Cura Script to Automatically Probe Only Printed Area

DK90

@tcj said in Cura Script to Automatically Probe Only Printed Area:

C:\Users\Dominic\AppData\Local\Programs\Python\Python36-32\python.exe "C:\Program Files\Prusa3D\PrusaSlicer\duet3d_automesh.py"

Oh thank you now ot works
but wehn i start the print, there is now mesh leveling ....
where is my error?

Start G-Code

M83  ; extruder relative mode
M140 S[first_layer_bed_temperature] ; set bed temp

M190 S[first_layer_bed_temperature] ; wait for bed temp



; For automesh
     M557 TBD  ; parameters will be set automatically
     G28  ;home
     ;G29 S1 P"heightmap.csv"; Hoehenkarte Laden

M109 S[first_layer_temperature] ; wait for extruder temp
;G29 S1 P"heightmap.csv"; Hoehenkarte Laden


; Reinigungs Fahrt
G1 X-3.0 Y-10 F1500.0 ; go outside print area
G92 E0.0
G1 Z0
G1 E8 ; Purge Bubble
G1 X60.0 E9.0  F1000.0 ; intro line
G1 X100.0 E12.5  F1000.0 ; intro line
G92 E0.0

G-Code layer change setting

; Automesh: begin layer [layer_num]

tcj

@DK90 said in Cura Script to Automatically Probe Only Printed Area:

but wehn i start the print, there is now mesh leveling ....

and it never will without G29

this is a part of my start sequence

M140 S[first_layer_bed_temperature]
M104 S[first_layer_temperature]
M116; wait for temperatures to be reached
 
; For automesh
M557 TBD  ; parameters will be set automatically
G28 ; home
G29 ; mesh

DK90

oh yes that sounds good....that was my mistake...:D Thank you

zapta

@DK90, if you use panel due and prusaslicer (and maybe cura, didn't try), try to enable Support Remaining Time in the Printer Settings | General, tab. This will include M73 time markers in the gcode that which cause the post processing script to show remaining hours and minutes in the Standby fields of Panel Duet (ignore the '-' prefix).

This time estimation is much more consistent than the ones provided by Duet.

DK90

@zapta Thank you for the info. I will try it. That sound good.

tcj

@zapta I'm sorry to say that, but it does not work properly yet.
The script gives

M557 X-10:32 Y-10:32 P3:3

where it should deliver

M557 X-32:32 Y-32:32 P3:3

for a testcube in the middle of the bed with some mm of skirt

total dimensions +/- 21.xx mm

OwenD

@tcj what are your probe offsets?

CCS86

Probe offsets wouldn't matter.

Posting the gcode would be helpful though.

zapta

@tcj, try to run the script manually and see what it prints. To do that, run it from command line with the same arguments you have in the slicer and also add the name of the gcode file at the end of the command line.

When I run it I get prints like this

MESHABLE area: 30.0:280.0,30.0:280.0
Opening gcode file: /var/folders/dt/1t1sf6d574d3l023pknh_754000cbj/T/.PrusaSlicer.upload.7e0e-12b6-1a76-0282
Read 83648 lines
Parsing state = ParsingState.WAITING_FOR_LAYER1
;Automesh: begin layer 0
Parsing state = ParsingState.IN_LAYER1
;Automesh: begin layer 1
Parsing state = ParsingState.LAYER1_DONE
First layer print areas: 92:189,131:210
printArea: 92:189,131:210
Will use 4 x 3 mesh points
Marker: M557 TBD  ; marker for automesh script
Inserted: M557 X82:199 Y121:220 P4:3

(if you prefer, post your gcode file and command line parameters and I can test it here)

tcj

C:\Users\tcj-a>C:\Users\tcj-a\AppData\Local\Programs\Python\Python38-32\python.exe C:\Users\tcj-a\Documents\scripts\duet3d_automesh.py C:\Users\tcj-a\Desktop\single_wall_box.gcode --meshable=-185:185,-185:185
MESHABLE area: -185.0:185.0,-185.0:185.0
Opening gcode file: C:\Users\tcj-a\Desktop\single_wall_box.gcode
Read 7472 lines
Parsing state = ParsingState.WAITING_FOR_LAYER1
; Automesh: begin layer 0
Parsing state = ParsingState.IN_LAYER1
; Automesh: begin layer 1
Parsing state = ParsingState.LAYER1_DONE
First layer print areas: 0:22,12:22
printArea: 0:22,12:22
Will use 3 x 3 mesh points
Marker: M557 TBD  ; parameters will be set automatically
Inserted: M557 X-10:32 Y2:32 P3:3

single_wall_box.gcode

obviously the script does not handle negative numbers as needed, because the first layer print area is -22:-22, 22:22

zapta

@tcj, thanks for the example and for your patient.

