Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login
    1. Home
    2. Anawandur
    • Profile
    • Following 0
    • Followers 0
    • Topics 8
    • Posts 18
    • Best 1
    • Controversial 0
    • Groups 0

    Anawandur

    @Anawandur

    1
    Reputation
    4
    Profile views
    18
    Posts
    0
    Followers
    0
    Following
    Joined Last Online

    Anawandur Unfollow Follow

    Best posts made by Anawandur

    • RE: First layer is not evenly closed

      I have now replaced the IR sensor with the BL-Touch and the problem is gone. I think that the different shades on the printing plates caused these errors when using the IR sensors.

      posted in Tuning and tweaking
      Anawandurundefined
      Anawandur

    Latest posts made by Anawandur

    • Problems with preheating (IDEX) (Preheat Macro)

      Hello,
      I have a reference to a preheat macro in the start.g file of my IDEX printer, which always heats the print bed according to the loaded filament. At the end of start.g, there's also a T0 command.
      In my slicer, I sliced a part with T0. In the DWC, PETG is loaded for T0, and PLA is loaded for T1.
      When I start the print, the printer first preheats for T1 (PLA), then for T0 (PETG), and finally executes the slicer start code.
      I think the problem is that, in the start.g file, the information about which tool will be used is not yet available, which causes this confusion. If I load the same filament for both tools, there’s no issue, of course. Does anyone understand my problem and maybe have a solution for it?

      Thanks and best regards!

      Start.g

      M291 P"Start.g wird ausgeführt" S0
      if !move.axes[0].homed || !move.axes[1].homed || !move.axes[2].homed
        G28
      M98 P"/Macros/SUB/CheckDoor"          ;Prüfung ob die Tür entsprechend zum Material geöffnet oder geschlossen sein muss
      M561                                  
      M703                                  
      M106 P3 S255                           ; LED schalten 25%
      M98 P"/Macros/SUB/Preheat"            ; Vorheizen Macro
      G28 Z0                                ; Z Homen
      M98 P"/Macros/Buildplate_Z-Offset"    ;Z-Offset der entsprechenden Platte
      T0
      

      Preheat Macro

      if (move.extruders[0].filament == "PLA" || move.extruders[1].filament == "PLA") 
         G4 S1
         M300 S600 P100
         G4 S2
         M300 S600 P100
         M291 P"PLA 60°C" R"Es wird für PLA vorgeheizt" S0 T4
         G4 S5
         M106 P4 S255 ;Gehäuse Lüfter
         M190 S60
         M116 H0.5
      
      if (move.extruders[0].filament == "PETG" || move.extruders[1].filament == "PETG") 
         G4 S1
         M300 S500 P100
         G4 S2
         M300 S800 P100
         M291 P"PETG 85°C" R"Es wird für PETG vorgeheizt" S0 T4
         G4 S5
         M106 P4 S120 ;Gehäuse Lüfter
         M190 S85
         M116 H0.5
      
      
      if (move.extruders[0].filament == "ASA" || move.extruders[1].filament == "ASA") 
         M300 S500 P100
         G4 S2
         M300 S800 P100
         M291 P"ASA 85°C" R"Es wird für ASA vorgeheizt" S0 T4
         G4 S5
         M106 P4 S120 ;Gehäuse Lüfter
         M190 S85
         M116 H0.5
      
      if (move.extruders[0].filament == "PP" || move.extruders[1].filament == "PP") 
         M300 S500 P100
         G4 S2
         M300 S800 P100
         M291 P"PP 80°C" R"Es wird für PP vorgeheizt" S0 T4
         G4 S5
         M106 P4 S25 ;Gehäuse Lüfter
         M190 S80
         M116 H0.5   
      if (move.extruders[0].filament == "PA12CF" || move.extruders[1].filament == "PA12CF") 
         M300 S500 P100
         G4 S2
         M300 S800 P100
         M291 P"PA12CF 90°C" R"Es wird für PA12CF vorgeheizt" S0 T4
         G4 S5
         M106 P4 S120 ;Gehäuse Lüfter
         M190 S90
         M116 H0.5   
      
      posted in Tuning and tweaking
      Anawandurundefined
      Anawandur
    • RE: First layer is not evenly closed

      I have now replaced the IR sensor with the BL-Touch and the problem is gone. I think that the different shades on the printing plates caused these errors when using the IR sensors.

      posted in Tuning and tweaking
      Anawandurundefined
      Anawandur
    • RE: First layer is not evenly closed

      I did a few more tests today. I have different printing plates. On my BlackPrint FR4 (black) I have different mattings due to previous prints or scratched surfaces, which apparently has a big impact on the IR probe.

      In the following photo you can see a matting strip, that's exactly where the IR probe measured and found .0.9mm.

      PXL_20240915_160038324.jpg
      .
      Screenshot 2024-09-15 172412.png

      Then I took a measurement on a BuildTag. There is white writing on the bottom left and in the middle there are marks from an old print. This is also reflected in the heightmap.
      PXL_20240915_162529314.jpg
      .
      Screenshot 2024-09-15 182712.png

      posted in Tuning and tweaking
      Anawandurundefined
      Anawandur
    • RE: First layer is not evenly closed

      @gloomyandy I've already tried it with 15 points. If I use more points, the first layer becomes even more uneven. With 3x3 I get a better result than with 7x7.

