Dual Markforged :idle IDEX carriage is not still during print

Phaedrux

Can you send M98 P"config.g" and post the results?

Z799.2:799.2:799.2
Remove the duplicate entries for the Z axis. All the linear axis are configured as a single axis. It's only the extruders which remain independent and need to be configured per driver.

M906 Y700 Z700:700:700 E1000:1000 I50
There appears to be an extra space after M906. Not sure it matters.

You can send the motor config commands by themselves to check that they are configured as expected. For instance, sending M906 in the console to see what the motor currents are actually set to.

martin7404

@sebkritikel i tried 100 % idle current, no change

martin7404

@Phaedrux

M98 P"config.g"
HTTP is enabled on port 80
FTP is disabled
TELNET is disabled
Warning: Heater 0 appears to be over-powered. If left on at full power, its temperature is predicted to reach 365C
The M568 command is no longer needed
Warning: Heater 1 appears to be over-powered. If left on at full power, its temperature is predicted to reach 723C
Warning: Heater 2 appears to be over-powered. If left on at full power, its temperature is predicted to reach 528C

martin7404

@Phaedrux ```

m906
Motor current (mA) - X:700, Y:700, Z:500, U:700, E:1000:1000, idle factor 50%
3/8/2021, 11:35:56 PM	M98 P"config.g"

Phaedrux

@martin7404 said in Dual Markforged :idle IDEX carriage is not still during print:

m906

How bout for the other commands? M92 M305 M201 M203 etc etc

martin7404

@Phaedrux

m203
Max speeds (mm/min): X: 12000.0, Y: 12000.0, Z: 1000.0, U: 12000.0, E: 4200.0:4200.0, min. speed 30.00
3/9/2021, 7:12:00 AM	m201
Accelerations (mm/sec^2): X: 800.0, Y: 800.0, Z: 350.0, U: 800.0, E: 600.0:600.0
3/9/2021, 7:11:43 AM	m950
Error: M950: exactly one of FHJPS must be given
3/9/2021, 7:11:32 AM	m308
Error: M308: missing parameter 'S'
3/9/2021, 7:11:21 AM	m305
Error: M305: M305 has been replaced by M308 and M950 in RepRapFirmware 3
3/9/2021, 7:05:16 AM	m92
Steps/mm: X: 100.000, Y: 100.000, Z: 799.200, U: 100.000, E: 813.070:830.000
3/9/2021, 7:03:45 AM	Connection established

martin7404

I have a solution of the problem by chance.
I am still waiting for my new Duet wifi , and the setup is the strange one with Z on duet and X,y and U on Duex.
Because the machine is working somehow I continued with the commissioning I started Dual material print with both tools and in the begining of gcode both tools are defined temps with G10 and then with Tn P0 , both are activated for a moment in order to reach standby temp. Then G28 G29 etc....
It happens that when both tools are activated and the idle is on standby there is no movement in stanby tool

martin7404

My new duet wifi is here , installed, updated firmware to 3.2.2, X,Y,U axes are back on mainboard, first print ongoing

martin7404

So it is printing with U carriage at the moment an the X carriage that is standby is dead still during print

dc42

@martin7404 said in Dual Markforged :idle IDEX carriage is not still during print:

So it is printing with U carriage at the moment an the X carriage that is standby is dead still during print

Assuming you home both carriages before doing a print, then both motors should have current flowing in them, unless you subsequently use M18 or M84 to set one or more motors idle.

martin7404

@dc42 in the start G code there is always homing X U Y Z. But when I enable only Left or Right extruder with G10 in the beginning, during print the tool that was not active was moving a little back and forth with Y-axis changing direction.
Then I found a faulty mainboard
......
The whole time there was no unactivated axis motor

So I think it is now sorted with new mainboard