Error: bad Command XXX W/RRF 3.2 and leveling issue

3DPrintingWorld

@Phaedrux Ha, you got to give me more credit then that. Yes, I'm modifying the config file in my systems folder. I know because I also swapped the left and right stepper motors and if I don't update the directions in the config one of the motors will be rotating in the wrong direction. Speaking that, like it says here. When I swap the X motors it should be leveling the opposite but I swapped the motors but its still identically off level.

Phaedrux

I had to ask. It happens sometimes.

3DPrintingWorld

Is its possible that the firmware is corrupt? I tried reverting to 3.1 but it did not fix any of the issues. Is there a way to remove it and do a fresh install?

3DPrintingWorld

I manually adjusted the bed so it was out of level and I swapped a front motor with the back motor. It still levels at the same off level point? No matter what I do changes nothing, It makes no sense.

Phaedrux

Can you report your current file set?
Also the results of M98 P"config.g"?

3DPrintingWorld

@Phaedrux said in Error: bad Command XXX W/RRF 3.2 and leveling issue:

results of M98 P"config.g"?

m98 config g.png

3DPrintingWorld

@Phaedrux said in Error: bad Command XXX W/RRF 3.2 and leveling issue:

Can you report your current file set?

I'm not sure I understand, can you explain?

Phaedrux

Sorry, meant to type repost. As in, upload your current files so we can see what's up.

3DPrintingWorld

@Phaedrux said in Error: bad Command XXX W/RRF 3.2 and leveling issue:

current files

Not sure what you mean "current files", I've already been asked to post config.g and bed.g. I would think the only other one that would pertain would be homeall.g.

; homeall.g

; X,U,Y Homing
T0 P0
G91                         ; relative positioning
G1 H2 Z5 F2000              ; lift Z relative to current position
G1 H1 X-475 U475 F7500      ;Rough home X and U axis
G1 H1 X-475                  ; home X axis
G1 H1 U475                 ; home U axis
G1 H2 X5 U-5 F7500           ; go back a few mm
G1 H1 Y500 F6000            ; move quickly to Y axis endstop and stop there (first pass)
G1 Y-5  F6000               ; go back a few mm
M584 Y1                     ; Y-axis right side 
M574 Y2 S1 P"ystop"         ; Y-axis right side endstop Active
G1 H1 Y15 F360              ; move slowly to Y axis endstop once more (second pass)
M584 Y2                     ; Y-axis Left side
M574 Y2 S1 P"zstop"        ; Y-axis left side endstop Active
G1 H1 Y15 F360              ; move slowly to Y axis endstop once more (second pass)
M584 Y1:2                   ; Combine Y-Axis
M574 Y2 S1 P"ystop+zstop"  ; Y Double max active high endstop switch
G1 Y-5  F6000               ; go back a few mm
G1 H1 X-25 F360              ; move slowly to X axis(second pass)
G1 H1 U25                  ; move slowly to U axis(second pass)
G1 H2 X2 U-2 F7500              ; go back a few mm

; Z Homing
T0 P0
G90 G1 X219 Y150 F6000      ; Move to the center of the bed
M558 F500                    ; Fast probing speed
G30                          ; First probe
M558 F50                     ; Slow probing speed
G30                          ; Second probe
G32                          ; Level the bed
G90 G1 X219 Y150 F7500      ; Move to the center of the bed
G30                          ; Bed Deviation probe
G90 G1 X-16                  ; Park x-axis

Phaedrux

@3DPrintingWorld said in Error: bad Command XXX W/RRF 3.2 and leveling issue:

Not sure what you mean "current files",

In case you've made any changes since posting.

3DPrintingWorld

@Phaedrux I've made changes but I reverted back to the original after testing.

Phaedrux

The only thing I can think of to cause the leveling to be oposite of expected is if the order of the motors doesn't match the order of the points defined.