      I think I have specified the offset correctly, the IR sensor is located at the back right.
      PXL_20240915_143117183.jpg

      Home.z

      T-1 P0 
      G91 ; relative mode
      G1 H2 Z4 F2000 ; raise head 4mm to ensure it is above the Z probe trigger height
      G90 ; back to absolute mode
      G1 H2 X170 Y110 F6000 ; put head over the centre of the bed, or wherever you want to probe
      M558 F400
      G30 ; lower head, stop when probe triggered and set Z to trigger height
      G1 H0 Z5 F250
      M558 F50 A9 S0.003
      G30
      M558 F200 A1
      G1 H1 X-350 U355 Y-2 F3000
      
      posted in Tuning and tweaking
      Anawandurundefined
      Anawandur
    • RE: First layer is not evenly closed

      @Phaedrux I created this mesh directly before printing. Since I have big problems with the first layer, the bed is leveled with a macro and the Heightmap.csv is created. Depending on the loaded build plate and filament type, the map is then written to example: Blackprintheightmap60°c, which is then loaded into start.g.

      posted in Tuning and tweaking
      Anawandurundefined
      Anawandur
    • RE: First layer is not evenly closed

      @dc42 My macro buildplate is loaded in start.g, in which the correct mesh and Z-offset are loaded according to the filament and loaded print plate.

      start.g

      M291 P"Start.g starting" S0
      if !move.axes[0].homed || !move.axes[1].homed || !move.axes[2].homed
        G28
      M98 P"/Macros/SUB/CheckDoor"          ;Check whether the door must be opened or closed according to the material
      M561                                  ; Disable Mesh Bed Kompensation
      M106 P3 S25                           ; LED 25%
      M98 P"/Macros/SUB/Preheat"            ; Heat Makro
      G28 Z0                                ; Z Home
      M98 P"/Macros/Buildplate"            ;Load buildplate including mesh according to the print plate and take Z-offset into account.
      

      Macros/Buildplate

      ; check if BuildTak selected is
      if global.buildplate_type == 1
          echo "BuildTak is selected"
          if (move.extruders[0].filament == "PLA" || move.extruders[1].filament == "PLA") 
             G4 S1
             M291 P"BuildTak  PLA 60°C" R"Heightmap loaded" S0 T4
             M290 R0 S0    ; Reset baby steps
             M300 S800 P1000
             G29 S1 P"BuildTakheightmap60c.csv"
             ;G4 S2 
             ;M290 S-0.20                                                   ; Baby Stepp is setting
             ;echo "Babystep for Buildtak is 0.04mm"
      
      
          if (move.extruders[0].filament == "PETG" || move.extruders[1].filament == "PETG") 
             G4 S1
             M291 P"BuildTak  PETG 70°C" R"Heightmap loaded" S0 T4
             M290 R0 S0    ; Reset baby steps
             M300 S800 P1000
             G29 S1 P"BuildTakheightmap70c.csv"
             ;G4 S2 
             ;M290 S0.04                                                   ; Baby Stepp is setting
             ;echo "Babystep for Buildtak is 0.04mm"
      
      
      
          if (move.extruders[0].filament == "ASA" || move.extruders[1].filament == "ASA") 
             G4 S1
             M291 P"BuildTak  ASA 100°C" R"Heightmap loaded" S0 T4
             M290 R0 S0    ; Reset baby steps
             M300 S800 P1000
             G29 S1 P"BuildTakheightmap100c.csv"
             ;G4 S2 
             ;M290 S0.04                                                   ; Baby Stepp is setting
             ;echo "Babystep for Buildtak is 0.04mm"
      
      
          if (move.extruders[0].filament == "PA12CF" || move.extruders[1].filament == "PA12CF") 
             G4 S1
             M291 P"BuildTak  PA12CF 90°C" R"Heightmap loaded" S0 T4
             M290 R0 S0    ; Reset baby steps
             M300 S800 P1000
             G29 S1 P"BuildTakheightmap90c.csv"
             ;G4 S2 
             ;M290 S0.04                                                   ; Baby Stepp is setting
             ;echo "Babystep for Buildtak is 0.04mm"
      ;---------------------------------------------------------------------------------------------------------------------------------------        
      ;check if PEIglatt selected is
      if global.buildplate_type == 2
          echo "PEIglatt is selected"
          if (move.extruders[0].filament == "PLA" || move.extruders[1].filament == "PLA") 
             G4 S1
             M291 P"PEIglatt  PLA 60°C" R"Heightmap loaded" S0 T4
             M290 R0 S0    ; Reset baby steps
             M300 S800 P1000
             G29 S1 P"PEIglattheightmap60c.csv"
             ;G4 S2 
             ;M290 S0.04                                                   ; Baby Stepp is setting
             ;echo "Babystep for PEIglatt is 0.04mm"
      
          if (move.extruders[0].filament == "PETG" || move.extruders[1].filament == "PETG") 
             G4 S1
             M291 P"PEIglatt  PETG 70°C" R"Heightmap loaded" S0 T4
             M290 R0 S0    ; Reset baby steps
             M300 S800 P1000
             G29 S1 P"PEIglattheightmap70c.csv"
             ;G4 S2 
             ;M290 S-0.20                                                   ; Baby Stepp is setting
             ;echo "Babystep for PEIglatt is -0.20mm"
      
