• Tags
  • Documentation
  • Order
  • Register
  • Login
Duet3D Logo Duet3D
  • Tags
  • Documentation
  • Order
  • Register
  • Login

Autotune failed

Scheduled Pinned Locked Moved
General Discussion
4
11
689
Loading More Posts
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • undefined
    norwestie
    last edited by 30 May 2021, 20:03

    I ran M303 T0 S205 and got this result:
    5/30/2021, 12:58:36 PM Warning: Auto tune of heater 1 failed due to bad curve fit (R=2.813, 1/C=0.0094:0.0094, D=7.0)
    5/30/2021, 12:55:23 PM Auto tune starting phase 5, tuning with fan on
    5/30/2021, 12:52:48 PM Auto tune starting phase 4, tuning with fan off
    5/30/2021, 12:50:27 PM Auto tune starting phase 3, heating system settling
    5/30/2021, 12:49:22 PM Auto tune starting phase 1, heater on
    5/30/2021, 12:49:17 PM M303 T0 S205 ; tune the primary heater of tool 0
    Auto tuning heater 1 using target temperature 205.0°C and PWM 1.00 - do not leave printer unattended

    This is the heater setup in config.g:
    Heaters
    M308 S0 P"temp0" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin temp0
    M950 H0 C"out0" T0 ; create bed heater output on out0 and map it to sensor 0
    M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
    M140 H0 ; map heated bed to heater 0
    M143 H0 S120 ; set temperature limit for heater 0 to 120C
    M308 S1 P"temp1" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin temp1
    M950 H1 C"out1" T1 ; create nozzle heater output on out1 and map it to sensor 1
    M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
    M143 H1 S280 ; set temperature limit for heater 1 to 280C

    Anycubic Kossel Linear Plus
    Duet Mini 5+ Ethernet
    Firmware 3.3RC2

    undefined 1 Reply Last reply 31 May 2021, 08:44 Reply Quote 0
    • undefined
      Phaedrux Moderator
      last edited by 30 May 2021, 22:21

      Can you give some more info about the heater setup? Maybe a photo?
      What did the temp graph look like during tuning?
      Firmware version? Duet mini?
      Psu voltage? Heater wattage?
      Is the fan blowing on the heater block?

      Z-Bot CoreXY Build | Thingiverse Profile

      undefined 1 Reply Last reply 30 May 2021, 23:40 Reply Quote 0
      • undefined
        norwestie @Phaedrux
        last edited by 30 May 2021, 23:40

        @phaedrux The graph was an even zigzag until the end of the 5th phase. Firmware is 3.3. Power supply is Meanwell 350 watt 12v. I think the wattage is 40w

        Anycubic Kossel Linear Plus
        Duet Mini 5+ Ethernet
        Firmware 3.3RC2

        1 Reply Last reply Reply Quote 0
        • undefined
          Phaedrux Moderator
          last edited by 31 May 2021, 03:12

          A photo of the hotend assembly and a photo of the temp graph would help a lot in understanding why it might be giving a bad curve fit. Basically it means it's not heating or cooling at the rate the model predicts. Could be the cooling fan is blowing too much on the hot block, or the hot block is making contact with the cold end heatsink. Do you have a nozzle sock installed?

          Z-Bot CoreXY Build | Thingiverse Profile

          1 Reply Last reply Reply Quote 0
          • undefined
            huskypsyd
            last edited by 31 May 2021, 03:49

            Same issue here. Worked fine in v3.2. 3.3 is causing me an issue now.
            5/30/2021, 8:33:29 PM Warning: Auto tune of heater 1 failed due to bad curve fit (R=2.783, 1/C=0.0075:0.0074, D=4.9)
            5/30/2021, 8:30:56 PM Auto tune starting phase 5, tuning with fan on
            5/30/2021, 8:28:54 PM Auto tune starting phase 4, tuning with fan off
            5/30/2021, 8:26:58 PM Auto tune starting phase 3, heating system settling
            5/30/2021, 8:26:12 PM Auto tune starting phase 1, heater on
            5/30/2021, 8:26:06 PM M303 T0 S205
            Auto tuning heater 1 using target temperature 205.0°C and PWM 1.00 - do not leave printer unattended

