• Tags
  • Documentation
  • Order
  • Register
  • Login
Duet3D Logo Duet3D
  • Tags
  • Documentation
  • Order
  • Register
  • Login
  1. Home
  2. DannerD3H
  3. Topics
  • Profile
  • Following 0
  • Followers 0
  • Topics 5
  • Posts 26
  • Best 0
  • Controversial 0
  • Groups 0

Topics created by DannerD3H

  • undefined

    Under extrusion after retracts and dimensional errors on Delta

    Tuning and tweaking
    • • 29 Jan 2018, 08:34 • DannerD3H 31 Jan 2018, 20:39
    11
    0
    Votes
    11
    Posts
    1.7k
    Views

    undefined 31 Jan 2018, 20:39

    With large parts you can get away with excessively high temperatures or insufficient cooling because when it prints perimeters, by the time it finishes the first one and starts the second, the first perimeter has cooled sufficiently to become solid. That's why the base of the pyramid is ok. What's happening at the sides is that when the second perimeter is printed, the first one is still molten, so it is being pushed out of place by the second one.

    Solutions:

    1. If using slic3r, set a low speed for "small perimeters". Slic3r has had this setting for at least 4 years, but sadly the other slicers still don't provide it.

    2. Reduce extrusion temperature.

    3. Increase print cooling.

    4. Reduce print speed.

  • undefined

    Yet another cooling question (Cooling of Duet WiFi board)

    Duet Hardware and wiring
    • • 9 Jan 2018, 18:38 • DannerD3H 9 Jan 2018, 21:32
    5
    0
    Votes
    5
    Posts
    1.1k
    Views

    undefined 9 Jan 2018, 21:32

    If it gets above 50C when it is calibrated, then i suggest you add a fan.

  • undefined

    Standby power and turned off PanelDue in standby mode?

    Duet Hardware and wiring
    • • 9 Jan 2018, 18:14 • DannerD3H 9 Jan 2018, 21:25
    5
    0
    Votes
    5
    Posts
    1.1k
    Views

    undefined 9 Jan 2018, 21:25

    Oh it would be really cool if it could be done via firmware in the future, i would be a big fan at least!
    Less spaghetti in my electronics xD

    But until then i guess there is no way around the relay then..

    I will keep my 5V dcdc then. I want to be able to reach the machine over WiFi when in standby mode.

    Once again, Thankyou for the quick and precise response!

  • undefined

    Moving printhead by hand - Generated voltage - Can i damage anything?

    Duet Hardware and wiring
    • • 9 Jan 2018, 18:10 • DannerD3H 10 Jan 2018, 22:30
    6
    0
    Votes
    6
    Posts
    878
    Views

    undefined 10 Jan 2018, 22:30

    Those are useful with DRV8825 drivers but probably not with most other types.

  • undefined

    My DeltaD3H (DIY Delta printer)

    My Duet controlled machine
    • • 9 Jan 2018, 18:02 • DannerD3H 29 Jan 2018, 09:07
    24
    0
    Votes
    24
    Posts
    3.0k
    Views

    undefined 29 Jan 2018, 09:07

    Cool! 🙂

Unless otherwise noted, all forum content is licensed under CC-BY-SA