          if (move.extruders[0].filament == "ASA" || move.extruders[1].filament == "ASA") 
             G4 S1
             M291 P"PEIglatt  ASA 100°C" R"Heightmap loaded" S0 T4
             M290 R0 S0    ; Reset baby steps
             M300 S800 P1000
             G29 S1 P"PEIglattheightmap100c.csv"
             ;G4 S2 
             ;M290 S0.04                                                   ; Baby Stepp is setting
             ;echo "Babystep for PEIglatt is 0.04mm"
      
      
          if (move.extruders[0].filament == "PA12CF" || move.extruders[1].filament == "PA12CF") 
             G4 S1
             M291 P"Peiglatt  PA12CF 90°C" R"Heightmap loaded" S0 T4
             M290 R0 S0    ; Reset baby steps
             M300 S800 P1000
             G29 S1 P"PEIglatthighmap90c.csv"
             ;G4 S2 
             ;M290 S0.04                                                   ; Baby Stepp is setting
             ;echo "Babystep for Buildtak is 0.04mm"       
      ;---------------------------------------------------------------------------------------------------------------------------------------   
      ; check if FR4dünn selected is
      if global.buildplate_type == 3
          echo "FR4dünn is selected"
          if (move.extruders[0].filament == "PLA" || move.extruders[1].filament == "PLA") 
             G4 S1
             M291 P"FR4dünn  PLA 60°C" R"Heightmap loaded" S0 T4
             M290 R0 S0    ; Reset baby steps
             M300 S800 P1000
             G29 S1 P"FR4dünnheightmap60c.csv"
             G4 S2 
             M290 S0.20                                                   ; Baby Stepp is setting
             echo "Babystep for FR4dünn PLA is +0.20 mm"
      
      
          if (move.extruders[0].filament == "PETG" || move.extruders[1].filament == "PETG") 
             G4 S1
             M290 R0 S0    ; Reset baby steps
             M291 P"FR4dünn  PETG 85°C" R"Heightmap loaded" S0 T4
             M300 S800 P1000
             G29 S1 P"FR4dünnheightmap85c.csv"
             G4 S2
             M290 S0.20                                                          ; Baby Stepp is setting
             ;M300 S2000 P1000                                                
             echo "Babystep for FR4dünn PETG is +0.20 mm"
      
          if (move.extruders[0].filament == "ASA" || move.extruders[1].filament == "ASA") 
             G4 S1
             M291 P"FR4dünn  ASA 85°C" R"Heightmap loaded" S0 T4
             M290 R0 S0    ; Reset baby steps
             M300 S800 P1000
             G29 S1 P"FR4dünnheightmap100c.csv"
             G4 S2
             M290 S0.20                                                  ; Baby Stepp is setting
             echo "Babystepp für FR4dünn ASA is +0.20 mm"
      
      
          if (move.extruders[0].filament == "PA12CF" || move.extruders[1].filament == "PA12CF") 
             G4 S1
             M291 P"FR4dünn  PA12CF 90°C" R"Heightmap loaded" S0 T4
             M290 R0 S0    ; Reset baby steps
             M300 S800 P1000
             G29 S1 P"FR4dünnheightmap90c.csv"
             G4 S2 
             M290 S0.20                                                   ; Baby Stepp is setting
             echo "Babystep for FR4dünn PA12CF is +0,12 mm"
      ;---------------------------------------------------------------------------------------------------------------------------------------   
      ; check if BlackPrint selected is
      if global.buildplate_type == 4
          echo "BlackPrint is selected"
          if (move.extruders[0].filament == "PLA" || move.extruders[1].filament == "PLA") 
             G4 S1
             M291 P"BlackPrint  PLA 60°C" R"Heightmap loaded" S0 T4
             M290 R0 S0    ; Reset baby steps
             M300 S800 P1000
             G29 S1 P"BlackPrintheightmap60c.csv"
             ;G4 S2 
             ;M290 S-0.12                                                   ; Baby Stepp is setting
             ;echo "Babystepp für BlackPrint is -0.12mm"
      
          if (move.extruders[0].filament == "PETG" || move.extruders[1].filament == "PETG") 
             G4 S1
             M290 R0 S0    ; Reset baby steps
             M291 P"BlackPrint  PETG 85°C" R"Heightmap loaded" S0 T4
             M300 S800 P1000
             G29 S1 P"BlackPrintheightmap85c.csv"
             ;G4 S2
             ;M290 S-0.12                                                          ; Baby Stepp is setting
             ;M300 S2000 P1000                                                
             ;echo "Babystepp für BlackPrint is -0.12mm"
      
          if (move.extruders[0].filament == "ASA" || move.extruders[1].filament == "ASA") 
             G4 S1
             M291 P"BlackPrint  ASA 85°C" R"Heightmap loaded" S0 T4
             M290 R0 S0    ; Reset baby steps
             M300 S800 P1000
             G29 S1 P"BlackPrintheightmap100c.csv"
             ;G4 S2
             ;M290 S-0.12                                                  ; Baby Stepp is setting
             ;echo "Babystepp für BlackPrint is -0.12mm"
      
          if (move.extruders[0].filament == "PA12CF" || move.extruders[1].filament == "PA12CF") 
             G4 S1
             M291 P"BlackPrint  PA12CF 90°C" R"Heightmap loaded" S0 T4
             M290 R0 S0    ; Reset baby steps
             M300 S800 P1000
             G29 S1 P"BlackPrintheightmap90c.csv"
             ;G4 S2 
             ;M290 S0.04                                                   ; Baby Stepp is setting
             ;echo "Babystep for Buildtak is 0.04mm"   
      

      98ec76da-c2cd-4988-9f2c-51da70b2aea6-image.png

      posted in Tuning and tweaking
      Anawandurundefined
      Anawandur
    • RE: Bed Leveling only on Print Aerea

      @jay_s_uk Thank you very much, this works very well.

      posted in Tuning and tweaking
      Anawandurundefined
      Anawandur
    • No sharp corners

      Hello everyone,

      I have converted my Raise3d E2 to a Duet mini5 and 2 LC1 Toolboards and IR Z-Probe and have 2 problems that I cannot solve.

