problem with the Mesh?second print start in the air
-
I dont have touch The homeall.g
Do i need to change something in homeall.g ?
this is my homeall.g
; homeall.g
; called to home all axes
;
; generated by RepRapFirmware Configuration Tool v2 on Thu Apr 11 2019 17:51:12 GMT+0200 (Mitteleuropäische Sommerzeit)
G91 ; relative positioning
G1 Z5 F6000 S2 ; lift Z relative to current position
G1 S1 X-258 Y-235 F1800 ; move quickly to X and Y axis endstops and stop there (first pass)
G1 X5 Y5 F6000 ; go back a few mm
G1 S1 X-258 Y-235 F360 ; move slowly to X and Y axis endstops once more (second pass)
G90 ; absolute positioning
G1 X10 Y10 F6000 ; go to first bed probe point and home Z
G30 ; home Z by probing the bed; Uncomment the following lines to lift Z after probing
;G91 ; relative positioning
;G1 S2 Z5 F100 ; lift Z relative to current position
;G90 ; absolute positioning -
What firmware version are you using?
What do you have in your slicer start and end gcode?
-
running a G28 will clear your bed mesh.
if you want to use the stored heightmap you will need to run G29 S1 after every G28 -
Does g28 clear the mesh? I didn't think it does. But I'm really not sure come to think of it.
-
@phaedrux said in problem with the Mesh?second print start in the air:
Does g28 clear the mesh? I didn't think it does. But I'm really not sure come to think of it.
You are right it does not. i just checked.
I must have confused it with marlin where it does. -
@lui2004
nevertheless you need a G29 S1 somewhere to load the mesh after powering up your printer. -
Hi
The heightmap ist Stored i can open it in my sd-card.
Do i need do load G29 S1 every Print i started?if yes i dont have do it
-
@lui2004
no but it is a good idea to do so.
it is just a command and does not take up time. -
Ok i will give it a try
Or i insert the gcode in my bed.g to load automatic
-
Or put it in your Slicer 'Start GCode', easiest way I find.
-
I have G29 S1 at the end of my config.g that way it's loaded every time on startup.
-
so the first print after mesh works perfectly but when i start the second the nozzle is to high
i have try to send beofor i start the second print G29 S1 but always the nozzle to high
Firmwarename: RepRapFirmware for Duet 2 WiFi/Ethernet
Firmware Elektronik: Duet WiFi 1.02 or later
Firmware Version: 2.02(RTOS) (2018-12-24b1)
WiFi Server Version: 1.22
Web Interface Version: 1.22.6i hope you can help to solve it
-
you do home before each print?
-
yes in my slicer is this starting code
G28 ; home all axes
-
@lui2004 what is at the end of your files that the slicer is putting in there?
-
I have only G28 i my starting code nothing else
-
do check with m122 that mesh bed leveling is still active.
-
@veti said in problem with the Mesh?second print start in the air:
m122
seems active
Bed compensation in use: mesh
Bed probe heights: -0.052 -0.028 0.000 0.000 0.000 -
Are you able to reproduce this problem without doing an actual print? Or with a "print" comprising just a few lines of GCode taken from a real print?
-
do i need to post gcode from a print ?
