Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    2 Z motors, to endstops

    Scheduled Pinned Locked Moved
    Tuning and tweaking
    5
    21
    2.0k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • Torroundefined
      Torro
      last edited by

      No, all is running correct AFTER i homed Z.
      nothing moves if Z is not homed.

      1 Reply Last reply Reply Quote 0
      • aidarundefined
        aidar
        last edited by

        Please post your full config.g as well as config-override.g, (those on duet sd card, not somewhere in your computer, to eliminate possibilty that your backup ones in computer are not up to date)

        1 Reply Last reply Reply Quote 0
        • Torroundefined
          Torro
          last edited by

          Hi,

          no config-override in the system.

          ; Configuration file for Duet WiFi (firmware version 1.21)
          ; executed by the firmware on start-up
          ;
          ; generated by RepRapFirmware Configuration Tool v2 on Sat Nov 24 2018 10:45:17 GMT+0100 (Mitteleuropäische Normalzeit)

          ; General preferences
          M80
          G90 ; Send absolute coordinates...
          M83 ; ...but relative extruder moves

          M667 S1 ; Select CoreXY mode

          ; Network
          M550 P"MKC" ; Set machine name
          M552 S1 ; Enable network
          M586 P0 S1 ; Enable HTTP
          M586 P1 S0 ; Disable FTP
          M586 P2 S0 ; Disable Telnet

          ; Specials

          M307 H2 A-1 C-1 D-1 ; disable the heater functionality

          ; Drives
          M569 P0 S1 ; Drive 0 goes forwards
          M569 P1 S1 ; Drive 1 goes forwards
          M569 P2 S1 ; Drive 2 goes forwards Z @ Xmin
          M569 P3 S1 ; Drive 3 goes forwards
          M569 P4 S1 ; Drive 4 goes forwards Z @ Xmax
          M584 X0 Y1 Z2:3 U3 E4 P3 ; two Z motors connected to driver outputs Z and E1 Hide U
          M350 X16 Y16 Z16 U16 E16 I1 ; Configure microstepping with interpolation
          M92 X80.00 Y80.00 Z160 U160 E420.00 ; Set steps per mm
          M566 X900.00 Y900.00 Z12.00 U12.00 E120.00 ; Set maximum instantaneous speed changes (mm/min)
          M203 X30000.00 Y30000.00 Z4000.00 U4000.00 E4000.00 ; Set maximum speeds (mm/min)
          M201 X1500.00 Y1500.00 Z500.00 U500.00 E10000.00 ; Set accelerations (mm/s^2)
          M906 X800.00 Y800.00 Z800.00 U800.00 E800.00 I40 ; Set motor currents (mA) and motor idle factor in per cent
          M84 S3000 ; Set idle timeout

          ; Axis Limits
          M208 X0 Y-1 Z0 S1 ; Set axis minima
          M208 X240 Y260 Z288 S0 ; Set axis maxima

          ; Endstops
          M574 X1 Y1 S0 ; Set active high endstops
          M574 Z1 U1 S1

          ; Z-Probe
          ;M558 P1 H5 F120 T6000 ; Disable Z probe but set dive height, probe speed and travel speed;
          ;G31 P500 X0 Y50 Z1.45
          ;M557 X20:220 Y70:240 S20 ; Define mesh grid

          ; Heaters
          M305 P0 T100000 B4388 C7.060000e-8 R4700 ; Set thermistor + ADC parameters for heater 0
          M143 H0 S130 ; Set temperature limit for heater 0 to 120C
          M305 P1 T100000 B4388 C7.060000e-8 R4700 ; Set thermistor + ADC parameters for heater 1
          M143 H1 S280 ; Set temperature limit for heater 1 to 280C
          M307 H1 A438.2 C134.9 D3.9 B0

          ; Fans
          M106 P0 S0 I0 F500 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
          M106 P1 S1 I0 F500 H1 T45 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
          M106 P2 T45:55 H100:101:102 ; Set fan 2 value,
          M912 P0 S-3,5

          ; Tools
          M563 P0 D0 H1 ; Define tool 0
          G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets
          G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C

          ; Automatic power saving
          M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; Set voltage thresholds and actions to run on power loss

          ; Custom settings are not configured

          ;

          1 Reply Last reply Reply Quote 0
          • aidarundefined
            aidar
            last edited by

            Ok, config seems to be ok. So what exactly happens if you send G28 from DWC gcode console? If nothing moves, there should be some response message from duet why nothing moves. What that message says?

            1 Reply Last reply Reply Quote 0
            • Torroundefined
              Torro
              last edited by

              Just started a print...

              yesterday, there was no message from DWC.
              A click on "home all" did nothing, but i couldn´t move the motors by hand anymore.

              will test G28 asap

              1 Reply Last reply Reply Quote 0
              • Torroundefined
                Torro
                last edited by

                after powering up the printer, a single G28 without any parameter does nothing. the circle in the "send" button spins and spins and spins. when i click "emergency stop", a message "homing failed" appears.

                then i homed only Z. works. after that, G28 works without any issue, same as the button "homeall"

                1 Reply Last reply Reply Quote 0
                • aidarundefined
                  aidar
                  last edited by

                  That is odd. You are not supposed to be able home Z at all before X and Y are not homed. What firmware version are you using and what version of DWC?

