Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    Werid slicer problems

    Scheduled Pinned Locked Moved
    General Discussion
    5
    12
    463
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • nightmare90gtundefined
      nightmare90gt
      last edited by

      I have a werid problem. If I use prusaslicer the first layer is at the right height but with simplified3d is starts to high. What could cause this? I have checked settings no offsets are being added.

      1 Reply Last reply Reply Quote 0
      • A Former User?
        A Former User
        last edited by

        Share the starting g-code of both? S3D has to be doing something different

        1 Reply Last reply Reply Quote 0
        • nightmare90gtundefined
          nightmare90gt
          last edited by nightmare90gt

          simplified3d
          G28 ; home all axes
          G1 X5 Y10 Z0.2 F3000 ; get ready to prime
          G92 E0 ; reset extrusion distance
          G1 X160 E15 F600 ; prime nozzle
          G1 X180 F5000 ; quick wipe

          Prusaslicer
          M107
          M190 S60 ; set bed temperature and wait for it to be reached
          M104 S210 ; set temperature
          G28 ; home all axes
          G1 Z5 F5000 ; lift nozzle
          M109 S210 ; set temperature and wait for it to be reached
          G21 ; set units to millimeters
          G90 ; use absolute coordinates
          M82 ; use absolute distances for extrusion
          G92 E0

          Phaedruxundefined 1 Reply Last reply Reply Quote 0
          • JamesMundefined
            JamesM
            last edited by

            I think he means he wants you to share some of the actual gcode file you are printing and not just the start gcode. One thing to note is it is best to use relative extrusion and not absolute extrusion with the duet boards.

            nightmare90gtundefined 1 Reply Last reply Reply Quote 0
            • nightmare90gtundefined
              nightmare90gt @JamesM
              last edited by

              @JamesM what would relative gcode look like?

              1 Reply Last reply Reply Quote 0
              • Phaedruxundefined
                Phaedrux Moderator @nightmare90gt
                last edited by

                @nightmare90gt said in Werid slicer problems:

                G1 X5 Y10 Z0.2 F3000 ; get ready to prime

                Are you off by 0.2mm height?

                Post the a full sliced gcode from each so we can see how the start of the print and first layer plays out. The start gcode is part of it, but we need to see more.

                Relative extrusion versus absolute extrusion is a bit complex and unrelated to your problem here, but here's a break down that explains it well since it's worth knowing anyway.

                https://www.sublimelayers.com/2017/10/to-extruder-relative-or-not-to-extrude.html

                Z-Bot CoreXY Build | Thingiverse Profile

                1 Reply Last reply Reply Quote 0
                • nightmare90gtundefined
                  nightmare90gt
                  last edited by

                  I will verify tomorrow and report back.

                  1 Reply Last reply Reply Quote 0
                  • nightmare90gtundefined
                    nightmare90gt
                    last edited by

                    xyzCalibration_cube (Prusa).gcode xyzCalibration_cube (simp).gcode

                    simplified I have to adjust the baby set to .160mm to get a clean first layer.
                    ; Configuration file for Duet WiFi (firmware version 3)
                    ; executed by the firmware on start-up
                    ;
                    ; generated by RepRapFirmware Configuration Tool v3.1.4 on Fri Oct 02 2020 09:51:53 GMT+0200 (Central European Summer Time)

                    ; General preferences
                    G90 ; send absolute coordinates...
                    M83 ; ...but relative extruder moves
                    M550 P"Ender 5 Plus CoreXY" ; set printer name
                    M669 K1 ; select CoreXY mode

                    ; Network
                    M552 S1 ; enable network
                    M586 P0 S1 ; enable HTTP
                    M586 P1 S0 ; disable FTP
                    M586 P2 S0 ; disable Telnet

                    M671 X-20:370 Y150:150 S3.0 ; leadscrews at left (connected to Z) and right (connected to E2) of X axis

                    ; Drives
                    M569 P0 S0 ; physical drive 0 goes backwards
                    M569 P1 S0 ; physical drive 1 goes backwards
                    M569 P2 S0 ; physical drive 2 goes backwards
                    M569 P3 S1 ; physical drive 3 goes forwards
                    M569 P4 S1 ; physical drive 4 goes forwards
                    M569 P5 S0 ; physical drive 5 goes backwards
                    M584 X0 Y1 Z2:5 E3:4 ; set drive mapping
                    M350 X16 Y16 Z16 E16:16 I1 ; configure microstepping with interpolation
                    M92 X80.00 Y80.00 Z800.00 E415.00:415.00 ; set steps per mm
                    M566 X900.00 Y900.00 Z12.00 E120.00:120.00 ; set maximum instantaneous speed changes (mm/min)
                    M203 X6000.00 Y6000.00 Z180.00 E1200.00:1200.00 ; set maximum speeds (mm/min)
                    M201 X500.00 Y500.00 Z20.00 E250.00:250.00 ; set accelerations (mm/s^2)
                    M906 X1050 Y1050 Z800 E600:600 I30 ; set motor currents (mA) and motor idle factor in per cent
                    M84 S30 ; Set idle timeout

                    ; Axis Limits
                    M208 X0 Y0 Z0 S1 ; set axis minima
                    M208 X320 Y350 Z400 S0 ; set axis maxima

