2and3Firmware-3.2.zip -
Only update the firmware if you've got a reliable connection to the web interface now.
If you still have access to DWC. Upload these 3 zip files, one at a time. Don't extract them. Reboot after each. Use M115 to verify the firmware has been applied.
https://github.com/Duet3D/RepRapFirmware/releases/download/2.05.1/Duet2Firmware-2.05.1.zip
https://github.com/Duet3D/RepRapFirmware/releases/download/3.0/Duet2and3Firmware-3.0.zip
https://github.com/Duet3D/RepRapFirmware/releases/download/3.2/Duet2and3Firmware-3.2.zip
That will get your firmware and DWC up to date.For your config, might be a good idea to run through the configurator tool and generate a fresh set for RRF3.
https://configtool.reprapfirmware.org/Start -
@Phaedrux
YAT and web interface are connected -
@Phaedrux
so i put these files on the sd card then run the M commands ? -
No. Upload them to the system tab in the web interface. One zip file at a time. Start with 2.05.1. It will prompt you to update. And reboot.
-
@Phaedrux
Failed to upload network error
M552 S1 say wifi is ok -
And you're trying to upload it to the system tab?
Can you go to the console tab and send M122 and copy and paste the results?
-
This post is deleted! -
In the system tab you'd find your config.g and the homing files, etc.
That's where you would upload Duet2Firmware-2.05.1.zip
