Hello everybody,
after send the code for the dsf log this said that trigger6 do the restart...

I checked trigger6 and my config.g and is truth... i did a mistake in the config.g file...

Sorry for that, i was desperate!!

Thanks for your support!

After test a lot time i can say that with "crimped bootlace ferrules" everything is ok.

Thanks a lot!

@gloomyandy I mean turn on/off the output relay

@timschneider thank you!!! now work properly!!

Hello,
I use Duet2 with the latest firmware 3.1.1.
I use a filament runout sensor which is basically a switch.

https://reprapworld.es/products/extruder/extruder_parts/filament_detection/filament_run_out_sensor_1_75mm/

The problem is that when there is filament the switch is pushed and the sensor is on (Led on on the board), if at any time during the printing there is any interference or the diameter is smaller than normal, the sensor is not pushed and the printer pauses and indicates no filament
I think it is usually interference of maybe a few milliseconds, but enough to stop the printer.

My idea is:
When the duet reads the sensor OFF for at least 5 seconds (or 2), the duet reports NO Filament.

I don't know if it is possible to configure this, or maybe with MetaCommands it is possible. I do not think so.

Someone understands me?

@gloomyandy I mean turn on/off the output relay

@timschneider thank you!!! now work properly!!

Re: How to make a loop of a Output_Pin ON and OFF?

Sorry for late response...

If i try the code (inside daemon.g):

while state.status  != "printing"
    M42 P1 S1
    G4 S2
    M42 P1 S0
    G4 S10

Works properly as the code said.

But i want that works while i am printing so... i use:

while state.status  != "idle"
    M42 P1 S1
    G4 S2
    M42 P1 S0
    G4 S10

If I start printing a file, it seems that the Duet3 6HC can't do two things at the same time... The duet can't make any movement and while it does it it loops.
Activates or deactivates the port sometimes during line changes.

It's like not having multitasking... one task to make the loop and another task to make movements...

Surely it can be done, but I don't know how...

Thank you!

Hello everybody!
I have very clear how to control a heated bed with a SSR, simple use the output in mode PID and not more...

But with big heated bed is better use a 4-20ma SSR because modulate the voltage...

Someone have idea how the duet3 can mange a output pin with 4-20ma?

If signal 4-20ma is not possible....0-10V modulated?
Best Regards

Hello everybody,
after send the code for the dsf log this said that trigger6 do the restart...

I checked trigger6 and my config.g and is truth... i did a mistake in the config.g file...

Sorry for that, i was desperate!!

Thanks for your support!

@dc42 Where i can find DSF logs?

Hello,

i use duet 6XD some days and everything was ok, but now while i am printing or not, the board show me the message for restart...

Emergency stop, attemping to reconnect...

I don't know why, i dont have any input config that restart the board for any alarm or similar.

This is the M122 that give me after restart.

Any idea?

M122
=== Diagnostics ===
RepRapFirmware for Duet 3 MB6XD version 3.4.5 (2022-11-30 19:41:59) running on Duet 3 MB6XD v1.0 or later (SBC mode)
Used output buffers: 1 of 40 (12 max)
=== RTOS ===
Static ram: 151200
Dynamic ram: 65076 of which 0 recycled
Never used RAM 134396, free system stack 219 words
Tasks: SBC(ready,0.5%,511) HEAT(notifyWait,0.0%,374) Move(notifyWait,0.0%,351) CanReceiv(notifyWait,0.0%,944) CanSender(notifyWait,0.0%,336) CanClock(delaying,0.0%,343) MAIN(running,96.9%,1232) IDLE(ready,2.6%,29), total 100.0%
Owned mutexes: HTTP(MAIN)
=== Platform ===
Last reset 00:00:32 ago, cause: software
Last software reset at 2023-05-04 14:57, reason: User, none spinning, available RAM 130916, slot 1
Software reset code 0x0012 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00400000 BFAR 0x00000000 SP 0x00000000 Task SBC Freestk 0 n/a
Error status: 0x00
Step timer max interval 18465
MCU temperature: min 36.8, current 37.0, max 47.2
Supply voltage: min 24.0, current 24.1, max 24.1, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.1, current 12.1, max 12.2, under voltage events: 0
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Events: 0 queued, 0 completed
Driver 0: ok
Driver 1: ok
Driver 2: ok
Driver 3: ok
Driver 4: ok
Driver 5: ok
Date/time: 2023-05-04 14:58:31
Slowest loop: 25.43ms; fastest: 0.04ms
=== Storage ===
Free file entries: 10
SD card 0 not detected, interface speed: 37.5MBytes/sec
SD card longest read time 0.0ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 125, segments created 0, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP* is doing "M122" in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger* is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty
=== CAN ===
Messages queued 165, received 0, lost 0, boc 0
Longest wait 0ms for reply type 0, peak Tx sync delay 0, free buffers 50 (min 50), ts 165/0/0
Tx timeouts 0,0,164,0,0,0 last cancelled message type 30 dest 127
=== SBC interface ===
Transfer state: 5, failed transfers: 0, checksum errors: 0
RX/TX seq numbers: 1616/1616
SPI underruns 0, overruns 0
State: 5, disconnects: 0, timeouts: 0 total, 0 by SBC, IAP RAM available 0x2b770
Buffer RX/TX: 0/0-0, open files: 0
=== Duet Control Server ===
Duet Control Server v3.4.5
Code buffer space: 4096
Configured SPI speed: 8000000Hz, TfrRdy pin glitches: 13
Full transfers per second: 51.67, max time between full transfers: 257.0ms, max pin wait times: 36.0ms/10.0ms
Codes per second: 1.98
Maximum length of RX/TX data transfers: 3008/844

Sorry dears, not solved.
I was thinking that is working because don't show error but now say:

Error: Failed to read code from macro daemon.g: empty while loop detected in line 2

My code is:

while state.status  != "idle"
M42 P5 S1
G4 S2
M42 P5 S0
G4 S10

Thanks a lot!

Now is working properly!!

@T3P3Tony Tested in 3.4.5 yes.

Whats do you mean with "have the events setup"?
sorry...

@jay_s_uk I try but....
Error: Failed to read code from macro daemon.g: Failed to evaluate "state.status <> idle": expected an expression

This is my daemon file:

while state.status <> idle
M42 P5 S1
G4 S2
M42 P5 S0
G4 S10