@gloomyandy
gcode:
https://fastupload.io/K2qmozelOP3eK4A/file

I'm having troubles with my duet 3 mini board resetting during a print. I cannot figure out why this is happening.

Running a 1LC on my toolhead.

I was running 3.4.5 trying 3.5b2 with same problem. Reset happens within the first 4 layers. Nothing is pressing the reset button. Board mount on a PLA frame.

Here is the M122 after it reset, followed by the config. Any ideas?

m122
=== Diagnostics ===
RepRapFirmware for Duet 3 Mini 5+ version 3.5beta2 (2023-02-08 17:42:04) running on Duet 3 Mini5plus WiFi (standalone mode)
Board ID: F9FUW-DR6KL-K65J0-409NW-JUW1Z-RAJPQ
Used output buffers: 13 of 40 (24 max)
=== RTOS ===
Static ram: 103012
Dynamic ram: 120476 of which 12 recycled
Never used RAM 18212, free system stack 198 words
Tasks: NETWORK(notifyWait,9.4%,237) HEAT(notifyWait,0.0%,359) Move(notifyWait,0.0%,359) CanReceiv(notifyWait,0.0%,798) CanSender(notifyWait,0.0%,335) CanClock(delaying,0.0%,349) TMC(notifyWait,0.7%,114) MAIN(running,87.4%,449) IDLE(ready,1.7%,30) AIN(delaying,0.8%,272), total 100.0%
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 00:00:16 ago, cause: reset button
Last software reset at 2023-02-26 16:07, reason: User, Gcodes spinning, available RAM 17956, slot 1
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00446000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Aux0 errors 0,0,0
MCU revision 3, ADC conversions started 16166, completed 16166, timed out 0, errs 0
Step timer max interval 1488
MCU temperature: min 25.3, current 26.2, max 26.6
Supply voltage: min 23.9, current 24.0, max 24.1, under voltage events: 0, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Events: 0 queued, 0 completed
Driver 0: standstill, SG min 2, read errors 0, write errors 1, ifcnt 29, reads 819, writes 13, timeouts 0, DMA errors 0, CC errors 0
Driver 1: standstill, SG min 2, read errors 0, write errors 1, ifcnt 29, reads 819, writes 13, timeouts 0, DMA errors 0, CC errors 0
Driver 2: standstill, SG min 2, read errors 0, write errors 1, ifcnt 29, reads 819, writes 13, timeouts 0, DMA errors 0, CC errors 0
Driver 3: standstill, SG min 0, read errors 0, write errors 1, ifcnt 21, reads 822, writes 10, timeouts 0, DMA errors 0, CC errors 0
Driver 4: standstill, SG min 2, read errors 0, write errors 1, ifcnt 29, reads 819, writes 13, timeouts 0, DMA errors 0, CC errors 0
Driver 5: not present
Driver 6: not present
Date/time: 2023-02-26 19:35:49
Cache data hit count 30962431
Slowest loop: 6.68ms; fastest: 0.15ms
=== Storage ===
Free file entries: 20
SD card 0 detected, interface speed: 22.5MBytes/sec
SD card longest read time 1.0ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, segments created 0, maxWait 0ms, bed compensation in use: none, comp offset 0.000
no step interrupt scheduled
=== DDARing 0 ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== DDARing 1 ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters 0 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0
Heater 1 is on, I-accum = 0.0
=== GCodes ===
Movement locks held by null, null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
File2 is idle in state(s) 0
Queue2 is idle in state(s) 0
Q0 segments left 0, axes/extruders owned 0x0000803
Code queue 0 is empty
Q1 segments left 0, axes/extruders owned 0x0000000
Code queue 1 is empty
=== CAN ===
Messages queued 147, received 354, lost 0, boc 0
Longest wait 3ms for reply type 6026, peak Tx sync delay 160, free buffers 18 (min 17), ts 81/80/0
Tx timeouts 0,0,0,0,0,0
=== Network ===
Slowest loop: 13.46ms; fastest: 0.00ms
Responder states: MQTT(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0)
HTTP sessions: 1 of 8
= WiFi =
Network state is active
WiFi module is connected to access point 
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 2.1beta3
WiFi MAC address c4:5b:be:46:6a:64
WiFi Vcc 3.38, reset reason Power up
WiFi flash size 2097152, free heap 42492
WiFi IP address 10.0.50.249
WiFi signal strength -72dBm, mode 802.11n, reconnections 0, sleep mode modem
Clock register 00002001
Socket states: 0 0 0 0 0 0 0 0

; Configuration file for Duet 3 Mini 5+ (firmware version 3.3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.3.15 on Mon Dec 19 2022 16:33:45 GMT-0600 (Central Standard Time)

; General preferences
M575 P1 S1 B57600                                ; enable support for PanelDue
G90                                              ; send absolute coordinates...
M83                                              ; ...but relative extruder moves
M550 P"MyDuet"                                   ; set printer name

; Wait a moment for the CAN expansion boards to start
G4 S4

; Network
M552 S1                                          ; enable network
M586 P0 S1                                       ; enable HTTP
M586 P1 S0                                       ; disable FTP
M586 P2 S0                                       ; disable Telnet

