duet3d sd not detected, rejects http, com5 denied

Phaedrux

USB power is enough for testing.

Can you show a screen shot of your SD card folders and files?

Did you replace the contents of the /www folder with the file I linked?

When connected with YAT what happens when you send M552?

radcad

@Phaedrux
what file type does the image need to be? i tried uploading bmp and jpeg both failed.

I cannot get YAT to connect com port 5 busy

I followed your instructions best that I could understand, everything should be in the right place.
It did connect again after I did what you said, after disconnect it would not reconnect.

radcad

Tried changing the port still same result.

Phaedrux

Maybe it would be best to start from the top.

https://duet3d.dozuki.com/Guide/1.)+Getting+Connected+to+your+Duet/7

radcad

@Phaedrux
for firmware update is this the file i need from the gethub
Duet2and3Firmware-3.2.zip

Phaedrux

Only update the firmware if you've got a reliable connection to the web interface now.

If you still have access to DWC. Upload these 3 zip files, one at a time. Don't extract them. Reboot after each. Use M115 to verify the firmware has been applied.
https://github.com/Duet3D/RepRapFirmware/releases/download/2.05.1/Duet2Firmware-2.05.1.zip
https://github.com/Duet3D/RepRapFirmware/releases/download/3.0/Duet2and3Firmware-3.0.zip
https://github.com/Duet3D/RepRapFirmware/releases/download/3.2/Duet2and3Firmware-3.2.zip
That will get your firmware and DWC up to date.

For your config, might be a good idea to run through the configurator tool and generate a fresh set for RRF3.
https://configtool.reprapfirmware.org/Start

radcad

@Phaedrux
YAT and web interface are connected

radcad

@Phaedrux
so i put these files on the sd card then run the M commands ?

Phaedrux

No. Upload them to the system tab in the web interface. One zip file at a time. Start with 2.05.1. It will prompt you to update. And reboot.

radcad

@Phaedrux
Failed to upload network error
M552 S1 say wifi is ok

Phaedrux

And you're trying to upload it to the system tab?

Can you go to the console tab and send M122 and copy and paste the results?

radcad

This post is deleted!

Phaedrux

In the system tab you'd find your config.g and the homing files, etc.

That's where you would upload Duet2Firmware-2.05.1.zip

radcad

@Phaedrux
yes in the system tab under file management on the left, is where I tried to upload it, the file does not show up in other tabs

Phaedrux

And you're using the upload file button?

Can you post a screen shot of the error?

radcad

@Phaedrux
what file format do i need to save the screen shot as to upload it here?

Phaedrux

If you're on windows you can use the print screen button on your keyboard and paste that into paint and save it as a jpeg.

radcad

radcad

I kept retrying it over and over and eventually it uploaded.
trying to get the 2nd file to load now. it wont get past the 4th file tho

WiFi module is connected to access point 111111 IP address 11111111
Trying to connect at 230400 baud: success
Erasing 4096 bytes...
Erasing 212992 bytes...
Uploading file...
5% complete
10% complete
15% complete
20% complete
25% complete
30% complete
35% complete
40% complete
45% complete
50% complete
55% complete
60% complete
65% complete
70% complete
75% complete
80% complete
85% complete
90% complete
95% complete
Upload successful

radcad

2nd file finally uploaded