Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    No movement with any command

    Scheduled Pinned Locked Moved
    MultiAxis Printing
    7
    53
    2.4k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • Phaedruxundefined
      Phaedrux Moderator
      last edited by

      Please copy and paste the text of your config.g into a post here.

      Z-Bot CoreXY Build | Thingiverse Profile

      zecretonundefined 1 Reply Last reply Reply Quote 0
      • zecretonundefined
        zecreton @Phaedrux
        last edited by

        @Phaedrux i can't access dwc

        1 Reply Last reply Reply Quote 0
        • Phaedruxundefined
          Phaedrux Moderator
          last edited by

          Remove the SD card from the Duet and use your computer to read the config.g file.

          Z-Bot CoreXY Build | Thingiverse Profile

          zecretonundefined 2 Replies Last reply Reply Quote 0
          • zecretonundefined
            zecreton @Phaedrux
            last edited by

            @Phaedrux oops sorry i forgot that

            1 Reply Last reply Reply Quote 0
            • zecretonundefined
              zecreton @Phaedrux
              last edited by

              @Phaedrux ; Configuration file for RepRapFirmware on Duet 3 Main Board 6XD
              ; executed by the firmware on start-up
              ;
              ; generated by RepRapFirmware Configuration Tool v3.5.3 on Tue Jun 25 2024 21:16:10 GMT-0400 (Eastern Daylight Time)

              ; General
              G90 ; absolute coordinates
              M83 ; relative extruder moves
              M550 P"Duet 3" ; set hostname

              ; Network
              M551 P"Raphaelbreton2008" ; set machine password
              M552 P0.0.0.0 S1 ; configure Ethernet adapter
              M586 P0 S1 ; configure HTTP

              ; Motor Idle Current Reduction
              M906 I30 ; set motor current idle factor
              M84 S30 ; set motor current idle timeout

              ; External Drivers
              M569 P0.0 S1 R0 T5:5:10:0 ; driver 0.0 goes forwards and requires an active-low enable signal (X axis)
              M569 P0.1 S1 R0 T5:5:10:0 ; driver 0.1 goes forwards and requires an active-low enable signal (Y axis)
              M569 P0.2 S1 R0 T5:5:10:0 ; driver 0.2 goes forwards and requires an active-low enable signal (Z axis)

              ; Axes
              M584 X0.0 Y0.1 Z0.2 ; set axis mapping
              M350 X16 Y16 Z16 I0 ; configure microstepping without interpolation
              M92 X80 Y80 Z400 ; configure steps per mm
              M208 X0:1200 Y0:200 Z0:200 ; set minimum and maximum axis limits
              M566 X900 Y900 Z12 ; set maximum instantaneous speed changes (mm/min)
              M203 X6000 Y6000 Z180 ; set maximum speeds (mm/min)
              M201 X500 Y500 Z20 ; set accelerations (mm/s^2)

              ; Kinematics
              M669 K0 ; configure Cartesian kinematics

              ; Endstops
              M574 X1 P"io0.in" S1 ; configure X axis endstop
              M574 Y1 P"io1.in" S1 ; configure Y axis endstop
              M574 Z1 P"io2.in" S1 ; configure Z axis endstop

              1 Reply Last reply Reply Quote 0
              • Phaedruxundefined
                Phaedrux Moderator
                last edited by

                Are you able to connect to the Duet via USB cable and use terminal software like YAT to send commands to it?

                described here: https://docs.duet3d.com/en/How_to_guides/Getting_connected/Getting_connected_to_your_Duet#h-2-connect-your-duet-via-usb

                Z-Bot CoreXY Build | Thingiverse Profile

                zecretonundefined 1 Reply Last reply Reply Quote 0
                • zecretonundefined
                  zecreton @Phaedrux
                  last edited by

                  @Phaedrux yes

                  1 Reply Last reply Reply Quote 0
                  • Phaedruxundefined
                    Phaedrux Moderator
                    last edited by

                    What happens if you follow along with the rest of that "Getting connected" guide?

