Diag flashing
-
@Phaedrux said in Diag flashing:
M98 P"config.g"
3/10/2021, 7:27:21 PM M98 P"config.g"
HTTP is enabled on port 80
FTP is disabled
TELNET is disabled -
This post is deleted! -
@anthony1m That looks good. No errors anyway.
-
@anthony1m said in Diag flashing:
WiFi firmware version 1.23
It looks like the wifi server didn't get updated.
Try uploading the full release zip file again to the system tab in DWC. Just to make sure everything is correct.
https://github.com/Duet3D/RepRapFirmware/releases/download/3.2.2/Duet2and3Firmware-3.2.2.zip
-
Will need to see your homing files to say why it's moving the way it's moving during homing. Post homeall.g homex.g homey.g homez.g and bed.g if you've set that up yet.
-
@Phaedrux I'm close3/10/2021, 8:10:02 PM m122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.2.2 running on Duet WiFi 1.02 or later
Board ID: 08DLM-996RU-N85S4-7JTD6-3SJ6R-KA9BR
Used output buffers: 3 of 24 (10 max)
=== RTOS ===
Static ram: 23460
Dynamic ram: 73268 of which 40 recycled
Never used RAM 15312, free system stack 189 words
Tasks: NETWORK(blocked,186) HEAT(blocked,308) MAIN(running,457) IDLE(ready,20)
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 00:01:47 ago, cause: software
Last software reset at 2021-03-10 20:08, reason: User, GCodes spinning, available RAM 15068, slot 2
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Aux0 errors 0,0,0
MCU temperature: min 31.3, current 32.0, max 32.4
Supply voltage: min 21.9, current 22.1, max 22.3, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: position 0, standstill, SG min/max not available
Driver 1: position 0, standstill, SG min/max not available
Driver 2: position 0, standstill, SG min/max not available
Driver 3: position 0, standstill, SG min/max not available
Driver 4: position 0, standstill, SG min/max not available
Driver 5: position 0
Driver 6: position 0
Driver 7: position 0
Driver 8: position 0
Driver 9: position 0
Driver 10: position 0
Driver 11: position 0
Date/time: 2021-03-10 20:10:01
Cache data hit count 129951247
Slowest loop: 4.40ms; fastest: 0.21ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 3.2ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 15.91ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8- WiFi -
Network state is active
WiFi module is connected to access point
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.23
WiFi MAC address 48:3f:da:88:d4:72
WiFi Vcc 3.38, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 22120
WiFi IP address 192.168.0.197
WiFi signal strength -36dBm, mode none, reconnections 0, sleep mode modem
Clock register ffffffff
Socket states: 0 0 0 0 0 0 0 0
- WiFi -
-
@Phaedrux I think you can check this as solved . I will work on it and if I run into any issued Ill read the information and ask for help if I need it. You guys are awesome thank you.
-
@Phaedrux well this happened again except now the diag is on solid and windows disconnected right away. it was fine middle of a print it dropped connection and does nothing.
-
@Phaedrux any ideas Its on a new meanwell ps also , why this board keeps having diag issues it brand new.
-
https://duet3d.dozuki.com/Wiki/What_to_do_if_your_Duet_won't_respond
Can you run through this guide and see how far you can get?
-
@Phaedrux yes thank you I am working on that now.
-
"Error reading device descriptor" This is as far as I get, I can't get past that. That's the one I was working last night before I came back here. my mac or rpi 4 wont see it either usb not recognized with or with a sd card different ports and cables and restart of the machine.
-
@Phaedrux Had it dialed in was producing some great prints, Then just in the middle stopped and could not connect again.
-
When and where did you purchase the Duet?
What LEDs light up when connected to VIN or USB?
-
This post is deleted! -
diag, usb, 3.3v ,5v. 3 red one green all solid computer just said the devise malfunctioned and windows does not recognize it
-
febuary 17 2021 printed solid
-
Please contact your vendor and initiate a warranty exchange. Please include a link to this thread as authorization.