      RepRapFirmware 3.6.0-alpha.4+3

      I would like to describe problem 2 here and I have opened a new entry for the first one.
      Link to Problem 1

      I have configured my input shaper and came up with a value of M593 F51 S0.2 P"zvddd". I determined my pressure advance to be M572 D0 S0.065.

      I always have dirty corners when printing square components. It doesn't matter whether I turn pressure advance on or off. Even a test from 0 to 0.2 didn't bring any improvement to the corners.

      I have already found older entries in the forum but still no solution.

      Can anyone help?

      config.g

      ; Configuration file for Duet 3 Mini 5+ (firmware version 3.3)
      ; executed by the firmware on start-up
      ;
      ; generated by RepRapFirmware Configuration Tool v3.3.15 on Sat Nov 26 2022 13:27:47 GMT+0100 (Mitteleuropäische Normalzeit)
      
      ;###########################################################################################################################
      ; General preferences
      ;###########################################################################################################################
      M575 P1 S1 B57600                                        ; enable support for PanelDue
      G90                                                      ; send absolute coordinates...
      M83                                                      ; ...but relative extruder moves
      M550 P"Raise 3D E2"                                      ; set printer name
      
      ;##########################################################################################################################
      ; Network
      ;##########################################################################################################################
      M552 S1                                                  ; enable network
      M586 P0 S1                                               ; enable HTTP
      M586 P1 S1                                               ; disable FTP
      M586 P2 S0                                               ; disable Telnet
      
      ;##########################################################################################################################
      ; Drives
      ;##########################################################################################################################
      M569 P0.0 S0 D3 H50 V30                                  ; physical drive 0.0 goes forwards
      M915 P0.0 T50
      
      M569 P0.1 S0 D3 H50 V30                                  ; physical drive 0.1 goes forwards
      M915 P0.1 T30
      
      M569 P0.2 S0 D3 H50 V30                                  ; physical drive 0.2 goes forwards
      M915 P0.2 T50
      
      M569 P20.0 S0                                            ; physical drive 0.3 goes forwards Extruder links
      
      M569 P0.4 S0 D3 H50 V30                                  ; physical drive 0.4 goes forwards
      M915 P0.4 T50
      
      M569 P21.0 S1                                            ; physical drive 0.5 goes forwards
      
      M584 X0.0 Y0.1 Z0.2 E20.0:21.0 U4                        ; set drive mapping
      M350 X16 Y16 U16 Z16 E16:16 I1                           ; configure microstepping without interpolation
      M92 X80 Y80 U80 Z800 E286.216 :286.216                   ; set steps per mm linker Extruder : rechter Extroder
      M566 X600 Y600 U600 Z30 E300:300                         ; set maximum instantaneous speed changes (mm/min)
      M203 X10000 U10000 Y9000 Z600 E3000:3000                ; set maximum speeds (mm/min)
      M201 X1500 U1500 Y1500 Z120 E3000:3000                    ; set accelerations (mm/s^2)
      ;M906 X850 U850 Y850 Z800 E800:800 I30                    ; set motor currents (mA) and motor idle factor in per cent
      M906 X1200 U1200 Y1200 Z900 E800:800 I30                    ; set motor currents (mA) and motor idle factor in per cent
      M84 S30                                                  ; Set idle timeout
      
      ;##########################################################################################################################
      ; Axis Limits
      ;##########################################################################################################################
      M208 X10 Y-3 Z0 U35 S1                                   ; set axis minima
      M208 X335 Y255 Z240 U355 S0                              ; set axis maxima
      
      ;##########################################################################################################################
      ; Endstops                                               ; configure switch-type (e.g. microswitch) endstop for high end on Z via pin null
      ;##########################################################################################################################
      M574 Y1 S1 P"io1.in"
      M574 X1 S1 P"io2.in"
      M574 U2 S1 P"Io4.in"
      ;M915 X S-63 H10 R1                                      ; Set very sensitive stall detect
      ;M574 X1 S3                                              ; configure endstop for stall detection
      ;M915 X S20 H140 R0                                      ; Set very sensitive stall detect
      ;M915 X S-63 H10 R1                                      ; Set very sensitive stall detect
      
      ;##########################################################################################################################
      ; Switch
      ;##########################################################################################################################
      M950 J1 C"SPI.CS2"
      ;M581 P1 S0 T5 R0                                        ;Alarm wenn tür beim drucken geöffnet wird
      ;M581 P1 S1 T6 R0                                        ;TEST war vorher nicht drin
      
