Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    New XZmotors problem

    Scheduled Pinned Locked Moved
    Tuning and tweaking
    4
    17
    474
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • jay_s_ukundefined
      jay_s_uk @aceranic
      last edited by

      @aceranic post your config

      Owns various duet boards and is the main wiki maintainer for the Teamgloomy LPC/STM32 port of RRF. Assume I'm running whatever the latest beta/stable build is

      aceranicundefined 1 Reply Last reply Reply Quote 0
      • aceranicundefined
        aceranic @jay_s_uk
        last edited by

        ; Configuration file for Duet WiFi (firmware version 3)
        ; executed by the firmware on start-up
        ;
        ; generated by RepRapFirmware Configuration Tool v3.3.10 on Mon Dec 06 2021 21:58:20 GMT+0100 (Central European Standard Time)

        ; General preferences
        M575 P1 S1 B57600 ; enable support for PanelDue
        G90 ; send absolute coordinates...
        M83 ; ...but relative extruder moves
        M550 P"TazmanSW" ; set printer name
        M669 K2 X1:0:1 Y0:1:0 Z1:0:-1 ; select CoreXZ mode

        ; Network
        M552 S0 ; enable network
        M586 P0 S1 ; enable HTTP
        M587 P192.128.68.68 ; connect to access point "Network-ssid-123" using WPA2-PSK authentication at specified IP address
        M552 S1
        M586 P1 S0 ; enable FTP
        M586 P2 S0 ; enable Telnet

        ; Drives
        M569 P0 S0 ; physical drive 0 goes forwards
        M569 P1 S0 ; physical drive 1 goes forwards
        M569 P2 S0 ; physical drive 2 goes forwards
        M569 P3 S1 ; physical drive 3 goes backwards Extruder
        M584 X0 Y2 Z1 E3 ; set drive mapping
        ;M350 X16 I0 ; configure microstepping without interpolation
        M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
        M92 X80.00 Y80.00 Z80.00 E562.00 ; set steps per mm
        M566 X150.00 Y150.00 Z150.00 E240.00 ; set maximum instantaneous speed changes (mm/min)
        M203 X30000.00 Y30000.00 Z30000.00 E10000.00 ; set maximum speeds (mm/min)
        M201 X900.00 Y900.00 Z900.00 E3500.00 ; set accelerations (mm/s^2)
        M906 X1200 Y1200 Z1200 E1200 I0 ; set motor currents (mA) and motor idle factor in per cent
        M84 S2 ; Set idle timeout

        ; Axis Limits
        M208 X0 Y0 Z0 S1 ; set axis minima
        M208 X372 Y380 Z315 S0 ; set axis maxima

        ; Endstops
        M574 X1 S1 P"!xstop" ; configure switch-type (e.g. microswitch) endstop for low end on X via pin !xstop
        M574 Y1 S1 P"!ystop" ; configure switch-type (e.g. microswitch) endstop for low end on Y via pin !ystop
        ;M574 Z1 S1 P"!zstop" ; configure switch-type (e.g. microswitch) endstop for low end on Z via pin !zstop
        M574 Z1 S2 ; configure Z-probe endstop for low end on Z

        ; Z-Probe
        M950 S0 C"exp.heater3" ; create servo pin 0 for BLTouch
        M558 P9 C"^zprobe.in" H10 F1200:420 T6000 ; set Z probe type to bltouch and the dive height + speeds
        ;G31 P25 X-30 Y-15 Z2.90 ; set Z probe trigger value, offset and trigger height
        M557 X50:370 Y50:380 S50 ; define mesh grid
        M280 P0 S160 I1 ; Probe reset

        ; Heaters
        M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
        M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
        M307 H0 B1 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit
        M140 H0 ; map heated bed to heater 0
        M143 H0 S120 ; set temperature limit for heater 0 to 100C
        M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin e0temp
        M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to s ensor 1
        M307 H1 B0 S0.75 ; disable bang-bang mode for heater and set PWM limit
        M143 H1 S280 ; set temperature limit for heater 1 to 250C

        ; Fans
        M950 F0 C"fan0" Q255 ; create fan 0 on pin fan0 and set its frequency
        M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
        M950 F1 C"fan1" Q150 ; create fan 1 on pin fan1 and set its frequency
        M106 P1 S1 H1 T55 ; set fan 1 value. Thermostatic control is turned on

        ; Tools
        M563 P0 D0 H1 F0 S"Mosquito" ; define tool 0
        ;G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
        G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
        M563 P1 D0 H1 F0
        G10 P1 R0 S0
        M563 P2 D0 H1 F0
        G10 P2 R0 S0
        M563 P3 D0 H1 F0
        G10 P3 R0 S0

        ; Custom settings
        ;M572 D0 S0.3
        M564 H0
        M501
        M302 P1
        M950 P1 C"exp.heater4" ; allocate GPIO port1 to heater4 on expansion connector, 500Hz

        ;M955 P0 C"spi.cs4+spi.cs3" ; all wires connected to temp DB connector, no temperature daughterboard
        M593 P"zvdd" F56 ; use ZVD input shaping to cancel ringing at 40.5Hz

        M98 P"load_variables.g" ; Runs the macro in the file load_variables.g

        aceranicundefined 1 Reply Last reply Reply Quote 0
        • aceranicundefined
          aceranic @aceranic
          last edited by aceranic