                    Z-Bot CoreXY Build | Thingiverse Profile

                    zecretonundefined 1 Reply Last reply Reply Quote 0
                    • zecretonundefined
                      zecreton @Phaedrux
                      last edited by

                      @Phaedrux i doesn't work bc when i send M552 S1 P0.0.0.0, it answers with just ok, and when i send M552, i can see that it gave 0.0.0.0 as an ip address

                      1 Reply Last reply Reply Quote 0
                      • Phaedruxundefined
                        Phaedrux Moderator
                        last edited by

                        How do you have the Duet connected to your network?

                        Does the network cable you have going to the Duet work if you try to connect it to a computer?

                        Z-Bot CoreXY Build | Thingiverse Profile

                        zecretonundefined Phaedruxundefined 2 Replies Last reply Reply Quote 0
                        • zecretonundefined
                          zecreton @Phaedrux
                          last edited by

                          @Phaedrux it is plugged with a ethernet cable in the router

                          1 Reply Last reply Reply Quote 0
                          • Phaedruxundefined
                            Phaedrux Moderator @Phaedrux
                            last edited by

                            @Phaedrux said in No movement with any command:

                            Does the network cable you have going to the Duet work if you try to connect it to a computer?

                            Z-Bot CoreXY Build | Thingiverse Profile

                            zecretonundefined 3 Replies Last reply Reply Quote 0
                            • zecretonundefined
                              zecreton @Phaedrux
                              last edited by

                              @Phaedrux yea sorry i didn't have the time to check, do you have the guide?

                              1 Reply Last reply Reply Quote 0
                              • zecretonundefined
                                zecreton @Phaedrux
                                last edited by

                                @Phaedrux nvm i don't know what was the problem but i just powered it on and thew ethernet works fine

                                1 Reply Last reply Reply Quote 0
                                • zecretonundefined
                                  zecreton @Phaedrux
                                  last edited by

                                  @Phaedrux i tested with a multimeter and i can see that in the driver entry, the pul and dir are receiving power, but not the enable, and on the output i don't know what to test

                                  1 Reply Last reply Reply Quote 0
                                  • Phaedruxundefined
                                    Phaedrux Moderator
                                    last edited by

                                    Enable is low by default. Your drivers seem to require a high signal.

                                    https://docs.duet3d.com/en/User_manual/Connecting_hardware/Motors_connecting_external#configuring-the-enable-polarity

                                    See here for changing the enable polarity.

                                    Z-Bot CoreXY Build | Thingiverse Profile

                                    zecretonundefined 1 Reply Last reply Reply Quote 0
                                    • zecretonundefined
                                      zecreton @Phaedrux
                                      last edited by

                                      @Phaedrux yea i already changed it to high

                                      1 Reply Last reply Reply Quote 0
                                      • Phaedruxundefined
                                        Phaedrux Moderator
                                        last edited by

                                        Have you tested the enable pin output with your multimeter at the board side?
                                        Does the cable have continuity?
                                        Have you tried a different driver output?

                                        https://docs.duet3d.com/duet_boards/duet_3_mb6xd/duet3_mb_6xd_v1.0_later_dvr_conn.png

                                        Z-Bot CoreXY Build | Thingiverse Profile

                                        zecretonundefined 2 Replies Last reply Reply Quote 0
                                        • zecretonundefined
                                          zecreton @Phaedrux
                                          last edited by

                                          @Phaedrux i can see a 5v signal when no command is sent, but it drops to 0v when i send a signal, is that normal?

                                          Phaedruxundefined 1 Reply Last reply Reply Quote 0
                                          • zecretonundefined
                                            zecreton @Phaedrux
                                            last edited by

                                            @Phaedrux yea,i get the same thing on the driver side

                                            1 Reply Last reply Reply Quote 0
                                            • First post
                                              Last post
                                            Unless otherwise noted, all forum content is licensed under CC-BY-SA