      ;##########################################################################################################################
      ; Filament Sensoren
      ;##########################################################################################################################
      M591 D1 P1 C"io6.in" S1
      M591 D0 P1 C"io5.in" S1
      
      ;##########################################################################################################################
      ; Z-Probe
      ;##########################################################################################################################
      M558 P8 C"20.io0.in" H5 A7 S0.008 F200 T10000            ; P=Sondentyp C=Eingangspin H=Anfahrhöhe A=Anzahl Tastvorgänge S=Tolleranz (Standard 0,03) F=Abtastgeschwindigkeit T=Verfahrgeschwindigkeit 
      G31 P500 X17 Y21 Z1.30                                  ; set Z probe trigger value, offset and trigger height + Tiefer - höher
      M557 X31:335 Y20:225 P7                                  ; define mesh grid
      
      ;##########################################################################################################################
      ;Acclerometer
      ;##########################################################################################################################
      M955 P20.0 I24                ; configure accelerometer on toolboard with CAN address 121 and specify orientation 
      M593 F51 S0.2  P"zvddd"
      M955 P21.0 I24                ; configure accelerometer on toolboard with CAN address 121 and specify orientation 
      
      
      ;##########################################################################################################################
      ; Heaters
      ;##########################################################################################################################
      M308 S0 P"Temp0" Y"thermistor" T100000 B4138             ; configure sensor 0 as thermistor on pin temp0
      M950 H0 C"out0" T0                                       ; create bed heater output on out0 and map it to sensor 0
      M307 H0 B1 S1.00                                         ; enable bang-bang mode for the bed heater and set PWM limit
      M140 H0                                                  ; map heated bed to heater 0
      M143 H0 S120                                             ; set temperature limit for heater 0 to 120C
      
      M308 S2 P"21.Temp0" Y"thermistor" T100000 B4725 C7.06e-8 ; configure sensor 2 as thermistor on pin temp2
      M950 H2 C"21.out0" T2                                    ; create nozzle heater output on out2 and map it to sensor 2
      M307 H2 B0 S1.00                                         ; disable bang-bang mode for heater  and set PWM limit
      M143 H2 S340                                             ; set temperature limit for heater 2 to 340C
      
      M308 S1 P"20.Temp0" Y"thermistor" T100000 B4725 C7.06e-8 ; configure sensor 2 as thermistor on pin temp2
      M950 H1 C"20.out0" T1                                    ; create nozzle heater output on out2 and map it to sensor 2
      M307 H1 B0 S1.00                                         ; disable bang-bang mode for heater  and set PWM limit
      M143 H1 S340                                             ; set temperature limit for heater 2 to 340C
      
      ;##########################################################################################################################
      ; Temp Sensoren
      ;##########################################################################################################################
      M308 S10 Y"mcu-temp" A"MCU"                              ; defines sensor 10 as MCU temperature sensor
      M308 S11 Y"drivers" A"Duet stepper drivers"              ; defines sensor 11 as stepper driver temperature sensor
      ;M950 F5 C"out6" Q500                                    ; create fan 2 on pin fan2 and set its frequency
      ;M106 P5 H3 T40:70                                       ; set fan 2 value
      
      ;##########################################################################################################################
      ; Fans
      ;##########################################################################################################################
      ;M950 F0 C"vfd" Q500                                     ; create fan 0 on pin out4 and set its frequency
      ;M106 P0 C"Bauteil-Lüfter L" S0 H-1
      
      M950 F0 C"20.out1" Q500
      M106 P0 C"Bauteil-Lüfter L" S0 H-1
      
      M950 F1 C"21.out1" Q500
      M106 P1 C"Bauteil-Lüfter R" S0 H-1
      
      M950 F3 C"out5" Q500                                     ; create fan 2 on pin vfd and set its frequency
      M106 P3 C"LED" S150 H-1                                  ; set fan 2 value. Thermostatic control is turned off
      
      M950 F4 C"out4+out4.tach" Q25000
      M106 P4 C"Filter-Lüfter" S0 H-1
      
      M950 F5 C"21.out2" Q500                                  ; create fan 0 on pin out3 and set its frequency
      M106 P5 C"Hotend Fan rechts" S1 H2 T45                   ; set fan 0 name and value. Thermostatic control turned on for Hotend
      M950 F6 C"20.out2" Q500                                  ; create fan 0 on pin out3 and set its frequency
      M106 P6 C"Hotend Fan links" S1 H1 T45                                          
      
      ;##########################################################################################################################
      ; Create a tool that uses the low end (X) carriage
      ;##########################################################################################################################
      M563 P0 D0 H1 F0  S"linker Extruder"                     ; tool 0 uses extruder 0, heater 1 and fan 0 (P=Werkzeug Nr., S=Name, D=Extruder Motor, H=Heizung, F=Bautellüfter)
      G10 P0 X0 Y0 Z0 S0 R0                                    ; set tool 0 offsets and temperatures
      
      ;##########################################################################################################################
      ; Create a tool that uses the high end (U) carriage
      ;##########################################################################################################################
      M563 P1 D1 H2 X3 F1  S"rechter Extruder"                 ; tool 1 uses extruder 1, heater 2, fan 2, and maps X to U
      G10 P1 Y0.1 U26.6 Z0.02 R0                               ; set tool 1 offsets and temperatures für Z: + Tiefer - höher U: - weiter nach rechts + weiter nach links (G10 P1 Y0 U27.0 Z0.02 R0)   
      
