Suddenly extrusion buttons Extrude/Retract are grey!

tecno

Can not get E0 to extrude, M302 P1 = still grey buttons

Rushmere3D

@tecno Do you have a tool selected?

tecno

@rushmere3d
As far as I can tell Yes

deckingman

@tecno I don't know if it will make any difference but try using upper case instead of lower case. i.e. M302 P1 then hit send, rather than m302 p1.

jay_s_uk

@tecno what version of RRF and DWC are you using?

Rushmere3D

@tecno Why is your tool T1 and not T0?

tecno

@jay_s_uk

tecno

@rushmere3d

Old habit, all my printers have T1

jay_s_uk

@tecno can't remember if there were any bugs back with 3.3.0. Best update to 3.4.1

tecno

NOT ~~SOLVED~~

Error in writing config.g so I took an older one and edited necessary lines.
Got M302 P1 working and then lost connection and now I can not reach the printer.

tecno

I have now updated DCW to 3.4.1 = still no M302 P1

Only TOOLS section was edited before all this with no filament feed occured.
https://forum.duet3d.com/topic/29618/superslicer-question/5

; Configuration file for Fly-E3 (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.3.1-LPC-STM32+7 on Mon Mar 14 2022 20:23:48 GMT+0100 (centraleuropeisk normaltid)

; General preferences
G90                                            ; send absolute coordinates...
M83                                            ; ...but relative extruder moves
M550 P"VORON"                                  ; set printer name
M669 K1                                        ; select CoreXY mode
M564 H0

; Network
M551 P"     "                                  ; set password
M552 S1                                        ; enable network
M586 P0 S1                                     ; enable HTTP
M586 P1 S0                                     ; disable FTP
M586 P2 S0                                     ; disable Telnet


; Drives
M569 P0 S1                                     ; physical drive 0 goes forwards using default driver timings
M569 P1 S1                                     ; physical drive 1 goes forwards using default driver timings
M569 P2 S1                                     ; physical drive 2 goes forwards using default driver timings
M569 P3 S1									   ; physical drive 3 goes forwards using default driver timings
M584 X0 Y1 Z2 E3                               ; set drive mapping
M350 X16 Y16 Z16 E16 I1                        ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z400.00 E690.00              ; set steps per mm z400
M572 D0 S0.10								   ; PA
M566 X100.00 Y100.00 Z100.00 E600.00           ; set maximum instantaneous speed changes (mm/min)
M203 X5000.00 Y5000.00 Z2600.00 E7200.00       ; set maximum speeds (mm/min)
M201 X1500.00 Y1500.00 Z1500.00 E800.00        ; set accelerations (mm/s^2)
M906 X1250 Y1250 Z400 E800 I25   			   ; set motor currents (mA) and motor idle factor in per cent
M207 S1.5 F7200 Z0.2 						   ;firmware retraction

M84 S30                                        ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z-3 S1                                ; set axis minima
M208 X120 Y100 Z110 S0                          ; set axis maxima

; Endstops
M574 X2 S1 P"xstop"                            ; configure active-high endstop for low end on X via pin xstop
M574 Y2 S1 P"ystop"                            ; configure active-high endstop for low end on Y via pin ystop
M574 Z2 S1 P"zstop"                            ; configure active-high endstop for low end on Z via pin zstop


Z-Probe
M558 P0 H5 T6000 F1500:250 ;A5 ;S.25    ; 
;G31 P1000 X0 Y20 Z1.7
M557 X20:120 Y20:110 S30                       ; define mesh grid



; Heaters
M308 S0 A"Bed" P"bedtemp" Y"thermistor" T100000 B4092 		; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bed" T0                              				; create bed heater output on bed and map it to sensor 0
M307 H0 B0 R1.109 C133.4 D4.22 S1.00 V0.0     				; disable bang-bang mode for the bed heater and set PWM limit
M140 H0                                        				; map heated bed to heater 0
M143 H0 S120                                   				; set temperature limit for heater 0 to 120C
M308 S1 A"Nozzle" P"e0temp" Y"thermistor" T100000 B4092  	; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1                          				; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 R2.424 C165.6 D6.10 S1.00 V0.0      				; disable bang-bang mode for heater  and set PWM limit
M143 H1 S280                                   				; set temperature limit for heater 1 to 280C


; Fans
M950 F0 C"fan0"                                ; // PART FAN
M106 P0 S0 H-1								   ; P0 = fan0 S0 = Speed 0 H-1 = Disable Termostatic mode

M950 F1 C"fan1" 		                       ; // TOOL FAN
M106 P1 S1								       ; P1 = fan1 S1 = Speed 100% 

; Tools
M563 P1 H1 F0                                  ; P1 = tool1 H1 = heater1 F1 = fan1
G10 P1 X0 Y0 Z0                                ; set tool 0 axis offsets
G10 P1 R0 S0                                   ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
T1                                             ; select first tool

jay_s_uk

@tecno have you updated the firmware too?
try switching to tool 0

tecno

@jay_s_uk
No, will do
What lines in config needs to be changed for T0

jay_s_uk

@tecno said in Suddenly extrusion buttons Extrude/Retract are grey!:

; Tools
M563 P1 H1 F0 ; P1 = tool1 H1 = heater1 F1 = fan1
G10 P1 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P1 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
T1 ; select first tool

change those to these

; Tools
M563 P0 H1 F0                                  ; P1 = tool1 H1 = heater1 F1 = fan1
G10 P0 X0 Y0 Z0                                ; set tool 0 axis offsets
G10 P0 R0 S0                                   ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
T0

tecno

@jay_s_uk

OK, done that. But still no M302 P1 = all gray buttons

tecno

Updated FW = still same error

deckingman

@tecno said in Suddenly extrusion buttons Extrude/Retract are grey!:

@jay_s_uk

OK, done that. But still no M302 P1 = all gray buttons

~~If you've changed the tool from T1 to T0, then you need to use M302 P0 not M302 P1.~~

Edit. Ignore that crap. Next time I'll try and engage my brain before typing.....

jay_s_uk

@deckingman i thought M302 was system wide? https://docs.duet3d.com/en/User_manual/Reference/Gcodes#m302-allow-cold-extrudes
P1 = allow, P0 = not allow?

tecno

@deckingman said in Suddenly extrusion buttons Extrude/Retract are grey!:

@tecno said in Suddenly extrusion buttons Extrude/Retract are grey!:

@jay_s_uk

OK, done that. But still no M302 P1 = all gray buttons

If you've changed the tool from T1 to T0, then you need to use M302 P0 not M302 P1.

2022-08-18 12:57:49	M302
Cold extrusion is forbidden (use M302 P1 to allow it), min. extrusion temperature 160.0C, min. retraction temperature 90.0C
2022-08-18 12:57:39	M302 P0

deckingman

@jay_s_uk said in Suddenly extrusion buttons Extrude/Retract are grey!:

@deckingman i thought M302 was system wide? https://docs.duet3d.com/en/User_manual/Reference/Gcodes#m302-allow-cold-extrudes
P1 = allow, P0 = not allow?

Oh crap - you are right of course - more caffeine needed