Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    Firmware 2.0RC2b/1.21.1 RC2b released

    Scheduled Pinned Locked Moved
    Firmware installation
    19
    52
    7.3k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • gen2engundefined
      gen2eng @gen2eng
      last edited by

      @gen2eng said in Firmware 2.0RC2b/1.21.1 RC2b released:

      @dc42

      It was hanging at about 41sec. I did a hard reset and simulation ran fine on a different file. After the current print job finishes, I will try again.

      I tried the simulation immediately after the upgrade. Any chance it needed a hard reset?

      I'm running on a 1.03 Duet Wifi.

      Ran it again, and it did not hang. The original hang was around 41% complete, not 41 sec.

      1 Reply Last reply Reply Quote 0
      • Danalundefined
        Danal
        last edited by

        Loaded:

        
        Firmware Name:	RepRapFirmware for Duet 2 WiFi/Ethernet
        Firmware Electronics:	Duet WiFi 1.02 or later
        Firmware Version:	2.0(RTOS)RC2b (2018-05-13b3)
        WiFi Server Version:	1.21
        Web Interface Version:	1.21.1-RC4
        

        No prints (yet)

        Delta / Kossel printer fanatic

        Danalundefined 1 Reply Last reply Reply Quote 0
        • Danalundefined
          Danal
          last edited by

          You guys are probably past this... but... just in case, I ran a simulation of the skew tower file. Ran to completion, no issues.

          7:29:27 PMFile 1526229129318-cfdmp_skew-tower.gcode will print in 3h 7m plus heating time
          7:27:27 PMM37 P"1526229129318-cfdmp_skew-tower.gcode"
          Simulating print of file 1526229129318-cfdmp_skew-tower.gcode

          Delta / Kossel printer fanatic

          1 Reply Last reply Reply Quote 0
          • Dr_Ju_Juundefined
            Dr_Ju_Ju
            last edited by

            Updated successfully with no problems, but I'm having issues while printing (multiple times via USB or local gcode), in that 1\2 to 3\4 of the way through a print, I get "Error: Heating fault on heater 1, temperature excursion exceeded 15.0°C".

            This results in two conditions, a local print, parks the toolhead to XY cordinates shuts off Bed & halts the printer and errors with Resume-after-power-fail state saved.

            If I'm printing from USB (Simplify3D), when the failure occurs, S3D knows somthing has gone wrong, but the printer keeps on moving, and keeps the bed heater running, but is unable to extrude.

            I accept that printer won't know what is being printed, but should the printer do a hard re-set on hard error to at least kill all running prints ??

            I was\am attempting to print ABS parts for Panobot on DBot 300x300x300 coreXY printer, driven by a DuetEthernet, so using Bed 110 Hotend 255.

            I've chased all the wiring\checked all connectors, at various points around the bed area, bending strains are reduced as I'm using cable chains.

            I'm almost at the point where either the problem is on the Board or the heater cartridge (E3D).

            Next chance I get I'll re-map the heater to E1, if that fails to fix it, I'll replace the cartridge. But its strange that everything works fine for long periods of time, fails, & the one time it has happened while I was near, a board re-set let it resume.

            Julian,

            Old goat, learning new things….

            1 Reply Last reply Reply Quote 0
            • gen2engundefined
              gen2eng
              last edited by

              I've just completed a 10.5 hour print on this release without issue. It appears to be stable with the exception of the weird simulation hang. After a hard reset, the simulation ran fine.

              1 Reply Last reply Reply Quote 0
              • zerspaner_gerdundefined
                zerspaner_gerd @dc42
                last edited by

                Does Duet actually choose the correct firmware version automatically? I actually went out of 1.21.1. Now I have 2.0, or have I selected the wrong file?

                @dc42 said in Firmware 2.0RC2b/1.21.1 RC2b released:

                M502 now resets all firmware parameters back to the values in config.g except network parameters

                Are there any other exclusions or only one?

