Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    Duet 3 v1.0 Fault on SD slot

    Scheduled Pinned Locked Moved
    Duet Hardware and wiring
    5
    24
    620
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • T3P3Tonyundefined
      T3P3Tony administrators
      last edited by

      please connect over USB (with a terminal like YAT) with an SD card in the socket and send M122

      www.duet3d.com

      Carloundefined 1 Reply Last reply Reply Quote 0
      • Carloundefined
        Carlo @T3P3Tony
        last edited by

        @T3P3Tony

        Hi Tony see below thanks.

        M122
        === Diagnostics ===
        RepRapFirmware for Duet 3 MB6HC version 3.1.1 running on Duet 3 MB6HC v0.6 or 1.0 (SBC mode)
        Board ID: 08DJM-956L2-G43S8-6J9DL-3SD6M-1S3UF
        Used output buffers: 1 of 40 (13 max)
        === RTOS ===
        Static ram: 154604
        Dynamic ram: 161360 of which 20 recycled
        Exception stack ram used: 308
        Never used ram: 76924
        Tasks: NETWORK(ready,1972) HEAT(blocked,1416) CanReceiv(suspended,3820) CanSender(suspended,1488) CanClock(blocked,1436) TMC(blocked,204) MAIN(running,4528) IDLE(ready,76)
        Owned mutexes:
        === Platform ===
        Last reset 00:02:56 ago, cause: reset button
        Last software reset at 2020-08-10 18:57, reason: User, spinning module GCodes, available RAM 76172 bytes (slot 1)
        Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0444a000 BFAR 0x00000000 SP 0xffffffff Task MAIN
        Error status: 0
        MCU temperature: min 39.1, current 39.7, max 39.8
        Supply voltage: min 23.9, current 24.2, max 24.3, under voltage events: 0, over voltage events: 0, power good: yes
        12V rail voltage: min 12.1, current 12.1, max 12.2, under voltage events: 0
        Driver 0: standstill, reads 20356, writes 0 timeouts 0, SG min/max not available
        Driver 1: standstill, reads 20356, writes 0 timeouts 0, SG min/max not available
        Driver 2: standstill, reads 20356, writes 0 timeouts 0, SG min/max not available
        Driver 3: standstill, reads 20356, writes 0 timeouts 0, SG min/max not available
        Driver 4: standstill, reads 20356, writes 0 timeouts 0, SG min/max not available
        Driver 5: standstill, reads 20356, writes 0 timeouts 0, SG min/max not available
        Date/time: 1970-01-01 00:00:00
        Slowest loop: 0.34ms; fastest: 0.14ms
        === Storage ===
        Free file entries: 10
        SD card 0 detected, interface speed: 12.5MBytes/sec
        SD card longest read time 0.0ms, write time 0.0ms, max retries 0
        === Move ===
        Hiccups: 0(0), FreeDm: 375, MinFreeDm: 375, MaxWait: 0ms
        Bed compensation in use: none, comp offset 0.000
        === MainDDARing ===
        Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1
        === AuxDDARing ===
        Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1
        === Heat ===
        Bed heaters = -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
        === GCodes ===
        Segments left: 0
        Movement lock held by null
        HTTP is idle in state(s) 0
        Telnet is idle in state(s) 0
        File is idle in state(s) 0
        USB is ready with "M122" in state(s) 0
        Aux is idle in state(s) 0
        Trigger* is idle in state(s) 0 0, running macro
        Queue is idle in state(s) 0
        LCD is idle in state(s) 0
        SBC is idle in state(s) 0
        Daemon* is idle in state(s) 0 0, running macro
        Aux2 is idle in state(s) 0
        Autopause is idle in state(s) 0
        Code queue is empty.
        === Network ===
        Slowest loop: 1.42ms; fastest: 0.01ms
        Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions Telnet(0), 0 sessions
        HTTP sessions: 0 of 8

        • Ethernet -
          State: disabled
          Error counts: 0 0 0 0 0
          Socket states: 0 0 0 0 0 0 0 0
          === CAN ===
          Messages sent 0, longest wait 0ms for type 0
          === Linux interface ===
          State: 0, failed transfers: 0
          Last transfer: 140774ms ago
          RX/TX seq numbers: 0/1
          SPI underruns 0, overruns 0
          Number of disconnects: 0
          Buffer RX/TX: 0/0-0
          ok

        Cheers
        C

        1 Reply Last reply Reply Quote 0
        • T3P3Tonyundefined
          T3P3Tony administrators
          last edited by

          @Carlo said in Duet 3 v1.0 Fault on SD slot:

          SD card 0 detected, interface speed: 12.5MBytes/sec

          Although that is not a great speed it does appear to be working. please post your config.g thats on the SD card.