      ;##########################################################################################################################
      ; Create a tool that prints 2 copies of the object using both carriages
      ;##########################################################################################################################
      
      M563 P2 D0:1 H1:2 X0:3 F0:0 S"Duplikation"               ; tool 2 uses both extruders, hot end heaters and fans, and maps X to both X and U
      G10 P2 X-25 Y0 U-176.3 Z0 S0 R0                          ; set tool offsets and temperatures
      ;G10 P2 X10 Y0 U-176.3 Z0 S0 R0                             ; set tool offsets and temperatures
      ;G10 P2 X0 Y0 U-40 Z0 S0 R0                              ; set tool offsets and temperatures
      G10 P2 R0 S0
      M567 P2 E1:1                                             ; set mix ratio 100% on both extruders
      
      ;##########################################################################################################################
      ;Create a tool that Prints in Mirrior Mode
      ;##########################################################################################################################
      
      ;M563 P3 H1:2 D0:1 X0:3 F0:0 S"Spiegeln"
      ;G10 P3 X-25 Y0 U-176.3 Z0 S0 R0
      ;G10 P3 R0 S-2
      
      ;##########################################################################################################################
      ; Custom settings are not defined
      ;##########################################################################################################################
      ;##########################################################################################################################
      ;Temperatur anpassung MCU
      ;##########################################################################################################################
      M912 P0 S2
      ;##########################################################################################################################
      ; Miscellaneous
      ;##########################################################################################################################
      M501                                                     ; load saved parameters from config-override.g
      M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000"       ; set voltage thresholds and actions to run on power loss
      M98 P"GlobaleBuildplate.g"
      G4 S2                                                    ; wait for expansion boards to start
      

      PA TEST 0 to 0.2
      PXL_20240902_152445068.jpg

      PXL_20240902_152419180.jpg

      PXL_20240902_152429278.jpg

      posted in Tuning and tweaking
      Anawandurundefined
      Anawandur
    • First layer is not evenly closed

      Hello everyone,

      I have converted my Raise3d E2 to a Duet mini5 and 2 LC1 Toolboards and IR Z-Probe and have 2 problems that I cannot solve.

      I would like to describe problem 1 here and I will open a new entry for the second. Link to problem 2

      The first problem is that my first layer is not evenly closed. When I print one layer (180x180 mm) the first layer has a thickness of between 0.18mm and 0.26mm. The hardware on the printer is very solid and has no problems. I did not have these problems before the conversion either. Perhaps someone can give me tips on where I could look for the error.

      My bed leveling is controlled by a macro that creates a Heightmap.csv depending on the print plate and filament used and then saves this in a BlackPrint 60°C file, which is called up in Start.g when printing.

      RepRapFirmware 3.6.0-alpha.4+3

      config.g:

      ; Configuration file for Duet 3 Mini 5+ (firmware version 3.3)
      ; executed by the firmware on start-up
      ;
      ; generated by RepRapFirmware Configuration Tool v3.3.15 on Sat Nov 26 2022 13:27:47 GMT+0100 (Mitteleuropäische Normalzeit)
      
      ;###########################################################################################################################
      ; General preferences
      ;###########################################################################################################################
      M575 P1 S1 B57600                                        ; enable support for PanelDue
      G90                                                      ; send absolute coordinates...
      M83                                                      ; ...but relative extruder moves
      M550 P"Raise 3D E2"                                      ; set printer name
      
      ;##########################################################################################################################
      ; Network
      ;##########################################################################################################################
      M552 S1                                                  ; enable network
      M586 P0 S1                                               ; enable HTTP
      M586 P1 S1                                               ; disable FTP
      M586 P2 S0                                               ; disable Telnet
      
      ;##########################################################################################################################
      ; Drives
      ;##########################################################################################################################
      M569 P0.0 S0 D3 H50 V30                                  ; physical drive 0.0 goes forwards
      M915 P0.0 T50
      
      M569 P0.1 S0 D3 H50 V30                                  ; physical drive 0.1 goes forwards
      M915 P0.1 T30
      
      M569 P0.2 S0 D3 H50 V30                                  ; physical drive 0.2 goes forwards
      M915 P0.2 T50
      
      M569 P20.0 S0                                            ; physical drive 0.3 goes forwards Extruder links
      
      M569 P0.4 S0 D3 H50 V30                                  ; physical drive 0.4 goes forwards
      M915 P0.4 T50
      
      M569 P21.0 S1                                            ; physical drive 0.5 goes forwards
      
      M584 X0.0 Y0.1 Z0.2 E20.0:21.0 U4                        ; set drive mapping
      M350 X16 Y16 U16 Z16 E16:16 I1                           ; configure microstepping without interpolation
      M92 X80 Y80 U80 Z800 E286.216 :286.216                   ; set steps per mm linker Extruder : rechter Extroder
      M566 X600 Y600 U600 Z30 E300:300                         ; set maximum instantaneous speed changes (mm/min)
      M203 X10000 U10000 Y9000 Z600 E3000:3000                ; set maximum speeds (mm/min)
      M201 X1500 U1500 Y1500 Z120 E3000:3000                    ; set accelerations (mm/s^2)
      ;M906 X850 U850 Y850 Z800 E800:800 I30                    ; set motor currents (mA) and motor idle factor in per cent
      M906 X1200 U1200 Y1200 Z900 E800:800 I30                    ; set motor currents (mA) and motor idle factor in per cent
      M84 S30                                                  ; Set idle timeout
      
