Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    Attempt to move motors when VIN is not in range DWC shows 0.5V

    Scheduled Pinned Locked Moved
    Duet Hardware and wiring
    vin not in range
    8
    50
    4.7k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • Phaedruxundefined
      Phaedrux Moderator @Magnusjen
      last edited by

      @magnusjen said in Attempt to move motors when VIN is not in range DWC shows 0.5V:

      DUET 2 WIFI 1.03

      The 1.03 boards have a fan fuse near the fan connectors. Check if it is blown.
      https://duet3d.dozuki.com/Wiki/Duet_Wiring_Diagrams

      Z-Bot CoreXY Build | Thingiverse Profile

      Magnusjenundefined 1 Reply Last reply Reply Quote 0
      • Magnusjenundefined
        Magnusjen @Phaedrux
        last edited by

        @phaedrux I have tested the fuses and the resistance is zero as it should be if it is working.

        1 Reply Last reply Reply Quote 0
        • genghisnico13undefined
          genghisnico13
          last edited by

          Perhaps you could measure the voltage in the following points, one (or both) are used to measure Vin and you should see close to Vin/11.
          The pictures may not match your board exactly.

          1_1552591335864_duet wifi r81_v1.jpg

          0_1552591335863_duet wifi R16_v1.jpg
          I don't know which side is GND.

          Magnusjenundefined 1 Reply Last reply Reply Quote 0
          • Magnusjenundefined
            Magnusjen @genghisnico13
            last edited by

            @genghisnico13 So, the top picture one is 24V (23.7 is the reading I get all the time but thats 24V) and the one in the lower picture is 23.5 which is odd, I measured it several times to ensure it was correct.

            genghisnico13undefined 1 Reply Last reply Reply Quote 0
            • genghisnico13undefined
              genghisnico13 @Magnusjen
              last edited by

              @magnusjen Interesting I would like to see what @dc42 has to say about it, but if I am not mistaken that doesn't look good at all.

              Magnusjenundefined 1 Reply Last reply Reply Quote 0
              • Magnusjenundefined
                Magnusjen @genghisnico13
                last edited by

                @genghisnico13 Yeah... I have lost hope, I am just waiting for someone to confirm it is dead.. I will take it as an expensive lesson in basic wiring.

                1 Reply Last reply Reply Quote 0
                • Vetiundefined
                  Veti
                  last edited by

                  it can be resoldered see information here:
                  https://duet3d.dozuki.com/Wiki/Connector_and_spare_part_numbers#Section_Fan_mosfet
                  but wait for DCs input

                  Magnusjenundefined 1 Reply Last reply Reply Quote 1
                  • Magnusjenundefined
                    Magnusjen @Veti
                    last edited by

                    @veti Well, sounds like I will just wire my old control board up if that is the case and wait for new electronics parts to arrive and the perfect day to sit super calm and solder it on.

                    But good to know there is a fix, I will just wait for DCs comment.

                    1 Reply Last reply Reply Quote 0
                    • dc42undefined
                      dc42 administrators
                      last edited by dc42

                      The voltage reported by DWC (and also in the M122 report) is the VIN voltage after the 7.5A fuse. That supply also feeds the stepper motors, 5V regulator and extruder heaters. A voltage divider with a ratio of 11:1 feeds the ADC input.

                      If the input to the voltage divider is 24V but the DWC reading is only 0.5V then I can see a few possibilities:

                      1. The upper resistor in the voltage divider is not soldered down or is cracked.
                      2. The ADC input pin is shorted to another signal that is close to ground potential.
                      3. The ADC has failed. But in that case I would expect the thermistor readings not to be correct.

                      My gut feeling is that your Duet can be got working again.

                      Does the extruder heater heat up when commanded to do so, despite the VIN reading of 0.5V in DWC and/or M122 ?

                      Duet WiFi hardware designer and firmware engineer
                      Please do not ask me for Duet support via PM or email, use the forum
                      http://www.escher3d.com, https://miscsolutions.wordpress.com

                      elmoretundefined Magnusjenundefined 2 Replies Last reply Reply Quote 0
                      • elmoretundefined
                        elmoret @dc42
                        last edited by

                        @dc42 He has a 1.03, not 1.04.

                        OP: can you post a photo of your board from above?

                        tenjinundefined Magnusjenundefined 2 Replies Last reply Reply Quote 0
                        • tenjinundefined
                          tenjin @elmoret
                          last edited by

                          @elmoret

                          is it possible this is the same issue the other guy had?

                          do you have a 10 pin connector hooked up to an LCD?

                          Magnusjenundefined 1 Reply Last reply Reply Quote 0
                          • Magnusjenundefined
                            Magnusjen @tenjin
                            last edited by

                            @tenjin Hi there, no I don't have an LCD and I have nothing going into the 10 pin connector.

                            1 Reply Last reply Reply Quote 0
                            • Magnusjenundefined
                              Magnusjen @dc42
                              last edited by

                              @dc42 Thanks for replying, you got the situation right, I will upload a picture of my board aswell as another guy commented.

                              The extruder heater heats up fine, I checked both at the nozzle "to see it was just an IT lie" and DWC reports the heating. I have taken a screenshot of my DWC.

                              I would be happy if whatever mistake I have made can be corrected, you guys have made an awesome board.

                              0_1552628048374_2019-03-15.png

                              I could not also add the picture of my board, I will do it as a reply to the other guy

                              1 Reply Last reply Reply Quote 0
                              • Magnusjenundefined
                                Magnusjen @elmoret
                                last edited by

                                @elmoret Hi there, here is a picture of the board from above, if you guys need it I can unplug everything.

                                0_1552628177522_2019-03-15 06.27.29-1.jpg
                                0_1552628198909_2019-03-15 06.27.20.jpg

                                1 Reply Last reply Reply Quote 0
                                • dc42undefined
                                  dc42 administrators
                                  last edited by dc42

                                  As this is such an unusual fault, and I can't think how it would have been caused by user error, I am happy to approve a warranty replacement if it's a genuine Duet and it was in warranty when the fault was reported. If it was out of warranty then I suggest that the board is sent to our US-based repairer for analysis and possible repair.

                                  Duet WiFi hardware designer and firmware engineer
                                  Please do not ask me for Duet support via PM or email, use the forum
                                  http://www.escher3d.com, https://miscsolutions.wordpress.com

                                  Magnusjenundefined 1 Reply Last reply Reply Quote 1
                                  • Magnusjenundefined
                                    Magnusjen @dc42
                                    last edited by

                                    @dc42 Hi, that is an amazing offer! I bought it Friday last week (2019.03.08) from RepRap.me in Denmark, they are one of your vendors in Denmark and I could not imagine them selling a knock off.

                                    How do I go about the warrenty replacement?

                                    1 Reply Last reply Reply Quote 0
                                    • dc42undefined
                                      dc42 administrators
                                      last edited by

                                      Contact RepRap.me and point them to this thread.

                                      Duet WiFi hardware designer and firmware engineer
                                      Please do not ask me for Duet support via PM or email, use the forum
                                      http://www.escher3d.com, https://miscsolutions.wordpress.com

                                      Magnusjenundefined 1 Reply Last reply Reply Quote 0
                                      • Magnusjenundefined
                                        Magnusjen @dc42
                                        last edited by

                                        @dc42 Thank you for your assistance, hopefully I can get the next to function and can post more interesting questions

                                        1 Reply Last reply Reply Quote 0
                                        • First post
                                          Last post
                                        Unless otherwise noted, all forum content is licensed under CC-BY-SA