          Its saying SBC mode so is the Pi connected? I wonder if you get a different response with the Pi not connected.

          www.duet3d.com

          1 Reply Last reply Reply Quote 0
          • Carloundefined
            Carlo
            last edited by

            Tony the Pi is not connected
            and it was working yesterday in stand alone mode

            Config.g
            ; Configuration file for Duet 3 (firmware version 3)
            ; executed by the firmware on start-up
            ;
            ; generated by RepRapFirmware Configuration Tool v2.1.8 on Mon May 25 2020 14:05:35 GMT+0100 (British Summer Time)

            ; General preferences
            G90 ; send absolute coordinates...
            M83 ; ...but relative extruder moves
            M550 P"Duet 3" ; set printer name
            M665 L440.47:440.47:440.47 R234.553 H410.523 B185.0 X 0.265°, Y 0.181°, Z 0.000° ; Set delta radius, diagonal rod length, printable radius and homed height
            M666 X-0.00 Y0.00 Z-0.00 A0.00 B0.00 ; put your endstop adjustments here, or let auto calibration find them
            ;M665 L438.767:438.767:438.767
            ; Network
            M552 P192.168.0.25 S1 ; enable network and set IP address
            M553 P255.255.255.0 ; set netmask
            M554 P192.168.0.254 ; set gateway
            M586 P0 S1 ; enable HTTP
            M586 P1 S0 ; disable FTP
            M586 P2 S0 ; disable Telnet

            ; Drives
            M569 P0.0 S0 ; physical drive 0.0 goes backwards
            M569 P0.1 S0 ; physical drive 0.1 goes backwards
            M569 P0.2 S0 ; physical drive 0.2 goes backwards
            M569 P0.3 S1 ;G5 ; physical drive 0.4 forwards for G5 flex
            M584 X0.0 Y0.1 Z0.2 E0.3 ; set drive mapping CHANGE G5 0.4G
            M350 E8 I0 ;G5 ; G5 configure 8 microstepping interpolation off
            M350 X16 Y16 Z16 I1 ; configure microstepping with interpolation
            M92 X160.00 Y160.00 Z160.00 E1900.00 ; G5 set steps per mm G5 1900
            M566 X1200.00 Y1200.00 Z1200.00 E6.00 ; G5 set maximum instantaneous speed changes (mm/min) 6
            M203 X12000.00 Y12000.00 Z12000.00 E2400.00 ; set maximum speeds (mm/min)
            M201 X1200.00 Y1200.00 Z1200.00 E120.00 ; set accelerations (mm/s^2)
            M906 X1050 Y1050 Z1050 E270 I50 ; set motor currents (mA) and motor idle factor in per cent
            M84 S45 ; Set idle timeout

            ; Axis Limits
            M208 Z-0.3 S1 ; set minimum Z

            ; Endstops
            M574 X2 S1 P"io4.in" ; configure active-high endstop for high end on X via pin io4.in
            M574 Y2 S1 P"io1.in" ; configure active-high endstop for high end on Y via pin io1.in
            M574 Z2 S1 P"io2.in" ; configure active-high endstop for high end on Z via pin io2.in

            ; Z-Probe
            M558 P8 R0.8 C"io3.in+io3.out" H5 F1200 T5000 ; set Z probe type to effector and the dive height + speeds
            G31 P500 X0 Y0 Z-0.12 ; set Z probe trigger value, offset and trigger height
            M557 R160 S20 ; define mesh grid

