DUET 2 Wifi, DIAG Led is constantly ON, no respond from terminal

[jay_s_uk]

@droftarts is this added to the instructions? might be worth it under the mac section if not

[droftarts]

@jay_s_uk It is mentioned, but very briefly. I'll update it with a note for M1 and M2 Macs, and update my post here: https://forum.duet3d.com/post/103234

As far as I'm aware, no macOS version of bossa/bossac will flash the Duet 3 mainboard 6HC (and probably not the 6XD as well), including the @MartinNYHC version. @chrishamm has been looking at it, but hasn't worked out why.

Ian

[darkcolman]

@droftarts @jay_s_uk it works ! the duet 2 is back ! Big thanks for that !
I can talk with the board through Pronterface ! But I still have some issues ...

So I have sent an M115 and the firmware 3.4.1 seems to be in the duet.
So I have followed the back procedure number 1.
I have sent a M997 S0 and M997 S1 and the app can't find the file on the SD card ...

I have tried different types of name of subfile ( all the bin files are in each subfolder ) but the app can't find any bin file ...
What have I done wrong again ?

Thank you

Jeff

[jay_s_uk]

@darkcolman the DuetWifiServer.bin file needs to be in the firmware folder (no leading /)

[darkcolman]

@jay_s_uk I have already Done this

[darkcolman]

@jay_s_uk I have also change the name of the sd card "0" after to receive the message from pronterface. Before the SD card named "WORKBEE"

[jay_s_uk]

@darkcolman you're on 3.4.1 so theres no need to send M997 S0 (as that updates the mainboard firmware, which is already up to date) you just need M997 S1.

you also don't need to change the name of the SD card. 0:/ is the name internally used by RRF to identify the sd card slot in the board

[darkcolman]

@jay_s_uk on the picture, I've done as well the command M997 S1. the file is not found easer. And it's been placed in the good subflle at the beginning with the correct name

[jay_s_uk]

@darkcolman what format is the SD card?

[darkcolman]

@jay_s_uk FAT 32

[jay_s_uk]

@darkcolman post an output of M122

[darkcolman]

@jay_s_uk

[darkcolman]

@jay_s_uk weird, the SD card seems not detected ...
I can say that when it's fully inserted, I can hear a faint click and when I push again, it release the SD card.
and all pins seems okay to me

[jay_s_uk]

@darkcolman that was my guess that the sd card wasn't being detected. I would reformat the sd card using the sd card formatter and start again https://www.sdcard.org/downloads/formatter/
or try another sd card
if that doesn't work, try M39 and see what it reports

[Phaedrux]

If the steps provided by Jay don't get it working there may be a problem with the SD card slot. Could you provide some close up photos of the slot and it's soldering?

[darkcolman]

@phaedrux @jay_s_uk actually it works ! thanks a lot for that !
M997 S1 has been a success

[jay_s_uk]

@darkcolman how did you fix it?

[darkcolman]

@jay_s_uk I've followed your advice and I've formatted the SD Card from Formatter software and it worked perfectly.

But Now I've another issue....
I can't connect the duet to the wifi to set it up.

the link that I've followed :

https://docs.duet3d.com/How_to_guides/Getting_connected/Getting_connected_to_your_Duet

And this is what I've done

I can't or maybe I don't understand how to Configure network SSID and password.
What I've missed ?

[jay_s_uk]

@darkcolman don't use pronterface. It converts all text to uppercase. You can faff on adding a ' in front of each lowercase letter but it's better just to use putty or YAT

[Phaedrux]

For MacOS your best bet is probably SerialTools

https://docs.duet3d.com/How_to_guides/Getting_connected/Getting_connected_to_your_Duet#h-3-connect-to-duet