                    ; Endstops
                    M574 X1 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop
                    M574 Y1 S1 P"ystop" ; configure active-high endstop for low end on Y via pin ystop
                    M574 Z1 S2 P"zstop+e2stop" ; configure Z-probe endstop for low end on Z

                    ; Z-Probe
                    M950 S0 C"duex.pwm5" ; create servo pin 0 for BLTouch
                    M558 P9 C"^zprobe.in" H5 F300 T6000 ; set Z probe type to bltouch and the dive height + speeds
                    G31 P500 X30.814 Y17.505 Z1.663 ; set Z probe trigger value, offset and trigger height
                    M557 X50:320 Y15:350 S50 ; define mesh grid

                    ; Heaters
                    M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
                    M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
                    M307 H0 B1 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit
                    M140 H0 ; map heated bed to heater 0
                    M143 H0 S120 ; set temperature limit for heater 0 to 120C
                    M308 S1 P"e0temp" Y"thermistor" T500000 B4723 C1.19622e-7 ; configure sensor 1 as thermistor on pin e0temp
                    M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
                    M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
                    M308 S2 P"e1temp" Y"thermistor" T500000 B4723 C1.19622e-7 ; configure sensor 2 as thermistor on pin e1temp
                    M950 H2 C"e1heat" T2 ; create nozzle heater output on e1heat and map it to sensor 2
                    M307 H2 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit

                    ; Fans
                    M950 F0 C"fan0" Q20 ; create fan 0 on pin fan0 and set its frequency
                    M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
                    M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
                    M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on
                    M950 F2 C"fan2" Q500 ; create fan 2 on pin fan2 and set its frequency
                    M106 P2 S1 H2 T45 ; set fan 2 value. Thermostatic control is turned on

                    ; Tools
                    M563 P0 S"E0" D0 H1 F0 ; define tool 0
                    G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
                    G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
                    M563 P1 S"E1" D1 H2 F0 ; define tool 1
                    G10 P1 X0 Y0 Z0 ; set tool 1 axis offsets
                    G10 P1 R0 S0 ; set initial tool 1 active and standby temperatures to 0C

                    ; Custom settings
                    M591 D0 P5 C"e0_stop" R40:120 E3.0 S0 ; Duet3D laser sensor for extruder drive 0, connected to endstop input 3 (E0), tolerance 40 to 120%, 3mm comparison length, disabled
                    M591 D1 P5 C"e1_stop" R40:120 E3.0 S0 ; Duet3D laser sensor for extruder drive 1, connected to endstop input 4 (E1), tolerance 40 to 120%, 3mm comparison length, disabled

                    ; Miscellaneous
                    M575 P1 S1 B57600 ; enable support for PanelDue
                    M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss
                    M501 ; load stored settings
                    T0 ; select first tool

                    1 Reply Last reply Reply Quote 0
                    • nightmare90gtundefined
                      nightmare90gt
                      last edited by

                      This post is deleted!
                      1 Reply Last reply Reply Quote 0
                      • nightmare90gtundefined
                        nightmare90gt
                        last edited by

                        I changed both to relative and they both seem to be off by .160mm per baby stepping. I have tried raising and lowering the probe height but just doesn't seem to work.

                        1 Reply Last reply Reply Quote 0
                        • Phaedruxundefined
                          Phaedrux Moderator
                          last edited by

                          The gcode for each of those is completely different. Prusa slicer is using a first layer height of 0.35 and simplify is using 0.15. Simplify is using mesh compensation with G29, and Prusa slicer is not.

                          Simplify:

                          G90
M83
M106 S0
M140 S60
M190 S60
M104 S210 T0
M109 S210 T0
G28 ; home all axes
G29 ; mesh bed level
G1 X5 Y10 Z0.2 F3000 ; get ready to prime
G1 X160 E15 F600 ; prime nozzle
G1 X180 F5000 ; quick wipe
; process PLA Ender 5
; layer 1, Z = 0.150
T0
G1 E-1.0000 F2400
; feature skirt
; tool H0.150 W0.720
G1 Z0.150 F1002

                          Prusa Slicer:

                          M107
M190 S60 ; set bed temperature and wait for it to be reached
M104 S210 ; set temperature
G28 ; home all axes
G1 Z5 F5000 ; lift nozzle
M109 S210 ; set temperature and wait for it to be reached
G21 ; set units to millimeters
G90 ; use absolute coordinates
M82 ; use absolute distances for extrusion
G92 E0
; Filament gcode
G1 Z0.350 F10800.000

                          Z-Bot CoreXY Build | Thingiverse Profile

                          1 Reply Last reply Reply Quote 1
                          • Vetiundefined
                            Veti
                            last edited by Veti

                            prusa slicer

                            ; Filament gcode
                            G1 Z0.350 F10800.000

                            s3d
                            ; feature skirt
                            ; tool H0.150 W0.720
                            G1 Z0.150 F1002

                            your prusa settings
                            ; first_layer_height = 0.35

                            1 Reply Last reply Reply Quote 0
                            • First post
                              Last post
                            Unless otherwise noted, all forum content is licensed under CC-BY-SA