Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    BLTouch working

    Scheduled Pinned Locked Moved
    Duet Hardware and wiring
    50
    266
    79.5k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • T3P3Tonyundefined
      T3P3Tony administrators
      last edited by

      Nice! Did you need to do anything not covered in the documentation to get it working (I realise you needed the latest firmware version)? If so can you let me know so I can update it. Also is it ok for me to link the first video as an example?

      www.duet3d.com

      1 Reply Last reply Reply Quote 0
      • W3DRKundefined
        W3DRK
        last edited by

        Sure feel free to use the video. I should have tidied up my workbench! I haven't seen any documentation related to using a BLTouch with RepRapFirmware, but it's pretty straight forward to get going…

        • BLTouch 5V leads are connected to expansion header pins 1-2, and the servo lead is connected to pin 21 (PWM for heater 3)

        • BLTouch endstop leads are paralleled with a 240ohm resistor as documented by Antclabs to make it safe for 3.3v logic and connected to E0 endstop header

        • [c]M307 H3 A-1 C-1 D-1[/c] is added to config.g to reserve pin 21 for M42 or servo use

        • M558 is set to probe type 4 and G31 is set for a very low trigger value since the BLTouch only triggers the endstop for 5ms

        • Deployprobe.g macro contains the line [c]M280 P3 S10 I1[/c] to deploy the BLTouch probe

        • Retractprobe.g macro contains the line [c]M280 P3 S90 I1[/c] to retract the BLTouch probe

        • Deploy and Retract macros are added to bed.g and homing macros

        And I think that's about it…

        The only issue I've run into so far is the very first probe deployment can take a few seconds before the BLTouch responds and actually pushes the probe down. I'm not sure if it's because the Duet take a little while to setup the PWM or maybe the BLTouch isn't truly 3.3v tolerant and requires a buffer after all, but I need to examine it further. After the first probe deployment it continues to respond quickly like I'd expect, so as a workaround I just deploy the probe at the very top of my homeall.g macro and by the time it gets around to homing Z, the probe has been deployed and everything works fine.

        1 Reply Last reply Reply Quote 0
        • dc42undefined
          dc42 administrators
          last edited by

          There appears to be a bug along the lines you describe when using heater 3 as a servo. It's on my list to fix in 1.17. The other expansion heater channels don't have the problem.

          Duet WiFi hardware designer and firmware engineer
          Please do not ask me for Duet support via PM or email, use the forum
          http://www.escher3d.com, https://miscsolutions.wordpress.com

          1 Reply Last reply Reply Quote 0
          • W3DRKundefined
            W3DRK
            last edited by

            Ok thanks for mentioning that! Certainly saves me some troubleshooting…

            @dc42:

            There appears to be a bug along the lines you describe when using heater 3 as a servo. It's on my list to fix in 1.17. The other expansion heater channels don't have the problem.

            1 Reply Last reply Reply Quote 0
            • dc42undefined
              dc42 administrators
              last edited by

              This bug is fixed in the 1.17dev4 build. It turned out to be an undocumented chip-level bug in the PWM subsystem and it took me hours to find a workaround.

              Duet WiFi hardware designer and firmware engineer
              Please do not ask me for Duet support via PM or email, use the forum
              http://www.escher3d.com, https://miscsolutions.wordpress.com

              1 Reply Last reply Reply Quote 1
              • W3DRKundefined
                W3DRK
                last edited by

                David, I can't thank you enough for all the hard work and dedication you contribute to this firmware! I'll install your 1.17 dev build this weekend and let you know how it works out.

                1 Reply Last reply Reply Quote 0
                • Alex9779undefined
                  Alex9779
                  last edited by

                  I was curious so I ordered one too.
                  I set all up so far for testing and but stumbled over something.
                  The BLTouch is 5V powered from the servo input so its output signal is also 5V.
                  I know, and it is described, the resistor is also provided, that I can use the 240ohms resistor between the output and ground to reduce the voltage.
                  But I am a proud beta tester of the Duex2 and it provides endstop ports where I can select the operating voltage…
                  All I need now would be a remapping possibility that a probe of type 4 (M558 P4) would not use E0 endstop but E2 or E3.
                  @dc42 would that be possible or is this outa reach? I just wanna be safe and a resistor crimped into the plug or soldered in somehow might break and then I have a problem. With the Duex now allowing 5V endstops I could omit the resistor and just use one of those native ports.

                  1 Reply Last reply Reply Quote 0
                  • dc42undefined
                    dc42 administrators
                    last edited by

                    That could be done, but it is not likely to happen soon because my priority is to finish the grid bed compensation code.

                    I think it is very unlikely that that 5V applied to an endstop input on the Duet WiFi would damage the microcontroller, because the endstop input includes a series resistor. The Z probe input is even better protected. So I suggest you use the resistor, connect it to the Z probe input, and select probe type 4.

                    Duet WiFi hardware designer and firmware engineer
                    Please do not ask me for Duet support via PM or email, use the forum
                    http://www.escher3d.com, https://miscsolutions.wordpress.com

                    1 Reply Last reply Reply Quote 0
                    • Alex9779undefined
                      Alex9779
                      last edited by

                      Hmmm but the manual states that type 4 uses E0, so how can I connect it to Z probe input?
                      Or are they the same?

