G30 S-1 is giving me heart stitches [SOLVED]

o_lampe

@fcwilt said in G30 S-1 is giving me heart stitches:

You also need to have M574 Z0 and a valid Z probe configuration

Thanks @fcwilt
I read that line last night and I couldn't find sleep, because it makes totally sense.
It's like re-purposing a fan connector for something else:

1. you have to undefine the fan
1. now you can define it as LED-light colour changer or whatever

@Phaedrux
I moved the drive mapping right behind the M667 CoreXY definition.

Now, downing the coffee and back to the printer

The new config.g. I've also changed the extruder settings, since the E3d Titan is the only new part of the printer. It's run by a 1.8° 1708 pancake stepper, an improvement against the 0.9° original motor i guess.
config.g

o_lampe

One problem less, two new problems?

I tested the new config and behaviour was unchanged. G30 refuses to run before Z axis is homed. When it runs, it goes all over the place instead of probing where it should.

G30 X20 Y20 S2 ; is a valid code,right?

Then I checked my M667 setting again. Here in RepRap-Wiki and then in the Duet dozuki pages and look, what it says:

This command is deprecated in RRF 2.03 and later. Use M669 instead.

So I used M669 K1 and started homeAll.

; homeall file for use with dc42 Duet firmware on CoreXY printers
; This file assumes the endstop switches are at the low end of each axis.
; Reverse the X and Y movement for high-end switches.
; Adjust the bed upper and lower limits in config.g (M208 commands) to get the correct homing positions

G91                       ; relative mode
G1 F2400 		   		; course home X or Y //S1 X-340 Y-240 
G1 S1 X-340               ; course home X
G1 S1 Y-240               ; course home Y
G1 X14 Y14 F600             ; move away from the endstops
G1 S1 X-20                ; fine home X
G1 S1 Y-20                ; fine home Y
G1 X20 Y20 F4000
G1 F600
G1 S1 Z-300 F600
G1 Z5 F200
G30 X20 Y20 S-2

; If you are using a microswitch for Z homing, insert similar code for the Z axis here,
; but use lower feed rates suitable for your Z axis.

G90                       ; back to absolute mode

The tool still dances around the bed, but luckily didn't crash anywhere. The endposition of it can be seen here:

WHY does it do that?
The good news is, when I move to X0 Y0 Z5, the position is almost correct.

Now I can spend my time with mesh bed leveling and see what happens next.

//edit Should I go to absolute positioning (G90) before G30 in homeAll? Hold your breath, BRB...

Veti

your homeall also uses old syntax.

the S1 is depricated.

also i dont understand why you are making your life so difficult, instead of using the correct generated homing files from the configurator.

Using S-2 here is incorrect

o_lampe

@Veti said in G30 S-1 is giving me heart stitches:

your homeall also uses old syntax.

the S1 is depricated.

No, it's not, the dozuki wiki says, they are the same.

G1 Xnnn Ynnn Znnn S0	Ignore endstops while moving.
G1 Xnnn Ynnn Znnn S1	Sense endstops while moving. On Delta (only), axis letters refer to individual towers.
G1 Xnnn Ynnn Znnn S2	Ignore endstops while moving. Also ignore if axis has not been homed. On Delta and CoreXY, axis letters refer to individual towers.
G1 Xnnn Ynnn Znnn S3	Sense endstops while measuring axis length, and set the appropriate M208 limit to the measured position at which the endstop switch triggers.

RRF_2.02 and later, BEFORE M452 Laser Mode.
S parameter behaves as shown above.

Veti

@o_lampe

since S has a double meaning, the use of H is encouraged.

o_lampe

@Veti said in G30 S-1 is giving me heart stitches:

Using S-2 here is incorrect

Maybe, but I also tried the other options, without any difference

o_lampe

@Veti said in G30 S-1 is giving me heart stitches:

@o_lampe

since S has a double meaning, the use of H is encouraged.

Just for your peace of mind, I'll try (again)

Why I don't use the config tool is simple: In MY config, I know every line. Where it is and what it does (or should do)
A generated file is different.

Veti

@o_lampe said in G30 S-1 is giving me heart stitches:

In MY config, I know every line. Where it is and what it does (or should do)
A generated file is different.

then at least look at the generated files so that you know how its supposed to be done

fcwilt

@o_lampe said in G30 S-1 is giving me heart stitches:

In MY config, I know every line. Where it is and what it does (or should do)

You don't seem to be paying attention.

