z probe not referenced

[axiom]

@jay_s_uk

ah there is another message:
"G28
Error: Failed to enable endstops"

[axiom]

@jay_s_uk
the button "Home all"

[jay_s_uk]

@axiom then post the contents of your homeall.g file

[axiom]

@jay_s_uk
this is a standard feature that came with the dashboard... where can i find the content?

[jay_s_uk]

@axiom on the system tab on the left hand side

[axiom]

@axiom ; homeall.g
; called to home all axes
;
; generated by RepRapFirmware Configuration Tool v3.3.12 on Wed Aug 24 2022 12:56:11 GMT+0200 (Mitteleuropäische Sommerzeit)
G91 ; relative positioning
G1 H2 Z5 F6000 ; lift Z relative to current position
G1 H1 X-505 Y-505 F1800 ; move quickly to X and Y axis endstops and stop there (first pass)
G1 H2 X5 Y5 F6000 ; go back a few mm
G1 H1 X-505 Y-505 F360 ; move slowly to X and Y axis endstops once more (second pass)
G1 H1 Z705 F360 ; move Z up stopping at the endstop
G90 ; absolute positioning
G92 Z700 ; set Z position to axis maximum (you may want to adjust this)

; Uncomment the following lines to lift Z after probing
;G91 ; relative positioning
;G1 Z5 F100 ; lift Z relative to current position
;G90 ; absolute positioning

[jay_s_uk]

@axiom said in z probe not referenced:

G1 H1 Z705 F360 ; move Z up stopping at the endstop
G90 ; absolute positioning
G92 Z700 ; set Z position to axis maximum (you may want to adjust this)

you're trying to home using an endstop.
To home with a probe you need to move to the position you want to probe, usually the middle of the bed and then use G30
E.g.

G1 X150 Y150
G30

[axiom]

@jay_s_uk
I commented out lines 6 and 10 and added lines 11 and 12.
Now the message appears: "G28 Error: Probe already triggered at start of probinge move

here the new code:
; homeall.g
; called to home all axes
;
; generated by RepRapFirmware Configuration Tool v3.3.12 on Wed Aug 24 2022 12:56:11 GMT+0200 (Mitteleuropäische Sommerzeit)
G91 ; relative positioning
;G1 H2 Z5 F6000 ; lift Z relative to current position
G1 H1 X-505 Y-505 F1800 ; move quickly to X and Y axis endstops and stop there (first pass)
G1 H2 X5 Y5 F6000 ; go back a few mm
G1 H1 X-505 Y-505 F360 ; move slowly to X and Y axis endstops once more (second pass)
;G1 H1 Z705 F360 ; move Z up stopping at the endstop
G1 X150 Y150
G30
G90 ; absolute positioning
G92 Z700 ; set Z position to axis maximum (you may want to adjust this)

; Uncomment the following lines to lift Z after probing
;G91 ; relative positioning
;G1 Z5 F100 ; lift Z relative to current position
;G90 ; absolute positioning

[jay_s_uk]

@axiom said in z probe not referenced:

;G1 H2 Z5 F6000 ; lift Z relative to current position

this line is a good idea to have

@axiom said in z probe not referenced:

G92 Z700 ; set Z position to axis maximum (you may want to adjust this)

this line should be removed.

And what value does your probe show as having on the status screen?

[axiom]

@jay_s_uk now comes the message:
Error: Failed to enable endstops

nwe code:
; homeall.g
; called to home all axes
;
; generated by RepRapFirmware Configuration Tool v3.3.12 on Wed Aug 24 2022 12:56:11 GMT+0200 (Mitteleuropäische Sommerzeit)
G91 ; relative positioning
G1 H2 Z5 F6000 ; lift Z relative to current position
G1 H1 X-505 Y-505 F1800 ; move quickly to X and Y axis endstops and stop there (first pass)
G1 H2 X5 Y5 F6000 ; go back a few mm
G1 H1 X-505 Y-505 F360 ; move slowly to X and Y axis endstops once more (second pass)
;G1 H1 Z705 F360 ; move Z up stopping at the endstop
G1 X150 Y150
G30
G90 ; absolute positioning
;G92 Z700 ; set Z position to axis maximum (you may want to adjust this)

; Uncomment the following lines to lift Z after probing
;G91 ; relative positioning
;G1 Z5 F100 ; lift Z relative to current position
;G90 ; absolute positioning

[axiom]

@jay_s_uk

[jay_s_uk]

@axiom that shows that your probe is triggered already. what type of probe is it?

[axiom]

@jay_s_uk
a capacitive proximity sensor:
https://www.amazon.de/Heschen-kapazitiver-Näherungsschalter-Sensor-LJC18-A3-H-Z-Normalöfnung/dp/B071J6PXD1/ref=sr_1_5?__mk_de_DE=ÅMÅŽÕÑ&crid=1NG0J5PZMIZC4&keywords=kapazitiver+sensor&qid=1661366023&sprefix=kapizativer+sensor%2Caps%2C138&sr=8-5

i got the same for my little ender printer and it works since 2 years

[jay_s_uk]

@axiom you may need to invert the signal
e.g. M558 P1 C"!zprobe.in"
but you should test it before trying to home with it

[axiom]

@jay_s_uk
now the z-axis moves down instead of up when homing...but it responds to my hand and stops

[jay_s_uk]

@axiom you need to invert the direction of your Z axis then. It should be negative movement going up and positive going down

[axiom]

@jay_s_uk And how do I do that?

[jay_s_uk]

@axiom Change the S value in each M569 for the Z drivers. If its 0 change it to 1 and vice versa

[axiom]

@jay_s_uk how do i know which ones are for the z-axis...since i connected two, i don't want them to work in opposite directions...that might break the motors

[jay_s_uk]

@axiom you've mapped the driver numbers in M584