You must use the M671 command to define the X and Y coordinates of the leadscrews. The M671 command must come after the M584 command and must specify the same number of X and Y coordinates as the number of motors assigned to the Z axis in the M584 command; and these coordinates must be in the same order as the driver numbers of the associated motors in the M584 command. The M671 command must also come after any M667 or M669 command.

https://duet3d.dozuki.com/Wiki/Bed_levelling_using_multiple_independent_Z_motors

I can't see your printer so I don't know which motor is at which point, but that's the first thing I would double check.

3DPrintingWorld

@Phaedrux I don't think the leveling is opposite as expected. It adjusts to the same plane every time, its just off level with the left back corner low and front right corner height. I swapped the motor drivers because it should make the leveling different, but the leveling stayed exactly the same. I swapped right and left motors and left and back motors. Therefore I dont see why it matters if my motors are assigned correctly because no matter their assignment the bed is leveled to the same position.

Circling back to if the motors are assigned and wired correctly, there are two others builders that used my config.g and wiring as a basis but are not having this issue. Plus the bed was leveling properly for six months and I have not changed the wiring or the motor assignment.

You can find the wiring diagram here:
https://github.com/3dprintingworld/MULDEX/blob/master/Images/MULDEX WIRING DIAGRAM.png

Phaedrux

Is there a skew in the frame? Tilt on the print head?

3DPrintingWorld

@Phaedrux
I don't see how the frame could be out of square, the extrusions are machined square and butt connected together so its not possible for it to no be square.

Also, the axis would have to be skewed so far to result in a .4mm vertical variance in level of the bed.

3DPrintingWorld

Here is what I verified mechanically:

I tried a backup BL touch
Tried running the cable for the BL touch separately incase there was interference with the heater cable.
I rebuilt the extruder carriage twice to make sure there was nothing wrong with the assembly.
Checked the set screws on pulleys.
Checked belt tension.
Loosed up the cable loom and supported it as the printer homed to verify the loom was not pulling on the carriage resulting bad readings from the BL touch.

3DPrintingWorld

How can I run this trigger test macro that probes the three places used to home and it says the deviation is less than .01mm but in reality its .4mm? I can run the macro a bunch of times and it will return a .002 to .009mm deviation. Its repeating very accurately, but it seems as the printer thinks its level but its not.

T0
G28
G90
M558 F60				; Slow probing speed
G30 P0 X200 Y285 Z-99999   ; Probe Middle
G30 P1 X15 Y15 Z-99999     ; Probe Left
G30 P2 X324 Y15 Z-99999 S-1 ; Probe Righ

engikeneer

@3DPrintingWorld you my have checked this, but do you have your heightmap loaded when running bed.g? If mesh compensation is active, it will cause something similar where the bed looks tilted, but it adjusts it up and down so the probed height doesn't show thr tilt.
I always start all my homing and bed.g files with a G29 S-2 to make sure I don't have a heightmap loaded (/mesh compensation active)

dc42

@3DPrintingWorld said in Error: bad Command XXX W/RRF 3.2 and leveling issue:

How can I run this trigger test macro that probes the three places used to home and it says the deviation is less than .01mm but in reality its .4mm? I can run the macro a bunch of times and it will return a .002 to .009mm deviation. Its repeating very accurately, but it seems as the printer thinks its level but its not.

My guess is that the print heat is tilting a little depending on the direction in which it last moved. This will cause the relative heights of the nozzle and the BLTouch to change. Please post photos of the print carriage assembly.

martin7404

HI,
I have built the same design, just measured the tilt in the X linear cartridge. It is 0.07mm in Z direction on the nozzle and is caused by the tolerance linear rail to block LDO MGN9 . So there is a few hundreds luft between the block and rail and due to the center of the nozzle( and BL touch) being about 20-25 mm cantilever, the resulting is 0.07 measured with a dial indicator on the tip of the nozzle. SO no way this can give 0.4 mm difference. The U axis caridge has a similar wobble.
I think We may need a better linear rail and block for the X axis. What I see is that I do G32 it makes the initial correction, then G32 with -1 and it reports deviation of about 0.1to 0.15 mm , then I do G32 S3 again and then G32 -1 and it reports 0.002 to 0.01 deviation, from there every G32 reports under 0.01