I made a fix and am now getting the output below. The problem existed in the original code posted in this thread, parsing only non negative x and y values.

MESHABLE area: -100.0:100.0,-100.0:100.0
Opening gcode file: single_wall_box.gcode
Read 7472 lines
Parsing state = ParsingState.WAITING_FOR_LAYER1
; Automesh: begin layer 0
Parsing state = ParsingState.IN_LAYER1
; Automesh: begin layer 1
Parsing state = ParsingState.LAYER1_DONE
First layer print areas: -22:22,-22:22
printArea: -22:22,-22:22
Will use 3 x 3 mesh points
Marker: M557 TBD  ; parameters will be set automatically
Inserted: M557 X-32:32 Y-32:32 P3:3

https://github.com/zapta/misc/blob/master/duet3d_automesh/duet3d_automesh.iml

tcj

@zapta thank you

Baenwort

@zapta said in Cura Script to Automatically Probe Only Printed Area:

@tcj, thanks for the example and for your patient.

I made a fix and am now getting the output below. The problem existed in the original code posted in this thread, parsing only non negative x and y values.

https://github.com/zapta/misc/blob/master/duet3d_automesh/duet3d_automesh.iml

Does this bring it closer to working for Delta's? Or at least probing a square area of the circular bed?

zapta

@Baenwort, what are the special requirements for delta compared to a cartesian?

The current script finds the bounding rectangle of the first layer's print (negative numbers are ok) and generates a M557 command with X and Y ranges and number of probe points.

In case of a delta, the bounding rectangle can have points outside the round print area but I presume the duet will ignore them.

Edit: for delta, if objects are placed in the center, it's possible to compute the radius from (0, 0) and issue a M557 with a R param.

Red Sand Robot

I'm also having an issue when getting the post processing script to run. I am getting this:

Post-processing script C:\Users\Jack\AppData\Local\Programs\Python\Python38-32\python.exe "C:\Program Files\PrusaSlicer-2.2.0+win64-202003211145\PrusaSlicer-2.2.0+win64-202003211145\duet3d_automesh.py" on file C:\Users\Jack\Documents\3D Printing\Stuff\Flex Tube Support.gcode failed.
Error code: 1

Any ideas on what I may be doing wrong?
This is my full start gcode script:

M82 ;absolute extrusion mode
G21 ;metric values
G90 ;absolute positioning
M82 ; set extruder to absolute mode
M107 ;start with the fan off
G29 S2; clears existing bed heightmap

; For automesh
M557 TBD  ; parameters will be set automatically
G28; home all

G32; motorized gantry plane correction
G32;
G32; Repeated 3 times to ensure its correct

G29  Mesh Bed compensation 

G1 Z20 F6000 ;move the platform down 15mm
G1 F100 E9 ;extrude 9mm of feed stock
G92 E0 ;zero the extruded length

OwenD

@Red-Sand-Robot
Double check the content of the script.
I just tried yesterday and was getting the same error.
The first time I downloaded, I right clicked the link and selected "download link" or some such.
Problem was it downloaded the whole HTML page, not just the python script. (DOH!)
After copying and pasting just the script content it worked fine.

zapta

@Red-Sand-Robot, I would suggest to first run it manually from the command line. It will give you more information on what's going on. (after verifying that the script download is ok per OwenD's suggestion)

Red Sand Robot

@zapta Command line? As in my computer or PrusaSlicer? Sorry, the programming side of things isn't my forte.

zapta

@Red-Sand-Robot, it seems that you work on windows. I meant commands types in the DOS window. I don't have here a Windows computer but others here may be able to explain it better.

https://www.lifewire.com/how-to-open-command-prompt-2618089

Red Sand Robot

@zapta Yes, I work on windows. Haven't made the jump to attempt to learn Linux or associated stuff yet though I suppose I should if I ever want to use a RPI for anything useful.

When I ran the script from the command prompt window, I received this output:

C:\Users\Jack>AppData\Local\Programs\Python\Python38-32\python.exe "C:\Users\Jack\Documents\3D Printing\PrusaSlicerScript\duet3d_automesh.py"
usage: duet3d_automesh.py [-h] [--meshable MESHABLE] [--margin MARGIN] [--spacing SPACING]
                          [--min_points {2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49}]
                          [--max_points {2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49}]
                          [--first_layer_start FIRST_LAYER_START] [--first_layer_end FIRST_LAYER_END]
                          file_path
duet3d_automesh.py: error: the following arguments are required: file_path

Does that look like it is functioning correctly? I'm guessing that the file_path argument is talking about the .gcode file, but if not that would indicate an error with how I'm calling the script from what I understand.