                I get this message, is this correct?

                M502
                Error: Could not set WiFi hostname
                HTTP is enabled on port 80
                FTP is disabled
                TELNET is disabled
                
                Firmware Name:	RepRapFirmware for Duet 2 WiFi/Ethernet
                Firmware Electronics:	Duet WiFi 1.02 or later
                Firmware Version:	2.0(RTOS)RC2b (2018-05-13b3)
                WiFi Server Version:	1.21
                Web Interface Version:	1.21.1-RC4'''

                Board: Duet WiFi 1.03 | Firmware Version: 3.1.1 | WiFi Server Version: 1.23 | Web Interface Version: 3.1.1

                1 Reply Last reply Reply Quote 0
                • brandonhundefined
                  brandonh
                  last edited by

                  FWIW after upgrading I also experienced the heater fault issue; 4 times on an 8 hr print. Probably just bad luck with a loose connector, as after a reset and restore the print started right back up, and I didn't have the heater calibrated either, and I had seen this happen long ago too. Simulation worked fine with the updated PanelDue and it would be amazing to see the simulation done as a parallel thread to calculate upon print start. Originally had an issue with losing the web interface, but copying over a new web directory solved that.

                  Saw a small improvement in WiFi transfer; now close to 500 KB/s, up from about 400 KB/s.

                  Good work!

                  1 Reply Last reply Reply Quote 0
                  • timcurtis67undefined
                    timcurtis67
                    last edited by

                    So far the new firmware and DWC work great. Love the ability to upload files while homing the printer.

                    A good test will come tonight, Ditto printing (IDEX) on a 8 hour print run.

                    1 Reply Last reply Reply Quote 0
                    • BMMalundefined
                      BMMal
                      last edited by

                      I've been using this since it was released and have not noticed any issues yet.

                      Duet Ethernet - Most likely the most recent Edge firmware
                      Duet X5
                      7" Panel Due V2
                      Cartesian, 4 Nozzles with Flex3Drives, Heated Chamber, Simple Switch Filament Sensing

                      1 Reply Last reply Reply Quote 0
                      • timcurtis67undefined
                        timcurtis67
                        last edited by

                        Last night While printing a long running part, I uploaded a 17mb file at speeds of 700KB/s with no issues.

                        Well done David!

                        1 Reply Last reply Reply Quote 0
                        • Scachiundefined
                          Scachi
                          last edited by

                          I installed RC3 (or RC2b) and printed a couple of small things (~2 hours prints each) without any problems.
                          The baby stepping command seems to be responding a bit faster than before 👍

                          1 Reply Last reply Reply Quote 0
                          • cgcaferundefined
                            cgcafer
                            last edited by

                            Hi,
                            I am using RTOS version and generally no problem. Today i add relay unit for controlling 24V line (M80 and M81).
                            It is work but when i first start the printer 7" Panel due still connection state, if i send M80 from DWC then paneldue's state change to idle. After that paneldue can send M80 and M81 without any problem.

                            Is this firmware problem or i made any mistake?
                            Thanks,

                            0_1526481376738_23edc11d-852c-481f-a1a2-c10b923acb58-resim.png

                            dc42undefined 1 Reply Last reply Reply Quote 0
                            • Catalin_ROundefined
                              Catalin_RO
                              last edited by

                              Did a run on WorkBee with 2.0RC2b and the part was identical to the one machined with 1.21.

                              1 Reply Last reply Reply Quote 0
                              • dc42undefined
                                dc42 administrators @cgcafer
                                last edited by dc42

                                @cgcafer said in Firmware 2.0RC2b/1.21.1 RC2b released:

                                Hi,
                                I am using RTOS version and generally no problem. Today i add relay unit for controlling 24V line (M80 and M81).
                                It is work but when i first start the printer 7" Panel due still connection state, if i send M80 from DWC then paneldue's state change to idle. After that paneldue can send M80 and M81 without any problem.

