Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    I could use some help

    Scheduled Pinned Locked Moved
    Duet Hardware and wiring
    11
    682
    54.5k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • A Former User?
      A Former User @fcwilt
      last edited by

      @fcwilt wait, fcwilt? not droftarts? jeeze you guys are ganging up on me!

      A Former User? fcwiltundefined 2 Replies Last reply Reply Quote 0
      • fcwiltundefined
        fcwilt @A Former User
        last edited by

        @mac said in I could use some help:

        @fcwilt the only thing that would close the z endstop is if the X axis came down and closed it.

        OK that's good to know.

        If the white wire is actually connected to the NO connection of the Z endstop switch it should not be indicating Z at min stop.

        Find a way to close the Z endstop switch and execute M119.

        I want to see if it still reports Z at min stop or if it reports something different.

        Frederick

        Printers: A FT-5 with the 713 upgrade bits, a custom MarkForged style, a small Utilmaker style, a small CoreXY from kit and a E3D MS/TC setup. Various hotends. Using Duets (2 and 3) running 3.4.6

        A Former User? 1 Reply Last reply Reply Quote 0
        • A Former User?
          A Former User @A Former User
          last edited by

          @droftarts @fcwilt if we're going to work on this together, I need to know you two are in agreement before I do anything.

          Do you both agree that I should tape X and Y closed? Then M119 again?

          fcwiltundefined droftartsundefined 2 Replies Last reply Reply Quote 0
          • fcwiltundefined
            fcwilt @A Former User
            last edited by

            @mac said in I could use some help:

            @fcwilt wait, fcwilt? not droftarts? jeeze you guys are ganging up on me!

            No - it just gets confusing when posts overlap in time.

            I'm typing, your typing, droftarts is typing - and things get a bit out of order - time wise.

            Frederick

            Printers: A FT-5 with the 713 upgrade bits, a custom MarkForged style, a small Utilmaker style, a small CoreXY from kit and a E3D MS/TC setup. Various hotends. Using Duets (2 and 3) running 3.4.6

            1 Reply Last reply Reply Quote 0
            • fcwiltundefined
              fcwilt @A Former User
              last edited by

              @mac said in I could use some help:

              @droftarts @fcwilt if we're going to work on this together, I need to know you two are in agreement before I do anything.

              Do you both agree that I should tape X and Y closed? Then M119 again?

              Mac! You've cut me to the quick! Have you no faith in me! 😉

              I've only been doing this stuff for years.

              Frederick

              Printers: A FT-5 with the 713 upgrade bits, a custom MarkForged style, a small Utilmaker style, a small CoreXY from kit and a E3D MS/TC setup. Various hotends. Using Duets (2 and 3) running 3.4.6

              A Former User? 1 Reply Last reply Reply Quote 0
              • A Former User?
                A Former User @fcwilt
                last edited by

                @fcwilt @droftarts I closed the z-endstop with my left finger, and hit M110 Send with my right finger. M119 reported Z: at end stop, Z probe: not stopped.

                I'm not making this up, guys.

                fcwiltundefined 1 Reply Last reply Reply Quote 0
                • A Former User?
                  A Former User @fcwilt
                  last edited by

                  @fcwilt @droftarts I'm just trying to be respectful to Ian and you.

                  1 Reply Last reply Reply Quote 1
                  • droftartsundefined
                    droftarts administrators @A Former User
                    last edited by

                    @mac I’m not able to reply promptly now, I’m away from my computer. @fcwilt knows what he’s doing, though please keep it simple, Frederick!

                    Ian

                    TronXY X5S with Duet 3 MB6HC and Roto toolboard : Cartesian bed-slinger with Duet 3 Mini 5+ WiFi and 1LC : RRP Fisher Delta v1 with Duet 2 Maestro : Polargraph with Duet 2 WiFi

                    fcwiltundefined 1 Reply Last reply Reply Quote 0
                    • fcwiltundefined
                      fcwilt @droftarts
                      last edited by

                      @droftarts said in I could use some help:

                      @mac I’m not able to reply promptly now, I’m away from my computer. @fcwilt knows what he’s doing, though please keep it simple, Frederick!

                      Ian

                      I try to keep it simple, I really do.

