@phaedrux because my bltouch doesn't deploy my nozzle dive into the bed.

I give it a try with the newer beta.

hello,

my BLTouch doesn't deployed after i paused and stop a print and started a new print.
This happens the second time.

I have a BLTouch V3.1 and a Duet 6HC in SBC Mode with Firmware Duet 3 MB6HC 3.4.0beta7+5 (2022-01-13)

config.g

; Configuration file for Duet WiFi (firmware version 3.3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.3.10 on Mon Dec 27 2021 17:19:28 GMT+0100 (Mitteleuropäische Normalzeit)

; ======== General preferences =========				
M80 C"pson" 									   ; Enable ATX
G90                                                ; send absolute coordinates...
M83                                                ; ...but relative extruder moves
M550 P"duet3"                                      ; set printer name
M669 K1                                            ; select CoreXY mode

; ======== Network ======== 																										
M586 P0 S1                                         ; enable HTTP
M586 P1 S1                                         ; enable FTP
M586 P2 S1                                         ; enable Telnet

; ======= Drives ======== 
M569 P0 S0 D3                                      ; physical drive 0 goes backwards
M569 P1 S0 D3                                      ; physical drive 1 goes backwards
M569 P2 S0                                         ; physical drive 2 goes backwards
M569 P3 S0                                         ; physical drive 3 goes backwards
M569 P4 S0                                         ; physical drive 4 goes backwards
M584 X0 Y1 Z2:3 E4                                 ; set drive mapping
M350 X16 Y16 Z16 E16 I1                            ; configure microstepping with interpolation
M92  X100.00 Y100.00 Z1600.00 E415.00               ; set steps per mm
M566 X900.00 Y900.00 Z60.00 E120.00                ; set maximum instantaneous speed changes (mm/min)
M203 X20000.00 Y20000.00 Z800.00 E1200.00          ; set maximum speeds (mm/min)
M201 X3000.00 Y3000.00 Z200.00 E1000.00            ; set accelerations (mm/s^2)
M204 P2000 T3000								   ; set Printing and Travel Accelations (mm/s^2)
M906 X1500 Y1500 Z1300 E800 I30                     ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                            ; Set idle timeout

; ======== Axis Limits ======== 
M208 X-28 Y-30 Z0 S1                                   ; set axis minima
M208 X336 Y310 Z410 S0                             ; set axis maxima

; ======== Endstops ======== 
M574 X1 S3                                         ; configure sensorless endstop for low end on X
M574 Y1 S3                                         ; configure sensorless endstop for low end on Y
M574 Z1 S2                                         ; configure Z-probe endstop for low end on Z

; ======== Z-Probe ======== 
M950 S0 C"io4.out"                                 ; create servo pin 0 for BLTouch
M558 P9 C"io4.in" H5 F300 T15000 A3                ; set Z probe type to bltouch and the dive height + speeds
G31 P25 X-27.5 Y-21 Z1.959                        ; set Z probe trigger value, offset and trigger height
M557 X10:285 Y10:285 P7:7                            ; define mesh grid

; ======== Independent Z-Leveling ======== 
M671 X-64.74:364.74 Y150:150 S3	F1 				   ; define where are the leadscrew

; ======== Heaters ======== 
M308 S0 P"temp0" Y"thermistor" T100000 B4138     ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"out0" T0                              ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B0 S1.00                                   ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0                                            ; map heated bed to heater 0
M143 H0 S120                                       ; set temperature limit for heater 0 to 120C
M308 S1 P"temp1" Y"thermistor" T100000 B4725 C7.06e-8 ; configure sensor 1 as thermistor on pin temp1
M950 H1 C"out1" T1                               ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00                                   ; disable bang-bang mode for heater  and set PWM limit
M143 H1 S280                                       ; set temperature limit for heater 1 to 280C

; ======== Fans ======== 
M950 F0 C"out8" Q500                               ; create fan 0 on pin fan0 and set its frequency
M106 P0 C"Fan Cooling" S0 H-1                      ; set fan 0 name and value. Thermostatic control is turned off
M950 F1 C"out7" Q500                               ; create fan 1 on pin fan1 and set its frequency
M106 P1 C"Fan Hotend" S1 H1 T45                    ; set fan 1 name and value. Thermostatic control is turned on

; ========  Tools ======== 
M563 P0 D0 H1 F0                                   ; define tool 0
G10 P0 X0 Y0 Z0                                    ; set tool 0 axis offsets
G10 P0 R0 S0                                       ; set initial tool 0 active and standby temperatures to 0C