      ;##########################################################################################################################
      ; Axis Limits
      ;##########################################################################################################################
      M208 X10 Y-3 Z0 U35 S1                                   ; set axis minima
      M208 X335 Y255 Z240 U355 S0                              ; set axis maxima
      
      ;##########################################################################################################################
      ; Endstops                                               ; configure switch-type (e.g. microswitch) endstop for high end on Z via pin null
      ;##########################################################################################################################
      M574 Y1 S1 P"io1.in"
      M574 X1 S1 P"io2.in"
      M574 U2 S1 P"Io4.in"
      ;M915 X S-63 H10 R1                                      ; Set very sensitive stall detect
      ;M574 X1 S3                                              ; configure endstop for stall detection
      ;M915 X S20 H140 R0                                      ; Set very sensitive stall detect
      ;M915 X S-63 H10 R1                                      ; Set very sensitive stall detect
      
      ;##########################################################################################################################
      ; Switch
      ;##########################################################################################################################
      M950 J1 C"SPI.CS2"
      ;M581 P1 S0 T5 R0                                        ;Alarm wenn tür beim drucken geöffnet wird
      ;M581 P1 S1 T6 R0                                        ;TEST war vorher nicht drin
      
      ;##########################################################################################################################
      ; Filament Sensoren
      ;##########################################################################################################################
      M591 D1 P1 C"io6.in" S1
      M591 D0 P1 C"io5.in" S1
      
      ;##########################################################################################################################
      ; Z-Probe
      ;##########################################################################################################################
      M558 P8 C"20.io0.in" H5 A7 S0.008 F200 T10000            ; P=Sondentyp C=Eingangspin H=Anfahrhöhe A=Anzahl Tastvorgänge S=Tolleranz (Standard 0,03) F=Abtastgeschwindigkeit T=Verfahrgeschwindigkeit 
      G31 P500 X17 Y21 Z1.30                                  ; set Z probe trigger value, offset and trigger height + Tiefer - höher
      M557 X31:335 Y20:225 P7                                  ; define mesh grid
      
      ;##########################################################################################################################
      ;Acclerometer
      ;##########################################################################################################################
      M955 P20.0 I24                ; configure accelerometer on toolboard with CAN address 121 and specify orientation 
      M593 F51 S0.2  P"zvddd"
      M955 P21.0 I24                ; configure accelerometer on toolboard with CAN address 121 and specify orientation 
      
      
      ;##########################################################################################################################
      ; Heaters
      ;##########################################################################################################################
      M308 S0 P"Temp0" Y"thermistor" T100000 B4138             ; configure sensor 0 as thermistor on pin temp0
      M950 H0 C"out0" T0                                       ; create bed heater output on out0 and map it to sensor 0
      M307 H0 B1 S1.00                                         ; enable bang-bang mode for the bed heater and set PWM limit
      M140 H0                                                  ; map heated bed to heater 0
      M143 H0 S120                                             ; set temperature limit for heater 0 to 120C
      
      M308 S2 P"21.Temp0" Y"thermistor" T100000 B4725 C7.06e-8 ; configure sensor 2 as thermistor on pin temp2
      M950 H2 C"21.out0" T2                                    ; create nozzle heater output on out2 and map it to sensor 2
      M307 H2 B0 S1.00                                         ; disable bang-bang mode for heater  and set PWM limit
      M143 H2 S340                                             ; set temperature limit for heater 2 to 340C
      
      M308 S1 P"20.Temp0" Y"thermistor" T100000 B4725 C7.06e-8 ; configure sensor 2 as thermistor on pin temp2
      M950 H1 C"20.out0" T1                                    ; create nozzle heater output on out2 and map it to sensor 2
      M307 H1 B0 S1.00                                         ; disable bang-bang mode for heater  and set PWM limit
      M143 H1 S340                                             ; set temperature limit for heater 2 to 340C
      
      ;##########################################################################################################################
      ; Temp Sensoren
      ;##########################################################################################################################
      M308 S10 Y"mcu-temp" A"MCU"                              ; defines sensor 10 as MCU temperature sensor
      M308 S11 Y"drivers" A"Duet stepper drivers"              ; defines sensor 11 as stepper driver temperature sensor
      ;M950 F5 C"out6" Q500                                    ; create fan 2 on pin fan2 and set its frequency
      ;M106 P5 H3 T40:70                                       ; set fan 2 value
      
      ;##########################################################################################################################
      ; Fans
      ;##########################################################################################################################
      ;M950 F0 C"vfd" Q500                                     ; create fan 0 on pin out4 and set its frequency
      ;M106 P0 C"Bauteil-Lüfter L" S0 H-1
      
      M950 F0 C"20.out1" Q500
      M106 P0 C"Bauteil-Lüfter L" S0 H-1
      
      M950 F1 C"21.out1" Q500
      M106 P1 C"Bauteil-Lüfter R" S0 H-1
      
      M950 F3 C"out5" Q500                                     ; create fan 2 on pin vfd and set its frequency
      M106 P3 C"LED" S150 H-1                                  ; set fan 2 value. Thermostatic control is turned off
      
