Duet3D Logo

    Duet3D

    • Register
    • Login
    • Search
    • Categories
    • Tags
    • Documentation
    • Order
    1. Home
    2. falcar
    • Profile
    • Following 0
    • Followers 0
    • Topics 8
    • Posts 26
    • Best 0
    • Controversial 0
    • Groups 0

    falcar

    @falcar

    0
    Reputation
    1
    Profile views
    26
    Posts
    0
    Followers
    0
    Following
    Joined Last Online

    falcar Unfollow Follow

    Latest posts made by falcar

    • Paneldue - Filaments

      Do you guys know if there is a way to add the filaments unload/load/change on the Paneldue?

      I have to use my phone to do this but would love a way to do it right on the panel.

      posted in PanelDue
      falcar
      falcar
    • RE: Gcode controlled fan

      Yes i can move the slider to 100%

      I'm in the middle of a print right now, but i'll try that when its done.

      The main reason is the fan is quite a bit louder at 95% than 100%

      posted in General Discussion
      falcar
      falcar
    • RE: Gcode controlled fan

      Sure,

      ; Fans
      M106 P0 S0.3 I0 F500 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
      M106 P1 S1 I0 F500 H1 T45 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on

      posted in General Discussion
      falcar
      falcar
    • Gcode controlled fan

      For some reason even if I set my cooling to 100% in the slicer, it only sets it to 95%

      Any idea how i can get it to respect the slicer setting?

      posted in General Discussion
      falcar
      falcar
    • RE: Short to ground on driver 3

      Rewiring seems to have solved the issue. For safety sake I think I will also remove stealthchop.

      Thanks guys!

      Any idea a good source to purchase more of them connector ends? I used all of the ones that came with my wifi on my maestro!

      posted in General Discussion
      falcar
      falcar
    • RE: Short to ground on driver 3

      The wire isn't very long. It's one I purchased off of Amazon. I will check to make sure there are no wires loose or shorting.

      I'll also try the other mode too if I don't find anything.

      If I discover the problem will this error have caused any irreparable damages ?

      posted in General Discussion
      falcar
      falcar
    • RE: Short to ground on driver 3

      In my config.g:

      M569 P3 S1 ; Drive 3 goes forwards

      Command run:

      2:31:16 PMM569 P3
      Drive 3 runs forwards, active low enable, step timing fast, mode stealthChop, ccr 0x00053, toff 3, tblank 0, hstart/hend/hdec 5/0/0, tpwmthrs 2000 (1.0 mm/sec)

      posted in General Discussion
      falcar
      falcar
    • RE: Short to ground on driver 3

      Yes I'm on 2.02. This is the first time I've seen it. Which driver is 3?

      posted in General Discussion
      falcar
      falcar
    • RE: Short to ground on driver 3

      A maestro. No I haven't done anything like that

      posted in General Discussion
      falcar
      falcar
    • Short to ground on driver 3

      Good morning all

      My printer has been working great for at least a month. About 9 hours into a print it threw this error a few times in the logs. Any ideas on what could have happened? What should I look at?

      posted in General Discussion
      falcar
      falcar