@gabit Thanks, now it works!

i removed the ethernet-platine, now the green 3.3 V led light and i have 3 Volt at pin 3
the ethernet platin looks well good

@phaedrux What are the next steps, i need my duet and wait for resulation.
I think the board is damaged.

@phaedrux
Hi,

• with removed SD Card it gets also hot in a view seconds.
• because of this, i think the config.g is not the problem
• the Board is changed on 4.Jan see here
• since it is changed it runs perfect, until a view days ago, nothing changed at this time
• it it purchased at 19.04.2021 by filafarm (berlin/germany)
• the z drive is never used, no stop no stepper
• then new firmware i installed after i have get this problems, before it was workbee controll 1.0

M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.2.2 running on Duet Ethernet 1.02 or later
Board ID: 0JD0M-9P6B2-NJ4S8-6JKF0-3SD6Q-TU7UL
Used output buffers: 1 of 24 (10 max)
=== RTOS ===
Static ram: 23460
Dynamic ram: 69040 of which 60 recycled
Never used RAM 19520, free system stack 204 words
Tasks: NETWORK(ready,206) HEAT(blocked,212) MAIN(running,471) IDLE(ready,20)
Owned mutexes:
=== Platform ===
Last reset 00:02:31 ago, cause: power up
Last software reset at 2022-03-27 16:00, reason: User, GCodes spinning, available RAM 19520, slot 1
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00000000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Aux0 errors 0,0,0
MCU temperature: min 31.1, current 35.6, max 116.7
Supply voltage: min 1.3, current 1.7, max 2.1, under voltage events: 0, over voltage events: 0, power good: no
Driver 0: position 0, ok, SG min/max not available
Driver 1: position 0, ok, SG min/max not available
Driver 2: position 0, ok, SG min/max not available
Driver 3: position 0, ok, SG min/max not available
Driver 4: position 0, ok, SG min/max not available
Driver 5: position 0
Driver 6: position 0
Driver 7: position 0
Driver 8: position 0
Driver 9: position 0
Driver 10: position 0
Driver 11: position 0
Date/time: 2022-03-31 19:05:18
Cache data hit count 290514072
Slowest loop: 7.05ms; fastest: 0.20ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 3.7ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 7.03ms; fastest: 0.01ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8
Interface state active, link 100Mbps full duplex

Hi
i got some errors on drive 2
All is clean, nothing is on board which could create short
The Chip is getting hot
Even if nothing is connected to the boad and powered by usb

@gabit Thanks, now it works!

@jay_s_uk ok thanks, i try this

@jay_s_uk Is this DWC?

@jay_s_uk ok, i knew this page and my code is from this side
the only different is the connector

; New code
M950 R0 C"!exp.heater3" L12000 ; Create spindle index 0, with PWM pin on heater 3 and 12000 RPM achieved at full PWM
M563 P1 S"Spindle 1" R0 ; Create tool 1 with spindle 0 and call it "Spindle 1"
M453

Doesnt work, same error

; Old code
M453 S0 T1 C"!exp.heater3" R12000 ; Assign tool 1 to spindle index 0, with PWM pin on heater 3 and 12000 RPM achieved at full PWM

The same, what is the problem?

Hi,
i try to make a spindle Controll via Duet 2 Wlan

M115
FIRMWARE_NAME: RepRapFirmware for Duet 2 WiFi/Ethernet FIRMWARE_VERSION: 3.3 ELECTRONICS: Duet WiFi 1.02 or later FIRMWARE_DATE: 2021-06-15 21:45:03

my prefered config.g is like

M950 R0 C"!e1heat" L22000     ; Create spindle index 0, with PWM pin on heater 1 and 22000 RPM achieved at full PWM
M563 P1 S"Spindle 1" R0       ; Create tool 1 with spindle 0 and call it "Spindle 1"
M453                          ; CNC Mode

when i start with this config or send manual this "M950 R0 C"!e1heat" L22000 " i got

What is the correct Code for define a spindle in RepRap 3.3

@alankilian all looks fine, i have the same resistance between gnd and 3,3 volt.
Is it possible to get a new one, i have network connection problems since i got the duet

i removed the ethernet-platine, now the green 3.3 V led light and i have 3 Volt at pin 3
the ethernet platin looks well good