Euclid facility

[A Former User]

My bed 350x350x350 and prob euclid X0 y8. 5

[Phaedrux]

M558 K0 P5 C"^io2.in" H8 F300 60 T9000 A3 S0.01
G31 K0 P500 X-27.955 Y-18.716 Z1.033

If you include K0, you need to use K0 everywhere else the probe is called. You only have a single probe, so remove K0 from your config where you have it.

In your bed.g and home all you have a bunch of moves to pick the probe but then you also call the probe deploy. Your pickup moves should just be in the deploy macro.

G1 Y8.5 F6000 ; Pick Up Klicky
G1 X20 F2000 ;
G1 X0 F1000 ; Pick Up Klicky
G1 Y30 F1000 ;
G1 Y50 F6000 ; Pick Up Klicky
M401 ; deploy Z probe (omit if using bltouch)

[A Former User]

@phaedrux ok thank you I have to change the probe control in the bed m558 and g31?

[A Former User]

as this

[A Former User]

https://youtu.be/9wJ2RCimWXU
it gives me that

[Phaedrux]

@sgk said in Euclid facility:

as this

No. That's not what I meant at all. Your deploy and retract macros seem fine. You just need to call them with M401 and M402 in your bed.g and homeall.g files when you want to pick up or two away the probe. You don't need the manual G1 moves to pick it up there.

Did you remove the K0?

[A Former User]

@phaedrux k0 deleted

[A Former User]

I'm really sorry I'm completely lost at this point

[Phaedrux]

And return your deployprobe.g macro to how it was before?

With K0 removed, does G28, G32, and G29 function now?

[A Former User]

@phaedrux
I deleted my deploy and retract and I didn't save

[Phaedrux]

@sgk said in Euclid facility:

retractprobe.g homez.g homeall.g deployprobe.g config.g bed.g

want the files in raw or it goes in ZIP

Good thing you uploaded them here.

[A Former User]

@phaedrux yes nice

[A Former User]

it works but not very well every time the probe feels it comes home

[A Former User]

I will make a video

[A Former User]

and above all it does not balance the left and right bed

[A Former User]

https://youtu.be/Iv2z8CIwCVc

[A Former User]

[jumpedwithbothfeet]

@sgk Have you changed bed.g to what @Phaedrux suggested? it should now look like this -

; bed.g
; called to perform automatic bed compensation via G32
;
; generated by Ben Levi - BLV developer as a basic version

M561 												; clear any bed transform
G91               									; relative positioning
G1 H2 Z5 F6000   									; lift Z relative to current position
G90              									; absolute positioning
G28 												; home all

M401 ; deploy Z probe (omit if using bltouch)
G30 P0 X10 Y175 Z-99999 							; probe near a leadscrew, half way along Y axis
G30 P1 X330 Y175 Z-99999 S2 						; probe near a leadscrew and calibrate 2 motors
M402 ; retract probe (omit if using bltouch)                  

M291 P"Leveling finished !" R"Probing.." S1 T2

once you have done that go into your deployprobe.g find the line that says -

G0 X170 Y170 G3000 ; move to the center of the bed

and change it to read to read, to correct the warning -

G0 X170 Y170 F3000 ; move to the center of the bed

[A Former User]

hello to all of you it's finally starting to work thank you to all of you. I have to settle because the probe often comes home before doing g32 or g29. but it works it works thank you thank you thank you you're really king

[A Former User]

thank you to all and to the group