      M950 F4 C"out4+out4.tach" Q25000
      M106 P4 C"Filter-Lüfter" S0 H-1
      
      M950 F5 C"21.out2" Q500                                  ; create fan 0 on pin out3 and set its frequency
      M106 P5 C"Hotend Fan rechts" S1 H2 T45                   ; set fan 0 name and value. Thermostatic control turned on for Hotend
      M950 F6 C"20.out2" Q500                                  ; create fan 0 on pin out3 and set its frequency
      M106 P6 C"Hotend Fan links" S1 H1 T45                                          
      
      ;##########################################################################################################################
      ; Create a tool that uses the low end (X) carriage
      ;##########################################################################################################################
      M563 P0 D0 H1 F0  S"linker Extruder"                     ; tool 0 uses extruder 0, heater 1 and fan 0 (P=Werkzeug Nr., S=Name, D=Extruder Motor, H=Heizung, F=Bautellüfter)
      G10 P0 X0 Y0 Z0 S0 R0                                    ; set tool 0 offsets and temperatures
      
      ;##########################################################################################################################
      ; Create a tool that uses the high end (U) carriage
      ;##########################################################################################################################
      M563 P1 D1 H2 X3 F1  S"rechter Extruder"                 ; tool 1 uses extruder 1, heater 2, fan 2, and maps X to U
      G10 P1 Y0.1 U26.6 Z0.02 R0                               ; set tool 1 offsets and temperatures für Z: + Tiefer - höher U: - weiter nach rechts + weiter nach links (G10 P1 Y0 U27.0 Z0.02 R0)   
      
      ;##########################################################################################################################
      ; Create a tool that prints 2 copies of the object using both carriages
      ;##########################################################################################################################
      
      M563 P2 D0:1 H1:2 X0:3 F0:0 S"Duplikation"               ; tool 2 uses both extruders, hot end heaters and fans, and maps X to both X and U
      G10 P2 X-25 Y0 U-176.3 Z0 S0 R0                          ; set tool offsets and temperatures
      ;G10 P2 X10 Y0 U-176.3 Z0 S0 R0                             ; set tool offsets and temperatures
      ;G10 P2 X0 Y0 U-40 Z0 S0 R0                              ; set tool offsets and temperatures
      G10 P2 R0 S0
      M567 P2 E1:1                                             ; set mix ratio 100% on both extruders
      
      ;##########################################################################################################################
      ;Create a tool that Prints in Mirrior Mode
      ;##########################################################################################################################
      
      ;M563 P3 H1:2 D0:1 X0:3 F0:0 S"Spiegeln"
      ;G10 P3 X-25 Y0 U-176.3 Z0 S0 R0
      ;G10 P3 R0 S-2
      
      ;##########################################################################################################################
      ; Custom settings are not defined
      ;##########################################################################################################################
      ;##########################################################################################################################
      ;Temperatur anpassung MCU
      ;##########################################################################################################################
      M912 P0 S2
      ;##########################################################################################################################
      ; Miscellaneous
      ;##########################################################################################################################
      M501                                                     ; load saved parameters from config-override.g
      M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000"       ; set voltage thresholds and actions to run on power loss
      M98 P"GlobaleBuildplate.g"
      G4 S2                                                    ; wait for expansion boards to start```
      
      

      start.g:

      M291 P"Start.g wird ausgeführt" S0
      if !move.axes[0].homed || !move.axes[1].homed || !move.axes[2].homed
        G28
      M98 P"/Macros/SUB/CheckDoor"
      M561          ; Disable Mesh Bed Kompensation
      G4 S1
      M106 P3 S25   ; LED schalten 25%
      M98 P"/Macros/SUB/Preheat"
      G28 Z0        ; Z Homen
      M98 P"/Macros/Buildplate"
      

      The mesh is then called up via M98 P"/Macros/Buildplate". For example, for the BlackPrint and PLA printing plate it is BlackPrint60°C.csv

      this is my slicer start code:

      T0
      M291 P"Beginne slicer start gcode" S0
      M703                                                         ; load config file for [filament_type]
      G90                                                            ; set printer absolute mode
      M82                                                           ; set extruder to absolute mode
      M106 S0                                                    ; fan off
      M106 P3 S180                                           ; LED an
      T0                                                               ; set first toolhead
      M703                                                         ; load config file for [filament_type]
      G1 Z3 F2000                                              ; Move to Z3 for height clearance before Intro line
      G92 E0                                                       ; set position
      M291 P"Intro Line" S0
      M116 S5
      M400
      ; intro line
      G1 Z0.35 F5000 
      G1 X60 Y-2 F5000
      G1 X150 Y-2 E16 F1000 
      G1 X170 y-2 F5000
      G1 X170 Y0 F5000
      G1 X150 Y0 F500
      G1 X60 Y0 E30 F1000
      G1 X40 Y0 F5000
      G1 Z5 F2000                                              ; Move to Z5 to prevent dragging nozzle and scratching bed
      G92 E0                                                       ; set position
      G1 F2000 
      M117 "Druck wird gestartet"
      
      

      PXL_20240905_152550540.jpg

      PXL_20240904_193601399.jpg

      PXL_20240828_140822085.jpg

      posted in Tuning and tweaking
      Anawandurundefined
      Anawandur
    • RE: Interpreting and setting the IDEX input shaping diagram

      I have now carried out various tests and was able to achieve the best result with 50 Hz ZVDDD

      posted in Tuning and tweaking
      Anawandurundefined
      Anawandur