Hello,
I'm facing a annoying problem, and I don't know how to solve.
I have a IR Z-probe sensor, and I calibrate the the triggered height on every point. Then I run G32, but sometimes the nozzle is a bit high from bed and I decrease the z baby step, but the nozzle doesn't go down. Why does this happen?

@Phaedrux I just bought a band new sd card, copy the DWC files downloaded from github and the configs file just copied from the old sd card. And the problems continues. Any other guess how to solve it?

And thanks for your time to supporting me

@jay_s_uk So do I.

@chrishamm I tried on my laptop and Firefox and Edge. Same problem on all browsers and devices.

Maybe it is causing by the wrong speed, but I have no idea how to fix it

@Stockerbot Thanks, I will buy one to test it.

Sure, my mistake..

Duet 2 Wifi
FW 3.2.2
Duet Wifi Server 1.25
DWC 3.2.2

M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.2.2 running on Duet WiFi 1.02 or later
Board ID: 0JD0M-9P6M2-NW4SJ-6J9FL-3S46N-9TU7M
Used output buffers: 3 of 24 (24 max)
=== RTOS ===
Static ram: 23460
Dynamic ram: 73048 of which 60 recycled
Never used RAM 15424, free system stack 101 words
Tasks: NETWORK(ready,155) HEAT(blocked,294) MAIN(running,166) IDLE(ready,20)
Owned mutexes: WiFi(NETWORK) HTTP(MAIN)
=== Platform ===
Last reset 73:00:00 ago, cause: power up
Last software reset at 2021-02-18 22:39, reason: User, GCodes spinning, available RAM 15512, slot 0
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x1c
Aux0 errors 182,182,182
MCU temperature: min 30.6, current 33.2, max 44.9
Supply voltage: min 23.6, current 23.8, max 24.6, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: position 103188, standstill, SG min/max 0/1023
Driver 1: position 103188, standstill, SG min/max 0/1023
Driver 2: position 103188, standstill, SG min/max 0/1023
Driver 3: position 0, standstill, SG min/max 0/1023
Driver 4: position 0, standstill, SG min/max not available
Driver 5: position 0
Driver 6: position 0
Driver 7: position 0
Driver 8: position 0
Driver 9: position 0
Driver 10: position 0
Driver 11: position 0
Date/time: 2021-02-22 08:51:15
Cache data hit count 4294967295
Slowest loop: 113.47ms; fastest: 0.11ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 9.0ms, write time 426.3ms, max retries 0
=== Move ===
DMs created 84, maxWait 159353166ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 193, completed moves 193, hiccups 206, stepErrors 0, LaErrors 0, Underruns [0, 0, 2], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = 2 -1 -1 -1
Heater 0 is on, I-accum = 0.5
Heater 1 is on, I-accum = 0.3
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is ready with "M122 " in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 428.77ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8
- WiFi -
Network state is active
WiFi module is connected to access point 
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.25
WiFi MAC address 48:3f:da:79:34:48
WiFi Vcc 3.35, reset reason Power up
WiFi flash size 4194304, free heap 24328
WiFi IP address 192.168.0.199
WiFi signal strength -66dBm, mode 802.11n, reconnections 0, sleep mode modem
Clock register 00002002
Socket states: 0 0 0 0 0 0 0 0

Hi,

When I upload a gcode file, the percentage of the uploading doesn't change, it is fixed at 100%.
I made a video to show the problem.

Does anyone have this problem?

clip0005.mp4

@arhi do you test it on your board?
I want to buy the same sensor you did.

I installed and it worked but not all commands.
/status - not working
/macros - not working