; Drives
M569 P0.0 S1 D3                                  ; physical drive 0.0 goes forwards
M569 P0.1 S1 D3                                  ; physical drive 0.1 goes forwards
M569 P0.2 S0 D3                                  ; physical drive 0.2 goes backwards
M569 P0.4 S0 D3                                  ; physical drive 0.4 goes backwards
M569 P121.0 S1                                   ; physical drive 121.0 goes forwards
M584 X0.0 Y0.1 Z0.2:0.4 E121.0                   ; set drive mapping
M350 X16 Y16 Z16 E16 I1                          ; configure microstepping with interpolation
M92 X160.00 Y160.00 Z800.00 E397                 ; set steps per mm
M566 X600.00 Y600.00 Z60.00 E120.00              ; set maximum instantaneous speed changes (mm/min)
;M566 X900.00 Y900.00 Z60.00 E120.00              ; set maximum instantaneous speed changes (mm/min)
M203 X9000.00 Y9000.00 Z180.00 E1200.00          ; set maximum speeds (mm/min)
M201 X3500.00 Y3500.00 Z20.00 E250.00            ; set accelerations (mm/s^2)
M906 X1200 Y1200 Z1200 E1000 I50                 ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                          ; Set idle timeout

; Axis Limits
M208 X-10 Y0 Z0 S1                               ; set axis minima
M208 X300 Y300 Z350 S0                           ; set axis maxima

; Endstops
M574 X1 S1 P"!io5.in"                            ; configure switch-type (e.g. microswitch) endstop for low end on X via pin !io5.in
M574 Y1 S1 P"!io6.in"                            ; configure switch-type (e.g. microswitch) endstop for low end on Y via pin !io6.in
M574 Z1 S2                                       ; configure Z-probe endstop for low end on Z

; Z-Probe
M558 P8 C"121.io0.in" H5 F120 T6000              ; set Z probe type to unmodulated and the dive height + speeds
G31 P500 X-18.4 Y-5.4 Z1.601                     ; set Z probe trigger value, offset and trigger height hot (60C) Z1.700
M557 X20:280 Y20:280 P5                          ; define mesh grid 5x5

; Heaters
M308 S0 P"temp0" Y"thermistor" A"Bed" T100000 B3950    ; configure sensor 0 as thermistor on pin temp0
M950 H0 C"out0" T0                               ; create bed heater output on out0 and map it to sensor 0
M307 H0 B0 S1.00                                 ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0                                          ; map heated bed to heater 0
M143 H0 S120                                     ; set temperature limit for heater 0 to 120C
M308 S1 P"121.temp0" Y"thermistor" A"Hotend" T100000 B4725 C7.060000e-8; configure sensor 1 as thermistor on pin 121.temp0
M950 H1 C"121.out0" T1                           ; create nozzle heater output on 121.out0 and map it to sensor 1
M307 H1 B0 S1.00                                 ; disable bang-bang mode for heater  and set PWM limit
M143 H1 S300                                     ; set temperature limit for heater 1 to 300C

; Fans
M950 F0 C"121.out1" Q500                         ; create fan 0 on pin 121.out1 and set its frequency
M106 P0 C"Nozzle Fan" S0 H-1                     ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"121.out2" Q500                         ; create fan 1 on pin 121.out2 and set its frequency
M106 P1 C"Hotend Fan" S1 H1 T45                  ; set fan 1 value. Thermostatic control is turned on
M950 F2 C"out5" Q500                             ; create fan 2 on pin out5 and set its frequency
M106 P2 C"Duet Mini Fan" S255 H-1                ; set fan 2 value. Thermostatic control is turned off

; Tools
M563 P0 D0 H1 F0 S"Herema XS"                    ; define tool 0
G10 P0 X0 Y0 Z0                                  ; set tool 0 axis offsets
G10 P0 R0 S0                                     ; set initial tool 0 active and standby temperatures to 0C

; Z Axis Leveling
M671 X-52:342 Y150:150 S5                        ; adjust leadscrews at left (40,150) and right (260,150)

; Pressure Advance
M572 D0 S0.023

; Compensation Taper
M376 H10 ; Taper after 10mm

; Accelerometers
;M955 P0 C"io3.out+io3.in" I20                    ; LIS3DH
M955 P121.0 I54                                  ; Toolboard 1LC with CAN address 121                  

; Input Shaping
M593 P"MZV" F38
;M593 p"EI3" F30

; Read stored parameters
M501
T0

; Home, Level and Load Map on Startup
;M98 P"0:/macros/2_Home, Level and Load Map"

;Manual Bed Screws (Old points)
;M671 X0:0:289:289 Y107:207:207:107 P0.7 ; adjusting screws at front left (0,107), rear left (0,207), rear right (289,207) and front right (289,107), thread pitch 0.7mm

; Custom settings are not defined

@dc42, I think I figured it out. I grounded the hotend and frame. It seems to be printing now. I’ve gotten way further in my current print than I was getting before. I’ll know when this 4 hour print finishes that ESD was the issue.

@T3P3Tony, it seems to have fixed it. I’m using a revo hemera xs hotbed with the 1lc board.

I was hoping these would come with the Roto toolboard. Then I wouldn’t have to buy two pieces of hardware. Seems like the beacon footprint is becoming a standard for tool head probe design.

@T3P3Tony

https://github.com/beacon3d/docs/tree/master/mcad/beacon

https://docs.beacon3d.com/installation/

Is possible for a Duet3D to produce a SZP Coil board to be same size as a beacon and/cartographer probe for easy toolhead mount compatibility?

@Charlie Does the iterations variable used in bed.g need to be defined?

Are your LEDs GRBW vs RGBW for color order?

If you try and send green to the light is it red?

@Mr-Crispin I couldn’t find anything on there. Do you happened to know their username?

@Mr-Crispin Do you be chance have a mount for the roto tool board for the voron that you'd be willing to share?

@dc42
Newest version works with IS on. It was quieter during infills, as well. Thanks for all your work

@NeoDue Testing... Fingers crossed

Update: 35% finished, so far no shifting... I have few more hours to go to complete the print.
Update 2: 46% and going strong...

Checked this morning: finished correctly

Working for me

@dc42
I’ll try and test tomorrow with the upcoming version