            ; Heaters
            M308 S0 P"temp0" Y"thermistor" T100000 B3950 ; configure sensor 0 as thermistor on pin temp0
            M950 H0 C"out0" T0 ; create bed heater output on out0 and map it to sensor 0
            M307 H0 R0.447 C328.1 D1.77 V24.1 S1 B0 ; disable bang-bang mode for the bed heater and set PWM limit
            M140 H0 ; map heated bed to heater 0
            M143 H0 S150 ; set temperature limit for heater 0 to 150C
            M308 S1 P"temp1" Y"thermistor" T100000 B4267 ; configure sensor 1 as thermistor on pin temp1
            M950 H1 C"out1" T1 ; create nozzle heater output on out1 and map it to sensor 1
            M307 H1 R2.656 C131.0:130.9 D5.81 S1.00 V24.2 B0 ; disable bang-bang mode for heater and set PWM limit
            M143 H1 S300 ; set temperature limit for heater 1 to 300C

            undefined undefined 2 Replies Last reply 31 May 2021, 04:23 Reply Quote 0
            • undefined
              huskypsyd @huskypsyd
              last edited by 31 May 2021, 04:23

              @huskypsyd Firmware 3.3RC3

              1 Reply Last reply Reply Quote 0
              • undefined
                dc42 administrators @norwestie
                last edited by 31 May 2021, 08:44

                @norwestie my best guess is that you don't have the print cooling fan configured correctly, so the cooling rate with fan on was measured to be slightly less than with fan on (whereas it should be higher).

                If that is not correct, and the print cooling fan really doesn't have any significant effect on the hot end temperature, then I suggest you re-run heater tuning with parameter H1 instead of T0 in the M303 command. Alternatively, use these parameters:

                M307 H1 R2.813 C106.4 D7.0

                106.4 is the reciprocal of the value 0.0094 that was reported in the message.

                Duet WiFi hardware designer and firmware engineer
                Please do not ask me for Duet support via PM or email, use the forum
                http://www.escher3d.com, https://miscsolutions.wordpress.com

                undefined 1 Reply Last reply 31 May 2021, 17:31 Reply Quote 0
                • undefined
                  dc42 administrators @huskypsyd
                  last edited by 31 May 2021, 08:46

                  @huskypsyd the reason is the same as in my previous reply, except that in this case we can see that the measured cooling rate with fan on is lower than fan off, 0.0074 instead of 0.0075.

                  Duet WiFi hardware designer and firmware engineer
                  Please do not ask me for Duet support via PM or email, use the forum
                  http://www.escher3d.com, https://miscsolutions.wordpress.com

                  undefined 1 Reply Last reply 31 May 2021, 08:55 Reply Quote 0
                  • undefined
                    huskypsyd @dc42
                    last edited by 31 May 2021, 08:55

                    @dc42 thank you!

                    1 Reply Last reply Reply Quote 0
                    • undefined
                      norwestie @dc42
                      last edited by 31 May 2021, 17:31

                      @dc42 said in Autotune failed:

                      M307 H1 R2.813 C106.4 D7.0

                      The H1 substitution worked! Thank you. Onward to my next error ¯_(ツ)_/¯
                      IMG_3581.JPG Screen Shot 2021-05-31 at 10.28.02 AM.png

                      Anycubic Kossel Linear Plus
                      Duet Mini 5+ Ethernet
                      Firmware 3.3RC2

                      undefined 1 Reply Last reply 20 Jun 2021, 18:09 Reply Quote 0
                      • undefined
                        dc42 administrators @norwestie
                        last edited by 20 Jun 2021, 18:09

                        @norwestie this issue is fixed in RRF 3.3.

                        Duet WiFi hardware designer and firmware engineer
                        Please do not ask me for Duet support via PM or email, use the forum
                        http://www.escher3d.com, https://miscsolutions.wordpress.com

                        1 Reply Last reply Reply Quote 0
                        • First post
                          Last post
                        Unless otherwise noted, all forum content is licensed under CC-BY-SA