Help: Temp Sensors and Homing Issues

94118

Panel still states connecting, will be changing the hotend heater and thermistor to a US made 24v 40W Heater and an NTC Thermistor to replace the K Thermalcouple

94118

Attn: Moderators

2 options

Either tell me how to fix my Paneldue
Request RMA for paneldue so that i may get it excahnged with PrintedSolid.

Phaedrux

@94118 said in Help: Temp Sensors and Homing Issues:

Attn: Moderators

2 options

Either tell me how to fix my Paneldue

Request RMA for paneldue so that i may get it excahnged with PrintedSolid.

Please restate the problem with the PanelDue.
What paneldue firmware version are you using?
How do you have it wired?
If you are using the ribbon cable, have you tried the 4 wire cable, and vice versa.
Have you tested continuity on the wires?
What baud rate is set in the PanelDue settings menu?
What baud rate are you using in your config?

94118

Not Connecting, Panel firmware ver1.23, both 4 pin wire and ribbon cable , Baud rate set 56700 for both.

Phaedrux

Have you updated the firmware yourself, or is it still as is out of the box?

Did it connect initially?

I would try re-flashing the firmware
https://duet3d.dozuki.com/Wiki/PanelDue_Firmware_update

94118

yes it did connect initially, and yes i did reflash the firmware myself with Bossa i have tried reflashing the firmware may times and have not gotten anywhere

T3P3Tony

@94118 what error do you get when you flash the firmware?

94118

I was getting no errors when i did this. it now states connecting.

dc42

If it says Connecting, the PanelDue firmware is almost certainly OK.

Go to the Setup page on PanelDue, check the baud rate setting there is 57600
Connect to the Duet via YAT or DWC and send M575 P1. Check that it also reports 57600 baud.

94118

Here is the results:
console.txt and this after i checked that the board and the panel are on the same baud speed setting. how would i issue a restart or reset of the board and panel.

dc42

Your M575 P1 setting is correct, so it should be able to communicate with the PanelDue assuming that the PanelDue is set to 57600 in the Settings page.

Next step is to check whether the Duet is receiving data form PanelDue. Connect to the Duiet via YAT and send M111 S1 P3. It should report that debugging enabled for the GCodes module. It will then echo all received GCode commands in the YAT main window. Do you see any messages beginning "aux: M408" ? You should get those as long as the PanelDue is not on the Setup page.

If you are using the ribbon cable, make sure it is plugged into the CONN_SD socket on the Duet. Not CONN_LCD.

94118

Here is the result from DWC YAT is not giving me connection options for comm ports. YAT is to difficult
console.txt

Phaedrux

@94118 said in Help: Temp Sensors and Homing Issues:

YAT is to difficult
console.txt

M111 S1 P3 has enabled debugging messages to steam to the USB port. You will need either YAT or some other USB terminal to view it.

94118

having problems with USB terminal emulators they do not see anything beyond comm 1

Phaedrux

Does the duet show up as a device in device manager?

94118

NO it does not

Phaedrux

But you are able to connect to the duet via the network and DWC?

Phaedrux

When you connect the Duet via USB does it make the usb device detected sound?

Phaedrux

Have you followed this part of the getting connected guide?
Have you installed the drivers?
It also covers YAT.

https://duet3d.dozuki.com/Guide/1.)+Getting+Connected+to+your+Duet/7#s5

94118

Duet to the network Yes. Duet to USB NO Sound from windows. Unable to install duet drivers cause DM states not compatible with 64bit