                      Frederick

                      Printers: A FT-5 with the 713 upgrade bits, a custom MarkForged style, a small Utilmaker style, a small CoreXY from kit and a E3D MS/TC setup. Various hotends. Using Duets (2 and 3) running 3.4.6

                      A Former User? 1 Reply Last reply Reply Quote 0
                      • A Former User?
                        A Former User @fcwilt
                        last edited by

                        @fcwilt @droftarts

                        ; Drives
M569 P0.0 S1                                       ; physical drive 0.0 goes forwards
M569 P0.1 S1                                       ; physical drive 0.1 goes forwards
M569 P0.2 S1                                       ; physical drive 0.2 goes forwards
M569 P0.3 S1                                       ; physical drive 0.3 goes forwards
M584 X0.0 Y0.1 Z0.2 E0.3                           ; set drive mapping
M92 X40.00 Y40.00 Z2000.00 E420.00                 ; set steps per mm
M350 X16 Y16 Z16 E16 I1                            ; configure microstepping with interpolation
M566 X900.00 Y900.00 Z60.00 E120.00                ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z600.00 E1200.00            ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z200.00 E250.00               ; set accelerations (mm/s^2)
M906 X600 Y600 Z600 E600                           ; set motor currents (mA)
M84 S0                                             ; Disable motor idle current reduction
                        A Former User? 1 Reply Last reply Reply Quote 0
                        • A Former User?
                          A Former User @A Former User
                          last edited by A Former User

                          @mac M92 cut and pasted to before M350, board rebooted.

                          A Former User? 1 Reply Last reply Reply Quote 0
                          • A Former User?
                            A Former User @A Former User
                            last edited by

                            @fcwilt okay, I get it, let's continue on, shall we, Frederick?

                            1 Reply Last reply Reply Quote 1
                            • fcwiltundefined
                              fcwilt @A Former User
                              last edited by

                              @mac said in I could use some help:

                              @fcwilt @droftarts I closed the z-endstop with my left finger, and hit M110 Send with my right finger. M119 reported Z: at end stop, Z probe: not stopped.

                              I'm not making this up, guys.

                              I know you are not. I have complete faith in you.

                              So as far as you can see M119 reports that same for the Z endstop switch regardless of it being pressed closed or not?

                              Interesting.

                              How about doing the same for the X and Y endstop switches. You can press just one at a time and execute the M119 for each one. It is not necessary to press them both at the same time.

                              What we want to verify is that M119 reports the correct thing for both states of the endstop switches, pressed and not pressed.

                              Frederick

                              Printers: A FT-5 with the 713 upgrade bits, a custom MarkForged style, a small Utilmaker style, a small CoreXY from kit and a E3D MS/TC setup. Various hotends. Using Duets (2 and 3) running 3.4.6

                              A Former User? 1 Reply Last reply Reply Quote 0
                              • A Former User?
                                A Former User @fcwilt
                                last edited by

                                @fcwilt I just ran M119 again, it's reporting: X not stopped, Y not stopped, Z at min stop, Z probe not stopped.

                                A Former User? fcwiltundefined 2 Replies Last reply Reply Quote 0
                                • A Former User?
                                  A Former User @A Former User
                                  last edited by

                                  @fcwilt I just verified that with the z-endstop pushed down, M119 is reporting the same information as above.

                                  1 Reply Last reply Reply Quote 0
                                  • fcwiltundefined
                                    fcwilt @A Former User
                                    last edited by

                                    @mac said in I could use some help:

                                    @fcwilt I just ran M119 again, it's reporting: X not stopped, Y not stopped, Z at min stop, Z probe not stopped.

                                    OK let's leave Z for now and test X and Y.

                                    Frederick

                                    Printers: A FT-5 with the 713 upgrade bits, a custom MarkForged style, a small Utilmaker style, a small CoreXY from kit and a E3D MS/TC setup. Various hotends. Using Duets (2 and 3) running 3.4.6

                                    A Former User? 1 Reply Last reply Reply Quote 0
                                    • A Former User?
                                      A Former User @fcwilt
                                      last edited by

                                      @fcwilt I'm going to test the X endstop, and then the Y endstop. Please wait for my report.

                                      fcwiltundefined A Former User? 2 Replies Last reply Reply Quote 0
                                      • fcwiltundefined
                                        fcwilt @A Former User
                                        last edited by

                                        @mac

                                        I'm not going anywhere.

                                        Frederick

                                        Printers: A FT-5 with the 713 upgrade bits, a custom MarkForged style, a small Utilmaker style, a small CoreXY from kit and a E3D MS/TC setup. Various hotends. Using Duets (2 and 3) running 3.4.6

                                        1 Reply Last reply Reply Quote 0
                                        • A Former User?
                                          A Former User @A Former User
                                          last edited by

                                          @fcwilt okay, here are the results: with X endstop pressed down, M119 reports X at min stop. With Y endstop pressed down, M119 reports Y at min stop.

                                          Interestingly, M119 continues to report Z at min stop even though I'm NOT pressing it down?

                                          A Former User? 1 Reply Last reply Reply Quote 0
                                          • A Former User?
                                            A Former User @A Former User
                                            last edited by

                                            @fcwilt

                                            ; Axis Limits
M208 X0 Y0 Z0 S1                                   ; set axis minima
M208 X220 Y220 Z240 S0                             ; set axis maxima
                                            A Former User? 1 Reply Last reply Reply Quote 0
                                            • First post
                                              Last post
                                            Unless otherwise noted, all forum content is licensed under CC-BY-SA