                  1 Reply Last reply Reply Quote 0
                  • Torroundefined
                    Torro
                    last edited by

                    Duet Web Control 2.0.0-RC3

                    Electronics: Duet WiFi 1.02 or later
                    Firmware: RepRapFirmware for Duet 2 WiFi/Ethernet 2.02(RTOS) (2018-12-24b1)
                    Duet WiFi Server Version: 1.22

                    1 Reply Last reply Reply Quote 0
                    • Phaedruxundefined
                      Phaedrux Moderator @Torro
                      last edited by

                      @torro said in 2 Z motors, to endstops:

                      homeall
                      G91 ; relative positioning
                      G1 S1 X-300 Y-300 F5000 ; move quickly to X or Y endstop and stop there (first pass)
                      G1 S1 X-300
                      G1 S1 Y-300
                      G1 X10 Y10 F6000 ; go back a few mm
                      G1 S1 X-20 F360 ; move slowly to X axis endstop once more (second pass)
                      G1 S1 Y-20 ; then move slowly to Y axis endstop
                      M98 Phomez.g

                      Try changing M98 Phomez.g to G28 Z

                      Z-Bot CoreXY Build | Thingiverse Profile

                      Torroundefined 1 Reply Last reply Reply Quote 0
                      • Torroundefined
                        Torro
                        last edited by

                        Ok. I will try.

                        1 Reply Last reply Reply Quote 0
                        • Torroundefined
                          Torro
                          last edited by

                          I didn't test it yet, but i have an idea, i could put the home Z order on top in the first line. I Guess it works... 🙂

                          1 Reply Last reply Reply Quote 0
                          • thweundefined
                            thwe
                            last edited by thwe

                            On my CoreXY also with 2 Z-Motors and 2 Endstops (1 for Z and 1 for U - Drive 2 and 3) i have to home Z also at first.

                            Only for example - without any garanty - see my homeall.g:

                            ; ##############  homeall.g -> called to home all axes  ##############
                            
                            M98 Phomez.g                 ; X homing
                            
                            M98 Phomex.g                 ; Y homing
                            
                            M98 Phomey.g                 ; Z homing
                            
                            G90
                            
                            
                            ; #################    checking trigger height + Z null adjusting    #################
                            G1 X144 Y150 F12000
                            G1 Z20 F1800
                            G1 Z15 F1200
                            G1 Z10 F600
                            T0
                            G30                            ; Probe the bed at the current XY position, set the Z coordinate to the probe trigger height
                            G4 P200
                            G1 Z50 F1800
                            
                            ; END OF FILE
                            

                            and my homez.g:

                            ; ##############  homez.g -> called to home the Z axis  ##############
                            
                            G91                         ; relative positioning
                            
                            M584 Z2 U3 P4               ; Split Z into 2 (Z+U)
                            
                            G1 S1 Z999 U999 F600        ; Move the bed down in the Z direction. S1 to stop if endstop is triggered
                            G1 S2 Z-3 U-3 F600          ; Move the bed up 3mm in the -Z direction, ignore if axis are not homed
                            G1 S1 Z9 U9 F200            ; Move slowly in the +Z direction again to stop exactly at the homing switch
                            M400                        ; Wait for current moves to finish
                            
                            G4 P100
                            G1 S2 Z0.00 U0.00 F200      ; Compensation the limit switch from z-axis drive 2 (!!can be adjusted here!!)
                            G4 P100
                            
                            M584 Z2:3 P3                ; Join U to Z again
                            G4 P100
                            
                            G92 Z282.00                 ; set position of Z relativ to the bed (!!must be adjusted here!!)
                            
                            G90                         ; Back to absolute mode
                            
                            G1 S2 Z270 F900
                            ; End of file
                            

                            Thomas

                            1 Reply Last reply Reply Quote 0
                            • Torroundefined
                              Torro
                              last edited by

                              Good to know. Thanks!

                              1 Reply Last reply Reply Quote 0
                              • Torroundefined
                                Torro @Phaedrux
                                last edited by

                                @phaedrux said in 2 Z motors, to endstops:

                                @torro said in 2 Z motors, to endstops:

                                homeall
                                G91 ; relative positioning
                                G1 S1 X-300 Y-300 F5000 ; move quickly to X or Y endstop and stop there (first pass)
                                G1 S1 X-300
                                G1 S1 Y-300
                                G1 X10 Y10 F6000 ; go back a few mm
                                G1 S1 X-20 F360 ; move slowly to X axis endstop once more (second pass)
                                G1 S1 Y-20 ; then move slowly to Y axis endstop
                                M98 Phomez.g

                                Try changing M98 Phomez.g to G28 Z

                                Same behaviour. I just put the m98 phomez. G in the first line of homeall.g

                                Now it works as expected

                                1 Reply Last reply Reply Quote 0
                                • First post
                                  Last post
                                Unless otherwise noted, all forum content is licensed under CC-BY-SA