I'm pretty sure the IR thermometer is reading accurate within ~5c because it works on the other printer I have within that range.
If the IR is under reading so drastically then why wont the filament melt? Is there another reason that the filament melts in another printer at 250c and not this machine with the EPCOS thermistor?
Thank you for your help.
As the title suggests I need the config for the EPCOS B57540G1104 thermistor.
I'm using it for my single extruder hotend powered by the Duet 2 WiFi board.
When I use T100000 B4092 R4700, and even with a C value calculated from this calculator with -55c, 25c, and 280c based off of this data sheet, I still get readings that are 60c+ higher than actual temperature at target 250c. (my infrared thermometer only goes to 250c)
What am I doing wrong? Does someone already have this thermistor dialed in to within a few degrees Celsius?
PS - The reason I'm targeting 280c is because I need to print ePA-CF at 60-70mm/s. I topped out at 40mm/s at 250c. Someone told me they hit my target print speed at 280c.
The web interface is whatever comes inside Duet2and3Firmware-3.1.1.zip as that's the package I used to install the latest firmware that I could find.
M115:
FIRMWARE_NAME: RepRapFirmware for Duet 2 WiFi/Ethernet FIRMWARE_VERSION: 3.1.1 ELECTRONICS: Duet WiFi 1.02 or later FIRMWARE_DATE: 2020-05-19b2
config.g
; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.1.3 on Tue Jun 23 2020 15:03:13 GMT-0700 (Pacific Daylight Time)
; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"Ender 3 Modified Monster" ; set printer name
M918 P1 E4 F2000000 ; configure direct-connect display
; Network
M551 P"xxxxxx" ; set password
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet
; Drives
M569 P0 S1 ; physical drive 0 (X) goes forwards
M569 P1 S0 ; physical drive 1 (Y) goes backwards
M569 P2 S1 ; physical drive 2 (Z) goes forwards
M569 P3 S1 ; physical drive 3 (E0) goes forwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z400.00 E93.00 ; set steps per mm
M566 X1200.00 Y1200.00 Z24.00 E300.00 ; set maximum instantaneous speed changes (mm/min)
M203 X9000.00 Y9000.00 Z180.00 E6000.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z100.00 E5000.00 ; set accelerations (mm/s^2)
M906 X500 Y500 Z500 E700 I50 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout
; Axis Limits
M208 X0 Y-12 Z0 S1 ; set axis minima
M208 X235 Y220 Z250 S0 ; set axis maxima
; Endstops
M574 X1 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop
M574 Y1 S1 P"ystop" ; configure active-high endstop for low end on Y via pin ystop
M574 Z1 S1 P"zstop" ; configure active-high endstop for low end on Z via pin zstop
; Z-Probe
M558 P0 H5 F120 T6000 ; disable Z probe but set dive height, probe speed and travel speed
M557 X15:200 Y15:200 S20 ; define mesh grid
; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4092 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B1 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S550 ; set temperature limit for heater 0 to 550C
M308 S1 P"e0temp" Y"thermistor" T100000 B3950 R4700 ;C1.739356e-7 configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on
M950 F2 C"fan2" Q500 ; create fan 2 on pin fan2 and set its frequency
M106 P2 S1 H1:0 T45 ; set fan 2 value. Thermostatic control is turned on
; Tools
M563 P0 S"Extruder 1" D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
; Custom settings are not defined
M143 H1 S550
; Miscellaneous
M912 P0 S-11.5
M501 ; load saved parameters from non-volatile memory
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss
I've been trying to replicate the event all day by letting the iPad sleep at 2 min intervals. So far not getting a repeat. I even tried logging in on Windows 10 and letting them both fall asleep.
@Phaedrux said in Print Stopping As 100% Complete When iPad Sleeps:
Can you tell us what firmware version and DWC version you are using?
RepRap 3.1.1 firmware.
What is DWC? The web interface?
Will post the config.g file in some hours.
Yes, with no success in tracing a cause. As well as reading a thread from 2018 with same event description, and following the suggestion to use M122 to debug any apparent actual problem, there was no reset event or any red flag information that would explain the event in M122 data. Last reset was 4 hours prior noted as startup. I will run several tests on a small print tomorrow to see if I can reliably create a circumstance that repeats the false finish event, but so far all investigation points to random bug of some sort that isn't producing an error.
Very srtrange.
I just experienced a very strange phenomenon. I was printing a 30 layer file that was supposed to take ~25 minutes. I decided to hop in the shower and figured the print would be complete when I was done showering.
Well, when I woke up the iPad (from it's sleep state) that I was using to monitor the web interface, the interface reported that the print was complete. However, the print head had stopped at the location I assume it was in when the iPad went to sleep. There was no return to home. The extrusion continued briefly until the extruder chamber pressure equalized with the atmosphere, so there was a small button of material that the nozzle was seated in. The heaters shut off. The print stopped on layer 14. I counted the layers with a viewing loop.
What would ever cause the Duet 2 Wifi board to halt all operation and report the print was completed aside from reaching the end of the gcode file that's on the card?
This is the third or fourth time I have had this issue and I assumed it was related to bad gcode file export from the slicer, but in the file the code clearly continues past layer 14. So, maybe there is a bug where sleep causes an emergency stop and reports print complete?
Any insight would be great, and appreciated.