In your new config.g file you have...

M574 X1 Y1 Z0 S1 - that is NOT correct - remove the Z0

M574 Z1 S2 - that is NOT correct - change it to M574 Z0

Now as to your homing file.

Do you have actual end stop switches for X and Y OR are you forcing them active?

IF you ARE forcing them active your homing file is not going to work.

G1 S1 X-340 - will not move but will mark X as homed at whatever position it happens to be at
G1 S1 Y-240 - will not move but will mark Y as homed at whatever position it happens to be at
G1 X14 Y14 - will move X and Y by 14mm in the direction of the high end of the each axis
G1 S1 X-20 - does nothing - will not move
G1 S1 Y-20 - does nothing - will not move
G1 F600 - serves no purpose - remove it
G1 S1 Z-300 F600 - is incorrect - remove it - you are going to use the z probe for homing Z
G1 Z5 F200 - should generate an error as Z is not homed - remove it
G30 X20 Y20 S-2 - that is not valid syntax - to home with Z probe just use G30 by itself

But without actual X and Y end stop sensors you might as well just do the following.

G92 X0 - mark X as homed and at position X = 0
G92 Y0 - mark Y as homed and at position Y = 0
G30 - home Z at the current X and Y position - whatever that happens to be

This would work IF the actual starting position of X was 0 and Y was 0.

If will be so much simpler if you either install X and Y end stop switches OR use sensor-less homing for X and Y

Frederick

o_lampe

@fcwilt said in G30 S-1 is giving me heart stitches:

M574 Z1 S2 - that is NOT correct - change it to M574 Z0

Although I must admit that you are right with most of your comment, this line is correct for using the z-probe as endstop.
Quote from M574 wiki

Snnn Endstop type: ... 2 = Z probe

Why did I keep all the useless lines in homeAll? Simply don't want to write it again, when I have real endstops.

o_lampe

@fcwilt said in G30 S-1 is giving me heart stitches:

G1 S1 Z-300 F600 - is incorrect - remove it - you are going to use the z probe for homing Z
G1 Z5 F200 - should generate an error as Z is not homed - remove it

As I said earlier, I have to home the Z-axis before running G30. And that's exactly what it does. And it does lift 5mm afterwards, because the axis is now homed according to DWC.
The only it doesn't do, is giving me a Z=0 datum. also G92 Zxxx doesn't.

That's why I had to deal with G30.

Veti

there G30 does not need the z axis to be homed

fcwilt

@o_lampe said in G30 S-1 is giving me heart stitches:

Read it all:

Snnn 1 = switch-type (eg microswitch) endstop input, 2 = Z probe (when used to home an axis other than Z), 3 = single motor load detection, 4 = multiple motor load detection (see Notes).

M574 Z0 is correct.

Frederick

o_lampe

@fcwilt
where's that from, please?

fcwilt

@o_lampe said in G30 S-1 is giving me heart stitches:

@fcwilt
where's that from, please?

Where is what from?

Frederick

fcwilt

@o_lampe said in G30 S-1 is giving me heart stitches:

As I said earlier, I have to home the Z-axis before running G30. And that's exactly what it does.

Because you didn't have M574 Z0 saying to home with the z probe.

Frederick

o_lampe

@fcwilt said in G30 S-1 is giving me heart stitches:

2 = Z probe (when used to home an axis other than Z)

Sorry, I should've quoted it...
Here is the link, I refered to

fcwilt

@o_lampe said in G30 S-1 is giving me heart stitches:

@fcwilt said in G30 S-1 is giving me heart stitches:

2 = Z probe (when used to home an axis other than Z)

Sorry, I should've quoted it...
Here is the link, I refered to

I thought you had upgrade to v3 firmware. Have you not done so yet?

Frederick

o_lampe

@fcwilt
here's another quote, I took from wiki

Example

    M574 X1 Y2 Z0 S1 ; X endstop at low end, Y endstop at high end, no Z endstop, all active high

What's wrong with that compared to your M574 Z0?

fcwilt

@o_lampe said in G30 S-1 is giving me heart stitches:

@fcwilt
here's another quote, I took from wiki
Example

    M574 X1 Y2 Z0 S1 ; X endstop at low end, Y endstop at high end, no Z endstop, all active high
What's wrong with that compared to your M574 Z0?

It looks like you haven't upgraded to v3 firmware - I thought you were going to do that.

Frederick