                      Edit: reading between the lines of the documentation I assume yes… But I found no definite statement....

                      1 Reply Last reply Reply Quote 0
                      • dc42undefined
                        dc42 administrators
                        last edited by

                        Sorry, I meant type 5.

                        Duet WiFi hardware designer and firmware engineer
                        Please do not ask me for Duet support via PM or email, use the forum
                        http://www.escher3d.com, https://miscsolutions.wordpress.com

                        1 Reply Last reply Reply Quote 0
                        • W3DRKundefined
                          W3DRK
                          last edited by

                          David, I forgot to update that 1.17 dev4 does indeed fix the delay with heater 3 as a servo on a wired Duet. Everything is working absolutely perfectly and I'm extremely pleased with how well the BLTouch works. Thanks!

                          1 Reply Last reply Reply Quote 0
                          • W3DRKundefined
                            W3DRK
                            last edited by

                            @Alex9779:

                            I just wanna be safe and a resistor crimped into the plug or soldered in somehow might break and then I have a problem. With the Duex now allowing 5V endstops I could omit the resistor and just use one of those native ports.

                            For what it's worth I soldered and crimped the resistor in my end-stop connector just to make absolutely sure it's well connected.

                            1 Reply Last reply Reply Quote 0
                            • deckingmanundefined
                              deckingman
                              last edited by

                              Just curious as to how accurate this BL touch thing is for homing. I currently use DC42s excellent probe which works fine but the slight issue I have is that I have 3 pieces of glass with different surface coatings that I swap between. So if I go from say, plain glass with 3DLAC to glass with blue tape, I have to edit my config.g to change the Z offset for that particular surface. It occurs to me that the BL touch might negate the need to do that. Is that reasonably assumption?

                              BTW, I've managed to build my machine such that the bed is both flat and level and stays that way, so I have no need to compensate for level or flatness (although it is nice to use the probe to check from time to time). It's just Z homing with different surface materials that I'm interested in.

                              Ian
                              https://somei3deas.wordpress.com/
                              https://www.youtube.com/@deckingman

                              1 Reply Last reply Reply Quote 0
                              • T3P3Tonyundefined
                                T3P3Tony administrators
                                last edited by

                                Ian

                                How about a black sticker at the corner of each bed plate - be out of the way for nearly every print and should give the same result?

                                (sorry to hijack the bl touch thread!)

                                www.duet3d.com

                                1 Reply Last reply Reply Quote 0
                                • deckingmanundefined
                                  deckingman
                                  last edited by

                                  @T3P3Tony:

                                  Ian

                                  How about a black sticker at the corner of each bed plate - be out of the way for nearly every print and should give the same result?

                                  (sorry to hijack the bl touch thread!)

                                  Tony - that's a damned good idea - so simple! My initial reaction was that it wouldn't work with blue tape due to the thickness of the tape itself, but as long as the black sticker is on top of the tape (or any other material) then of course it will work. Brilliant! Thanks

                                  Ian
                                  https://somei3deas.wordpress.com/
                                  https://www.youtube.com/@deckingman

                                  1 Reply Last reply Reply Quote 0
                                  • W3DRKundefined
                                    W3DRK
                                    last edited by

                                    @deckingman:

                                    Just curious as to how accurate this BL touch thing is for homing.

                                    Antclabs claims a standard deviation of at least 0.01mm–apparently dependent on the probing speed due to the way hall-effect sensors work. I haven't had time to do more than about a dozen prints on this machine since fitting it with the BLTouch, but so far it's been working great and I haven't needed to adjust the Z offset since the initial setup. Perfect first layers every time.

                                    1 Reply Last reply Reply Quote 0
                                    • StephenRCundefined
                                      StephenRC
                                      last edited by

                                      @deckingman:

                                      I currently use DC42s excellent probe which works fine but the slight issue I have is that I have 3 pieces of glass with different surface coatings that I swap between. So if I go from say, plain glass with 3DLAC to glass with blue tape, I have to edit my config.g to change the Z offset for that particular surface.

                                      Use a macro to set the z offset. I have one for pla and another for petg. The two different filaments need a different z0 setting to get it to stick properly.

                                      1 Reply Last reply Reply Quote 0
                                      • Treitoundefined
                                        Treito
                                        last edited by

                                        Did you directly connect the Servo to Pin21? Does this PIN provide 5 volts or would I need some sort of diode?

                                        1 Reply Last reply Reply Quote 0
                                        • Jdn-zaundefined
                                          Jdn-za
                                          last edited by

                                          Just ordered myself a bltouch and will be adding it to my duet 0.8.5, thanks for documenting the install mate

                                          1 Reply Last reply Reply Quote 0
                                          • Sniffleundefined
                                            Sniffle
                                            last edited by

                                            W3DRK, just curious, does each successful probe actually reflect in the web interface for you? I have mine setup nd everything is working but to test before i have a bed crash i deployed the probe and manually actuated the pin maybe 1 in 10 seems to actually register in the interface though.

                                            just to make sure i slowed my manual testing speed way down but still had several swipes that werent displayed on the interface.

                                            on my meter my resistor came out to 241ohms so it "should" signal ok…

                                            1 Reply Last reply Reply Quote 0
                                            • First post
                                              Last post
                                            Unless otherwise noted, all forum content is licensed under CC-BY-SA