; ========  Miscellaneous ======== 
M911 S20 R22 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss
T0                                                 ; select first tool

; ======= Machine =======
M950 P2 C"out2" ; define out2 as light
M42 P2 S1 ; Switch Light on on StartUp

M950 J8 C"^io8.in"                                 ; Map io8.in to Emergency Stop
M581 P8 T0 C0 R0                                   ; Configuring Trigger0 (Emergency Stop)
M582 T0						                       ; Check actual State

M575 P1 B57600 S2								   ; Settings for Neopixel Communication

; ======== Sensorless Homing ========
M915 X Y S3 R0 F0 

; ======== Acc Sensor ==========
; M955 P0 C"spi.cs3+spi.cs2" I24
; M593 P"EI3" F65.2  									; use ZVD input shaping to cancel ringing at xx Hz

; ======== Firmware Retraction =========
M207 S0.65 F2400 Z0.0							   ; Firmware Retraction 

; ======== Settings config-override ======== 
M501											   ; Load settings

; ======== Reset Routines ======== 	
M280 P0 S160 									   ; Reset BL-Touch

deploy

; deployprobe.g
; called to deploy a physical Z probe
;
; generated by RepRapFirmware Configuration Tool v3.3.10 on Mon Dec 27 2021 17:19:28 GMT+0100 (Mitteleuropäische Normalzeit)
M280 P0 S160 	; Reset BLTouch
G4 P100			; Wait 100ms
M280 P0 S10 	; deploy BLTouch
G4 P300			; Wait 100ms
M280 P0 S60  	; Touch Switch Mode BLTouch
G4 P200			; Wait 200ms

retract

; retractprobe.g
; called to retract a physical Z probe
;
; generated by RepRapFirmware Configuration Tool v3.3.10 on Mon Dec 27 2021 17:19:28 GMT+0100 (Mitteleuropäische Normalzeit)
M280 P0 S90 ; retract BLTouch

homez.g

; homez.g
; called to home the Z axis
;
; generated by RepRapFirmware Configuration Tool v3.3.10 on Mon Dec 27 2021 17:19:29 GMT+0100 (Mitteleuropäische Normalzeit)
G91            ; relative positioning
G1 H2 Z5 F6000 ; lift Z relative to current position
G90            ; absolute positioning
G1 X177.5 Y171 F6000 ; go to first probe point
M401           ; Deploy Probe for Safety --> Workaround for the moment!?1?!?!??!?!?!
G30            ; home Z by probing the bed

; Uncomment the following lines to lift Z after probing
;G91           ; relative positioning
;G1 Z5 F100    ; lift Z relative to current position
;G90           ; absolute positioning

Does anyone else have these problem?

@droftarts sometime its easy Thanks!

Hello Guys,

Its me again having problems with my emergency stop.I am using a Duet 6HC with a NC Button at the Input Pin io8.in.
If i push or release the button nothing happens.

This is my config.

I do my best to understand and read the documentations. But i can't get i working.

Thanks for your help!

@chrishamm
how do i set up a trigger the reset the controller when i release it again?
I don't understand that to get it working.

Thank you all!

M574 E0 S0			; Set Emergency Stop active high

; Emergency Stop
M581 E0:S1 T2 C0                          	    ; Configure external trigger
                                                    ; When Z stop switch closes, execute sys/trigger2.g
                                                    ; Trigger on rising edge (S1, default), falling edge (S0), ignore input (S-1)
                                                    ; C0 = trigger at any time (default) C1 = only when printing a file from SD

M582 T2						    ; Check actual State

Thats my Config in RRF2.05

The trigger is exactly the same as above

@bearer

I have tried trigger0.
It looks like the same like my actual Setup.
In my opinion the M999 Gcode is not accepted.

At RRF2.05 it isn't a problem with exactly the same setup.

Maybe it has something to do with pullup resistors?

Hello,

At the moment i am upgrading to RRF3.
Now i have a problem with my Emergency Stop.

It is working but the dwc didn't reconnect until i make a second emergency stop at my panelDue
The emergency stop ist a normal NC Push Button and connected to the e0stop input.
It seems for me that the Software Reset doesn't work.

; Emergency Stop
M950 J1 C"e0stop"										  ; create Emergency Stop Input on E0 Input
M581 P1 T2 C0										      ; Invoke Trigger 2 for Emergency Stop
M582 T2													  ; Check if Trigger 2 is okay

``

trigger2.g

;Not-aus-Sequenz
M112			;Not-Aus, Sofortiger Stop
M999			;software Neustart 

Maybe i am wrong with my Setup.