duet 2 wifi stop in printing

flyingpig507

Hi, my DWC reconnect in printing then last progress was lost, the “status” display: No Job running.

It is DIY Cartesian i3 style. Just stuck in there:

Here's some information:

Board: Duet 2 WiFi (2WiFi)
Firmware: RepRapFirmware for Duet 2 WiFi/Ethernet 3.2.2 (2021-02-11)
Duet WiFi Server Version: 1.25

M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.2.2 running on Duet WiFi 1.02 or later
Board ID: 0JD0M-9K662-MGPSS-6J9DL-3S86P-18V6Z
Used output buffers: 3 of 24 (10 max)
=== RTOS ===
Static ram: 23460
Dynamic ram: 73228 of which 40 recycled
Never used RAM 15352, free system stack 193 words
Tasks: NETWORK(ready,183) HEAT(blocked,308) MAIN(running,449) IDLE(ready,20)
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 00:00:15 ago, cause: software
Last software reset at 2021-04-26 21:28, reason: StuckInSpinLoop, GCodes spinning, available RAM 15108, slot 2
Software reset code 0x4083 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f80f BFAR 0xe000ed38 SP 0x200040ac Task MAIN Freestk 772 ok
Stack: 0041f9c3 00459a3c 610f0200 3f800000 3d7df000 3edb6db7 b61cf800 49742404 3c3fdc9b 440739fd 40e190bc 0000bb9b 00000000 3e4fa932 41ddae4f 4e64e1c0 38533333 3f800000 3f800000 20000011 00000000 00000001 00000000 00000000 20002544 00000001 0041f9c3
Error status: 0x00
Aux0 errors 0,0,0
MCU temperature: min 32.6, current 33.3, max 33.5
Supply voltage: min 24.8, current 25.0, max 25.2, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: position 0, standstill, SG min/max not available
Driver 1: position 0, standstill, SG min/max not available
Driver 2: position 0, standstill, SG min/max not available
Driver 3: position 0, standstill, SG min/max not available
Driver 4: position 0, standstill, SG min/max not available
Driver 5: position 0
Driver 6: position 0
Driver 7: position 0
Driver 8: position 0
Driver 9: position 0
Driver 10: position 0
Driver 11: position 0
Date/time: 2021-04-26 21:29:14
Cache data hit count 17227880
Slowest loop: 6.87ms; fastest: 0.21ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 1.0ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 177.94ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8

WiFi -
Network state is active
WiFi module is connected to access point
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.25
WiFi MAC address 50:02:91aa:53
WiFi Vcc 3.49, reset reason Power up
WiFi flash size 4194304, free heap 26568
WiFi IP address 192.168.0.198
WiFi signal strength -60dBm, mode 802.11n, reconnections 0, sleep mode modem
Clock register 00002002
Socket states: 0 0 0 0 0 0 0 0

=================================================================
config.g

G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"daZhu_i3" ; set printer name

; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet

; Drives
M569 P0 S0 ; physical drive 0 goes forwards
M569 P1 S0 ; physical drive 1 goes forwards
M569 P2 S1 ; physical drive 2 goes forwards
M569 P3 S1 ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X100.00 Y100.00 Z800.00 E381.92 ; set steps per mm
M566 X900.00 Y900.00 Z60.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
M203 X7200.00 Y7200.00 Z3600.00 E1800.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00 E250.00 ; set accelerations (mm/s^2)
M906 X600 Y600 Z600 E600 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X172 Y200 Z150 S0 ; set axis maxima

; Endstops
M574 X1 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop
M574 Y1 S1 P"ystop" ; configure active-high endstop for low end on Y via pin ystop
M574 Z1 S1 P"zstop" ; configure active-high endstop for low end on Z via pin zstop

; Z-Probe
; M558 P0 H5 F120 T7200 ; disable Z probe but set dive height, probe speed and travel speed
; M557 X15:190 Y15:195 S20 ; define mesh grid
; Z-Probe
M950 S0 C"exp.heater3" ; create servo pin 0 for BLTouch
M558 P9 C"^zprobe.in" H5 F120 T3000 ; set Z probe type to bltouch and the dive height + speeds
G31 P25 X-42.8 Y-5.5 Z3.011 ; set Z probe trigger value, offset and trigger height
M557 X10:128 Y10:190 S118:180 ; define mesh grid

; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M307 H0 R0.213 C685.2 D3.92 S1.00 V24.0 ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S100 ; set temperature limit for heater 0 to 100C
M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 R3.569 C137.0 D6.19 S1.00 V24.0 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S280 ; set temperature limit for heater 1 to 280C

; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss

Please help me, Thanks.

felek

@flyingpig507
Hi!
Did you have similar issue before?
According to stack trace it looks like some sd card issue.
Let's replace this sd card.

alankilian

@felek I'm interested in learning more about how you come to this conclusion.

I see:

reason: StuckInSpinLoop, GCodes spinning

And in RepRapFirmware-3.3beta3/src/Platform/RepRap.cpp" line 734 there is:

ticksInSpinState = 0;
spinningModule = moduleGcodes;
gCodes->Spin();

Which points me to whatever the method gCodes->Spin() is doing.

felek

@alankilian
In M122 you have more precise information:

Stack: 0041f9c3 00459a3c 610f0200 3f800000 3d7df000 3edb6db7 b61cf800 49742404 3c3fdc9b 440739fd 40e190bc 0000bb9b 00000000 3e4fa932 41ddae4f 4e64e1c0 38533333 3f800000 3f800000 20000011 00000000 00000001 00000000 00000000 20002544 00000001 0041f9c3

Next step is download file with map file. You need to do it for your board and firmware version.
In your case it is this zip file https://github.com/Duet3D/RepRapFirmware/releases/download/3.2.2/Symbols-RepRapFirmware-Duet2.zip

There is .map file which include functions addresses in memory.
Then you need to compare your stack address and map file function address.

flyingpig507

@felek
This is my TF

This duet board I used almost a year ago. It's been good before (Firmware 1.x). Similar problems was happen until I update Firmware.
I not sure always used this TF, maybe changed it...
I will chang other TF try again.
Thanks you.

flyingpig507

I changed TF, it is fine. thank felek (｡･∀･)ﾉﾞ