XYZ carriage rise without reason

MrOppip

@fcwilt said in XYZ carriage rise without reason:

@MrOppip said in XYZ carriage rise without reason:

@fcwilt said in XYZ carriage rise without reason:

Hi,

Did you verify that the cables to the extruder motors are good?

Frederick

The motor and cable works well because I tried to connect it to x driver.

I read that you tried the X,Y motors with the E0,E1 drivers. I missed where you tried the extruder motor with the X driver.

When trying to extrude via DWC do you have a tool selected?

Frederick

it was written in the previous post

sure, otherwise the extrusion and protrusion button is disabled

Veti

can you tell us step by step how you are trying to extrude? every button you press, every command you issue.

MrOppip

@Veti said in XYZ carriage rise without reason:

can you tell us step by step how you are trying to extrude? every button you press, every command you issue.

first method:
power on duet
home all
activated heater
heated 200 °
in "extruder control" pressed extrude
then retract.

second method:
power on duet
activated heater
in "gcode console" given command M302 P1
then G1 E50
then G1 E-50

nothing moves

Veti

can you verify with a multimeter that the phases on the extruder stepper are correct.
i.e. one phase for red and blue and one for green and black.

fcwilt

@MrOppip

I don't see where you selected the tool.

Frederick

MrOppip

@fcwilt
activated the heater means the same as selected the tool.

@Veti
yes is the first thing I checked to run it correctly.
I found that my hardware is perfect because I loaded the Creality Ender 3 Pro predefined configuration from the RepRapFirmware Configuration Tool and the extruder works.

so there's something in myFW that doesn't make the extruder go.

I have the BLTouch, connected to the heater 3 (disabled as in the tutorials).
does it interfere in any way?

in the meantime, thanks for the support

fcwilt

@MrOppip said in XYZ carriage rise without reason:

@fcwilt
activated the heater means the same as selected the tool.

Hmm...

I cannot check right now but I'm pretty sure a tool can have it's heater in the standby state without the tool being active.

Frederick

Veti

@MrOppip said in XYZ carriage rise without reason:

I have the BLTouch, connected to the heater 3 (disabled as in the tutorials).
does it interfere in any way?

its shouldnt, but its an easy check. comment the line and try it.

do you have a config-overwrite? because you have a M501 in your config.

please post the config where it was working.

MrOppip

@Veti said in XYZ carriage rise without reason:

do you have a config-overwrite? because you have a M501 in your config.

I'm not sure if it's useful. I had enabled it along with the ability to save the print in the event of a blackout.

please post the config where it was working.

config Ender.g

checking it I saw that:
; Tools
M563 P0 D0 H1 F0

in my CR10 file config D0 is not there.

I don't know why the online configurator doesn't create it.

can it be the cause? I haven't had time to try yet.

Veti

yes
If there is no 'D' field the tool has no drives.

MrOppip

@Veti said in XYZ carriage rise without reason:

yes
If there is no 'D' field the tool has no drives.

ok! sorry for the delay but I checked only now.
the problem was just that "D" missing.
now everything works as it should.

Thanks for your help.