npn 5v fly rrf e3

npm1

@gloomyandy Without M574
M98 P"config.g"
HTTP is enabled on port 80
FTP is disabled
TELNET is disabled
Endstops - X: not stopped, Y: at min stop, Z: no endstop, Z probe: not stopped
Z probe 0: current reading 0, threshold 500, trigger height 2.500, offsets X0.0 Y0.0

gloomyandy

@npm1 Are those results with or without the probe being in a triggered state?

npm1

@gloomyandy the first response is with m574 and the second response is without m574

gloomyandy

@npm1 Yes but I asked you to run M119 and G31 twice for each test once without having the probe in a triggered state and then again with the probe in a triggered state (by placing something metal near it so the LED comes on). Have you run the test with the Z driver removed?

npm1

@gloomyandy
without m574 and with metal touching the probe

g31

Z probe 0: current reading 0, threshold 500, trigger height 2.500, offsets X0.0 Y0.0
2/25/2022, 8:46:38 PM g31
2/25/2022, 8:46:16 PM M119
Endstops - X: not stopped, Y: at min stop, Z: no endstop, Z probe: not stopped
2/25/2022, 8:45:56 PM M98 P"config.g"
HTTP is enabled on port 80
FTP is disabled
TELNET is disabled

npm1

@gloomyandy with 574 and metal touching probe
g31
Z probe 0: current reading 0, threshold 500, trigger height 2.500, offsets X0.0 Y0.0
2/25/2022, 8:50:23 PM g31
2/25/2022, 8:50:05 PM m119
Endstops - X: not stopped, Y: at min stop, Z: not stopped, Z probe: not stopped

gloomyandy

@npm1 and the results with the Z driver removed from the socket?

npm1

@gloomyandy

removed z driver with m574
g31
Z probe 0: current reading 0, threshold 500, trigger height 2.500, offsets X0.0 Y0.0
2/25/2022, 8:59:47 PM M119
Endstops - X: not stopped, Y: at min stop, Z: not stopped, Z probe: not stopped
2/25/2022, 8:59:44 PM M119
2/25/2022, 8:59:33 PM M98 P"config.g"
HTTP is enabled on port 80
FTP is disabled
TELNET is disabled

npm1

@gloomyandy removed z driver with m574 metal touching

g31
Z probe 0: current reading 0, threshold 500, trigger height 2.500, offsets X0.0 Y0.0
2/25/2022, 9:01:46 PM g31
2/25/2022, 9:01:24 PM M119
Endstops - X: not stopped, Y: at min stop, Z: not stopped, Z probe: not stopped

npm1

@gloomyandy removed z driver without m574

g31

Z probe 0: current reading 0, threshold 500, trigger height 2.500, offsets X0.0 Y0.0
2/25/2022, 9:04:04 PM g31
2/25/2022, 9:03:53 PM M119
Endstops - X: not stopped, Y: at min stop, Z: no endstop, Z probe: not stopped

npm1

@gloomyandy removed z driver without m574 metal touching

G31

Z probe 0: current reading 0, threshold 500, trigger height 2.500, offsets X0.0 Y0.0
2/25/2022, 9:05:35 PM m119
Endstops - X: not stopped, Y: at min stop, Z: no endstop, Z probe: not stopped

npm1

hope that helps

gloomyandy

@npm1 Are you still using this line for your probe definition:

M558 P5 C"!^zstop" H5 F120 T6000

If so with the Z driver still removed enter

M558 P5 C"zstop" H5 F120 T6000

in the console (or change the line in your config.g and reboot)
and rerun both sets of tests.

npm1

@gloomyandy still no changes, the only thing that change is the z probe value being 1000 instead of zero

npm1

@gloomyandy have I blown something on the board

npm1

shall i update the firmware

npm1

Electronics
Diagnostics
Board: fly_E3 (STMWiFi)
Firmware: RepRapFirmware for STM32F4 based Boards 3.3RC2+1_1 (2021-05-13)
Duet WiFi Server Version: 1.26-01S-D

Note: You can install updates on the System page.

npm1

will marlin be easier

gloomyandy

@npm1 Can you turn off your board, disconnect the probe and plug in one of the other endstop switches (x or y) into the zstop socket. Then run the two tests again once without pressing the endstop switch, then again with the endstop switch pressed. Run this test with the Z driver still removed.

npm1

@gloomyandy endstop works with zero issues with everything triggered correctly

M119

Endstops - X: at min stop, Y: at min stop, Z: at min stop, Z probe: at min stop
2/25/2022, 9:38:20 PM g31
Z probe 0: current reading 0, threshold 500, trigger height 2.500, offsets X0.0 Y0.0
2/25/2022, 9:38:10 PM m119
Endstops - X: at min stop, Y: at min stop, Z: not stopped, Z probe: not stopped