            ; Heaters
            M308 S0 P"temp0" Y"thermistor" T100000 B3950 ;B3950 C0 R4700 configure sensor 0 as thermistor on pin temp0
            M950 H0 C"out0" T0 ; create bed heater output on out0 and map it to sensor 0
            M143 H0 S120 ; set temperature limit for heater 0 to 120C
            M307 H0 A108.2 C457.9 D0.5 S1.00 V24.1 B0 ; disable bang-bang mode for the bed heater and set PWM limit
            M140 H0 ; map heated bed to heater 0
            M308 S1 P"spi.cs0" Y"rtd-max31865" ; configure sensor 1 as thermocouple via CS pin spi.cs0
            M950 H1 C"out1" T1 ; create nozzle heater output on out1 and map it to sensor 1
            M143 H1 S450 ; set temperature limit for heater 1 to 450C
            M307 H1 A512.3 C269.6 D3.6 S1.00 V24.0 B0 ; disable bang-bang mode for heater and set PWM limit

            ; Fans
            M950 F0 C"out9" Q250 ; create fan 0 on pin out9 and set its frequency
            M106 P0 S0 H-1 C"Part Cooler" ; set fan 0 value. Thermostatic control is turned off
            M950 F1 C"out7" Q250 ; create fan 1 on pin out7 and set its frequency
            M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on
            ;M950 F2 C"out8" Q100 ; set fan 2 value. Thermostatic control is turned off
            ;M106 P0 S0 I0 F500 H-1 L0.35 B2.5 ;Berd air pump settings

            ; Tools
            M563 P0 S"E3D Brass 0.4" D0 H1 F0:2 ; define tool 0
            G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
            G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

            ; Custom settings
            ;Retraction settings
            M207 S1.50 F900 T550 Z0.3 ;G5 ; G5 retraction setting

            ;MCU Temp
            M912 P0 S-1.8 ; adjust MCU temp for correction at ambient
            ; Miscellaneous
            ;M501 ; load saved parameters from non-volatile memory

            Cheers
            C

            T3P3Tonyundefined 1 Reply Last reply Reply Quote 0
            • T3P3Tonyundefined
              T3P3Tony administrators @Carlo
              last edited by

              @Carlo Thanks

              So when connected in YAT, with the Ethernet plugged in if you send

              M552 P192.168.0.25 S1
              

              Does it work as expected?

              Another test is to send M665 with no parameters and see if the correct ones are displayed back.

              Basically trying to confirm if the SD card it being read or not.

              Laos if you have another SD card it would be worth testing that.

              www.duet3d.com

              Carloundefined 1 Reply Last reply Reply Quote 0
              • Carloundefined
                Carlo @T3P3Tony
                last edited by Carlo

                @T3P3Tony

                Response from YAT

                M552 P192.168.0.25 S1
                ok
                Ethernet running, IP address = 192.168.0.25

                M665
                Error: M665: M665 parameters do not apply to Cartesian kinematics
                ok

                Still can't connect:
                Your Duet rejected the HTTP request: page not found
                Check that the SD card is mounted and has the correct files in its /www folder

                First thing I tried of the usual thing was swap the card with a backup of all the folders
                Before I re-flashed the firmware

                1 Reply Last reply Reply Quote 0
                • Phaedruxundefined
                  Phaedrux Moderator
                  last edited by

                  It definitely seems like it's not reading the SD card. Not executing the config.g and can't read the /www folder.

                  Can you try sending M22 followed by M21? This should unmount and remount the SD card.

                  Also M122 P104, which should try to measure the write speed of the SD card.

                  Z-Bot CoreXY Build | Thingiverse Profile

                  Carloundefined 1 Reply Last reply Reply Quote 0
                  • Carloundefined
                    Carlo @Phaedrux
                    last edited by Carlo

                    @Phaedrux said in Duet 3 v1.0 Fault on SD slot:

                    M22

                    Hi,

                    Yat output of M21/M22

                    M22
                    SD card 0 may now be removed
                    ok
                    M21
                    Error: M21: Cannot initialise SD card 0: Card is unusable
                    ok

                    I've tried a third card which this is output against, weirdly the SD slot is now latching 1st time?.

                    M122 P104
                    Error: Failed to create folder 0:/gcodes in path 0:/gcodes/test.tst
                    Error: M122: Failed to create file
                    ok

                    Cheers
                    C

                    1 Reply Last reply Reply Quote 0
                    • Phaedruxundefined
                      Phaedrux Moderator
                      last edited by

                      When and where was the board purchased? There seems to be a fault in the SD card slot.

                      Can you post close up photos of the slot insides and the solder tabs?

