Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login
    1. Home
    2. briangilbert
    • Profile
    • Following 0
    • Followers 0
    • Topics 18
    • Posts 116
    • Best 0
    • Controversial 0
    • Groups 0

    briangilbert

    @briangilbert

    0
    Reputation
    6
    Profile views
    116
    Posts
    0
    Followers
    0
    Following
    Joined Last Online
    Website zesty.tech Location Australia

    briangilbert Unfollow Follow

    Latest posts made by briangilbert

    • RE: Paneldue beeping constantly

      Seems strange given the case has been on it since day one, but I'll take it out of the case and see if it resolves it.. will report back. thanks

      posted in General Discussion
      briangilbertundefined
      briangilbert
    • Paneldue beeping constantly

      Re: PanelDue beeping? Confused.

      My Paneldue has started beeping constantly, the weird thing is that it still registers touches, and the printer still works fine if I operate it from the web interface, I had to unplug the paneldue due to the annoyance of the noise.. and suggestions how I can fix the paneldue to stop it from beeping?

      posted in General Discussion
      briangilbertundefined
      briangilbert
    • Using 8 wire steppers?

      I assume this just means running 2 wires to each of the stepper pins on the duet, are there any concerns with doing this other than current?

      8-Wire Stepper Motors

      Some motors are also offered in 8-Wire configurations allowing for multiple wiring configurations depending on whether the motor's speed or torque is more important.*

      It is possible to connect an 8-wire stepper motor with the windings of each phase connected in parallel as shown in Figure 4. This configuration will enable better high speed operation while requiring more current to produce the rated torque. This connection type is sometimes known as parallel bipolar wiring.
      from : https://knowledge.ni.com/KnowledgeArticleDetails?id=kA00Z000000PAkPSAW

      posted in Duet Hardware and wiring
      briangilbertundefined
      briangilbert
    • RE: PT1000 cable length, connector, and wire type

      @dc42 thanks, I was hoping this would be the case.

      posted in Duet Hardware and wiring
      briangilbertundefined
      briangilbert
    • RE: Welcome to the New Forum

      @msquared thanks.. do you know if there is a mobile app that supports it?

      Beside Safari 😉

      posted in General Discussion
      briangilbertundefined
      briangilbert
    • RE: PT1000 cable length, connector, and wire type

      @MSquared I think thats more for PT100 sensors..

      posted in Duet Hardware and wiring
      briangilbertundefined
      briangilbert
    • RE: Welcome to the New Forum

      Is it possible to enable the mobile API's so that I can use the Discourse app to read and respond on my phone?

      posted in General Discussion
      briangilbertundefined
      briangilbert
    • PT1000 cable length, connector, and wire type

      @dc42 or anyone else with more experience than me..

      Would there be any obvious issues using a PT1000 with a short cable (~10cm) going to a plug/socket just above effector, and then wire back down to the Duet?

      Anything special need to be taken into account for the wire used for the run back to the Duet (AWG rating, resistance, etc)?

      posted in Duet Hardware and wiring
      briangilbertundefined
      briangilbert
    • RE: Laser filament monitor

      @T3P3Tony please count me in if there is still room for more testers

      posted in Filament Monitor
      briangilbertundefined
      briangilbert
    • RE: Can't connect to wifi after firmware update

      Just reporting back that after updating my network gear to Ubiquiti Unifi kit everything is working properly again.

      posted in General Discussion
      briangilbertundefined
      briangilbert