          @aceranic I had to change direction as I was getting Phase warnings....
          Also I have 2 motors on Y axis, connected to 2 Z axis drivers.

          jay_s_ukundefined 1 Reply Last reply Reply Quote 0
          • jay_s_ukundefined
            jay_s_uk @aceranic
            last edited by

            @aceranic it could be a result of the fairly low jerk (M556) settings you have.
            Your acceleration settings are also very low (M201)

            Owns various duet boards and is the main wiki maintainer for the Teamgloomy LPC/STM32 port of RRF. Assume I'm running whatever the latest beta/stable build is

            aceranicundefined 1 Reply Last reply Reply Quote 0
            • aceranicundefined
              aceranic @jay_s_uk
              last edited by aceranic

              @jay_s_uk Ok, I didnt have such issue before with same settings. They are set higher is slicer.

              aceranicundefined 1 Reply Last reply Reply Quote 0
              • aceranicundefined
                aceranic @aceranic
                last edited by

                Increased current and accwl, jerk, still the same.

                aceranicundefined 1 Reply Last reply Reply Quote 0
                • aceranicundefined
                  aceranic @aceranic
                  last edited by

                  Incresed all values but still no luckScreenshot_20250312_164054_Samsung Internet.jpg

                  jay_s_ukundefined 1 Reply Last reply Reply Quote 0
                  • jay_s_ukundefined
                    jay_s_uk @aceranic
                    last edited by

                    @aceranic i guess its mechanical issue

                    Owns various duet boards and is the main wiki maintainer for the Teamgloomy LPC/STM32 port of RRF. Assume I'm running whatever the latest beta/stable build is

                    aceranicundefined 1 Reply Last reply Reply Quote 0
                    • aceranicundefined
                      aceranic @jay_s_uk
                      last edited by

                      @jay_s_uk Not sure still. After board restart it was moving fine few times full X travel. Then I started the print and same issue again.
                      I tried one older print large size, same.

                      1 Reply Last reply Reply Quote 0
                      • Phaedruxundefined
                        Phaedrux Moderator
                        last edited by

                        Are you using mesh compensation? Can you try disabling it if you are?

                        Z-Bot CoreXY Build | Thingiverse Profile

                        aceranicundefined 1 Reply Last reply Reply Quote 0
                        • aceranicundefined
                          aceranic @Phaedrux
                          last edited by

                          @Phaedrux Hi. Will try. Only thing I didnt try yet.

                          aceranicundefined 1 Reply Last reply Reply Quote 0
                          • aceranicundefined
                            aceranic @aceranic
                            last edited by

                            Yep. It seems that 25mm grid was too much to chew. Thanks!!!!

                            By the way Phaedrux, I ordered BTT extension for 3 drivers for my MMU. Will need help with that 😁

                            droftartsundefined 1 Reply Last reply Reply Quote 0
                            • droftartsundefined
                              droftarts administrators @aceranic
                              last edited by

                              @aceranic said in New XZmotors problem:

                              I ordered BTT extension for 3 drivers for my MMU.

                              If it's this board https://github.com/bigtreetech/BTT-Expansion-module/blob/master/BTT EXP-MOT/BTT EXP-MOT V1.0User Guide.pdf then I think you can only use two of the drivers with Duet 2 WiFi, as it has to be connected in STEP/DIR mode, not UART or SPI mode. Is that correct @jay_s_uk ?

                              Ian

                              Bed-slinger - Mini5+ WiFi/1LC | RRP Fisher v1 - D2 WiFi | Polargraph - D2 WiFi | TronXY X5S - 6HC/Roto | CNC router - 6HC | Tractus3D T1250 - D2 Eth

                              jay_s_ukundefined aceranicundefined 2 Replies Last reply Reply Quote 0
                              • jay_s_ukundefined
                                jay_s_uk @droftarts
                                last edited by

                                @droftarts yep, thats correct. Step/Dir only with no UART or SPI control

                                Owns various duet boards and is the main wiki maintainer for the Teamgloomy LPC/STM32 port of RRF. Assume I'm running whatever the latest beta/stable build is

                                1 Reply Last reply Reply Quote 0
                                • aceranicundefined
                                  aceranic @droftarts
                                  last edited by aceranic

                                  @droftarts yep, that is the one.
                                  The plan is to use 2 drivers for MMU.
                                  This should be no problem I believe.
                                  Is there a guide enywhere for the configuration of this board?

                                  droftartsundefined 1 Reply Last reply Reply Quote 0
                                  • droftartsundefined
                                    droftarts administrators @aceranic
                                    last edited by

                                    @aceranic said in New XZmotors problem:

                                    Is there a guide enywhere for the configuration of this board?

                                    Just the linked BTT PDF, and https://docs.duet3d.com/en/User_manual/Connecting_hardware/Motors_connecting_external

                                    Ian

                                    Bed-slinger - Mini5+ WiFi/1LC | RRP Fisher v1 - D2 WiFi | Polargraph - D2 WiFi | TronXY X5S - 6HC/Roto | CNC router - 6HC | Tractus3D T1250 - D2 Eth

                                    1 Reply Last reply Reply Quote 0
                                    • First post
                                      Last post
                                    Unless otherwise noted, all forum content is licensed under CC-BY-SA