                      Z-Bot CoreXY Build | Thingiverse Profile

                      Carloundefined 1 Reply Last reply Reply Quote 0
                      • Carloundefined
                        Carlo @Phaedrux
                        last edited by

                        @Phaedrux

                        Yeah Pic to follow
                        08/04/20 E3D

                        Cheers
                        C

                        1 Reply Last reply Reply Quote 0
                        • Phaedruxundefined
                          Phaedrux Moderator
                          last edited by

                          Sorry, is that August 4th or April 8th? Not that it matters, either are within 6 months.

                          You can contact E3D and initiate a warranty exchange. Use this thread as authorization. I'm not sure what the current Duet3 stock status is due to the current manufacturing issue with driver diodes, so there may be a delay on replacement. At least in the meantime you can use SBC mode.

                          Z-Bot CoreXY Build | Thingiverse Profile

                          Carloundefined 1 Reply Last reply Reply Quote 0
                          • Carloundefined
                            Carlo @Phaedrux
                            last edited by

                            @Phaedrux
                            LoL no I can't use SBC mode it has never worked "under investigation"

                            IMG_1617.jpg IMG_1611.jpg
                            Best I can get on my phone

                            I can't see anything obvious with the slot or pads?

                            Cheers
                            C

                            1 Reply Last reply Reply Quote 0
                            • Phaedruxundefined
                              Phaedrux Moderator
                              last edited by

                              Right: https://forum.duet3d.com/topic/16191/duet3-pi-dwc-freezing/31?_=1597246408031

                              All the more reason to swap it out. Something is amiss.

                              Z-Bot CoreXY Build | Thingiverse Profile

                              Carloundefined 1 Reply Last reply Reply Quote 0
                              • Carloundefined
                                Carlo @Phaedrux
                                last edited by Carlo

                                @Phaedrux
                                April

                                Thanks as always appreciate your help.

                                C

                                1 Reply Last reply Reply Quote 0
                                • Phaedruxundefined
                                  Phaedrux Moderator
                                  last edited by

                                  It sounds like FW 3.2 beta1 is arriving shortly (maybe this week), if you still have the board when it lands, perhaps you can test it to see if it has an effect on your other SBC issue.

                                  Z-Bot CoreXY Build | Thingiverse Profile

                                  Carloundefined 1 Reply Last reply Reply Quote 0
                                  • Carloundefined
                                    Carlo @Phaedrux
                                    last edited by

                                    @Phaedrux

                                    E3D is out of stock so I'll keep hold until I've tested 3.2.1beta may be helpful.

                                    Cheers
                                    C

                                    1 Reply Last reply Reply Quote 0
                                    • Phaedruxundefined
                                      Phaedrux Moderator
                                      last edited by

                                      Do you happen to have a different pi to test SBC mode with?

                                      Z-Bot CoreXY Build | Thingiverse Profile

                                      Carloundefined 1 Reply Last reply Reply Quote 0
                                      • Carloundefined
                                        Carlo @Phaedrux
                                        last edited by

                                        @Phaedrux

                                        Yeah tested it with 3 Pi's 2x 4b and 1 3b+ all exactly the same result with nothing else attached and even tried a new 26 pin cable still the same.

                                        Carloundefined 1 Reply Last reply Reply Quote 0
                                        • Carloundefined
                                          Carlo @Carlo
                                          last edited by

                                          @Carlo
                                          The freezing I sorted by not using duetPi and just adding DSF to another distro but thats a far as I could get I could do everything but print ..just went nuts on the purge line or first move
                                          actually damaged my print bite sheet rammed the head in to the bed bent the heat break
                                          but same files Iv'e printed many time in stand alone

                                          1 Reply Last reply Reply Quote 0
                                          • A Former User?
                                            A Former User
                                            last edited by

                                            i didn't read the whole thread i'll admitt, but if you want to verify the individual parts that make up the connection between the pi and the duet this old-ish thread has a ton of information on where to go digging https://forum.duet3d.com/topic/15551/duet3-pi-dcs-is-unavailable-after-wiring-24v/119?_=1597267914698

                                            (and if not, disregard:)

                                            Carloundefined 1 Reply Last reply Reply Quote 1
                                            • First post
                                              Last post
                                            Unless otherwise noted, all forum content is licensed under CC-BY-SA