                                Is this firmware problem or i made any mistake?
                                Thanks,

                                The PanelDue firmware needs to be updated to support the new Off status returned by the firmware when VIN power is not present.

                                Duet WiFi hardware designer and firmware engineer
                                Please do not ask me for Duet support via PM or email, use the forum
                                http://www.escher3d.com, https://miscsolutions.wordpress.com

                                1 Reply Last reply Reply Quote 0
                                • cgcaferundefined
                                  cgcafer
                                  last edited by

                                  Hi,
                                  Thank you for your answer, tomorrow morning i will check it. Which version it should be?

                                  1 Reply Last reply Reply Quote 0
                                  • dc42undefined
                                    dc42 administrators
                                    last edited by

                                    The version that hasn't been released yet!

                                    Duet WiFi hardware designer and firmware engineer
                                    Please do not ask me for Duet support via PM or email, use the forum
                                    http://www.escher3d.com, https://miscsolutions.wordpress.com

                                    1 Reply Last reply Reply Quote 0
                                    • Danalundefined
                                      Danal @Danal
                                      last edited by Danal

                                      @danal said in Firmware 2.0RC2b/1.21.1 RC2b released:

                                      Loaded:

                                      
                                      Firmware Name:	RepRapFirmware for Duet 2 WiFi/Ethernet
                                      Firmware Electronics:	Duet WiFi 1.02 or later
                                      Firmware Version:	2.0(RTOS)RC2b (2018-05-13b3)
                                      WiFi Server Version:	1.21
                                      Web Interface Version:	1.21.1-RC4
                                      

                                      Have now printed long-ish (couple of hours) and very short (10 minute) prints with no detectable issues. This is on the large-ish custom delta (600x600x600) at 24V with separate mains heatbed.

                                      Delta / Kossel printer fanatic

                                      dc42undefined 1 Reply Last reply Reply Quote 0
                                      • dc42undefined
                                        dc42 administrators @Danal
                                        last edited by

                                        Thanks to all of you who have provide feedback on RC2B. I'm looking to fix a few old bugs before the 2.0 release, so there will probably be a RC3 next week.

                                        Duet WiFi hardware designer and firmware engineer
                                        Please do not ask me for Duet support via PM or email, use the forum
                                        http://www.escher3d.com, https://miscsolutions.wordpress.com

                                        1 Reply Last reply Reply Quote 0
                                        • Dr_Ju_Juundefined
                                          Dr_Ju_Ju
                                          last edited by

                                          I've now had a chance to swap Heater 1 for Heater 2, which has appeared to have fixed my issue with heater crashing & failing print, but it does mean the a board I bought in early January has problems (when I got the board, there were unsoldered joints !!).

                                          One issues I have with this is that the Web interface works as expected, but the PanelDue still shows a "phantom" heater H1, with Current\Active\Standby boxes as well as the re-mapped heater as expected.

                                          Julian,

                                          Old goat, learning new things….

                                          dc42undefined 1 Reply Last reply Reply Quote 0
                                          • dc42undefined
                                            dc42 administrators @Dr_Ju_Ju
                                            last edited by

                                            @dr_ju_ju said in Firmware 2.0RC2b/1.21.1 RC2b released:

                                            I've now had a chance to swap Heater 1 for Heater 2, which has appeared to have fixed my issue with heater crashing & failing print, but it does mean the a board I bought in early January has problems (when I got the board, there were unsoldered joints !!).

                                            If you believe your Duet was delivered and still is faulty, please ask for it to be replaced under warranty.

                                            Duet WiFi hardware designer and firmware engineer
                                            Please do not ask me for Duet support via PM or email, use the forum
                                            http://www.escher3d.com, https://miscsolutions.wordpress.com

                                            Dr_Ju_Juundefined 1 Reply Last reply Reply Quote 0
                                            • First post
                                              Last post
                                            Unless otherwise noted, all forum content is licensed under CC-BY-SA