@dc42 Thanks for the info about the polarity. That now makes sense! I bought some PMV20XNER MOSFETs, but the size of them is way beyond my capability.
I tried to PM you, but I get then message "This user has restricted their chat messages. They must follow you before you can chat with them"
@bearer Thanks I will check as I have now visually blown P3. Also P1 stopped working. So all 3 now not working! Is there anywhere in the UK that I can send the board to get it fixed?
(I bought pre-wired connectors, but I didn't see that although the connectors were compatible at the hot end the polarity was reversed to the fan. I wouldn't have thought that switching the fan polarity would have blown anything - the fans would just spin the wrong way).
@Phaedrux Hope it's clear enough.
Getting:
Error
Input file contains unsupported image format
@Phaedrux Yeah. Nothing physically obvious. What also confused me was the 2 Fans on the WebGUI. I didn't notice that one was Tool Fan and the other Fan 0, which are the same. I thought one was the heatsink fan, which thinking about it now wouldn't make sense as it's not speed controllable. Thanks for your help.
@Phaedrux Tried the following:
fan0 Molex into fan2 header
config.g changes
;Fans
; M106 P0 S0 I0 F500 H-1 ; Disable FAN0: Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P2 S0 I0 F500 H-1 ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned off
;Tools for p0
; M563 P0 D0 H1 F0
M563 P0 D0 H1 F2
It seems to work!
@Phaedrux I've taken molex off fan header connections and attached direct to 24v. All fans/wiring okay. My mistake about speed - it's just a quiet - ish fan.
That's maybe something if m106 and the sliders have no effect?
send M106 P1 H-1 and heatsink fan comes on. No change to WebGUI controls
M106 P1 S0 fan stops (WebGUI speed sliders - no effect)
M106 P1 S1 fan on (WebGUI speed sliders - no effect)
M106 P0 S1 no change to part cooling fan - still off
@Phaedrux MOSFETs look okay. Do you know if the WebGUI fan speed slider issues the M106 command?
@Phaedrux M563 P0 D0 H1 Same as my other machine which works and dozuki says you can omit for tool0. Added F0 and rebooted - no change. M106 P0 S1 does not turn the fan on. Vin jumper selected as in working machine. I cannot figure it out. Thanks for trying to help. Strange that heatsink fan starts when over 45C, but WebGUI hs no effect on it either below or above 45C.
I'm still commissioning the machine, so most of the config is from my other machine. Main problem is that the WebGUI fan speed sliders have no effect (also M106 no effect). Hotend fan kicks in at 45C. Fan seems slow, but it's hard to tell. (firmware 2.05.1)
; Configuration file for Duet WiFi (firmware version 1.21)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2 on Tue Feb 26 2019 21:31:01 GMT+0000 (Greenwich Mean Time)
;made by Gary 22/07/2020
; General preferences
G21 ; Work in millimetres
G90 ; Send absolute coordinates...
M83 ; ...but relative extruder moves
M552 S1 ; connect to WiFi
; Delta Settings
M665 L440.49 R227 H456.747 B185.0 ; Set delta radius, diagonal rod length, printable radius and homed height
M666 X0 Y0 Z0 A0.00 B0.00 ; Put your endstop adjustments here, or let auto calibration find them
; Network
M550 P"P1" ; Set machine name
M551 P""
M552 P192.168.0.16 ; Set password
;M552 P0.0.0.0 S1 ; Enable network and acquire dynamic address via DHCP
M586 P0 S1 ; Enable HTTP
M586 P1 S0 ; Disable FTP
M586 P2 S0 ; Disable Telnet
; Drives
M569 P0 S0 ; Drive 0 goes forwards
M569 P1 S0 ; Drive 1 goes forwards
M569 P2 S0 ; Drive 2 goes forwards
M569 P3 S0 ; Drive 3 goes forwards (BMG extruder clone - MT-1703HSM168RE 0.9deg step 180917 1.68A)
M350 X16 Y16 Z16 E16 I1 ; Configure microstepping with interpolation (20teeth pulley) "E3D MT-1704HSM168RE 0.9deg step 190102, 400 steps/rev 1.68A"
M92 X160.00 Y160.00 Z160.00 E837 ; Set steps per mm
M566 X1000 Y1000 Z1000 E1000 ; Set maximum instantaneous speed changes (mm/min)
M203 X12000.00 Y12000.00 Z12000.00 E10000 ; Set maximum speeds (mm/min)
M201 X3000.00 Y3000.00 Z3000.00 E3000.00 ; Set accelerations (mm/s^2)
M906 X1000.00 Y1000.00 Z1000.00 E1100.00 I30 ; Set motor currents (mA) and motor idle factor in per cent
;M906 X1344.00 Y1344.00 Z1344.00 E1344.00 I30 ; Set motor currents (mA) and motor idle factor in per cent (reduced to 80% of max Amps)
;M84 S30 ; Set idle timeout
M84 S600
; Retraction
M207 S4.0 F5000 R-0.025 T2500 Z0.5 ; Firmware retraction
; Axis Limits
M208 Z0 S1 ; Set minimum Z
; Endstops
M574 X2 Y2 Z2 S1 ; Set active high endstops
; Z-Probe (standard AC Predator microswitch probe, clips just under nozzle)
M558 P4 H25 F120 T6000 ; Set Z probe type to switch(P4) and the dive height + speeds
G31 P500 X0 Y0 z17.225 ;Z22.446 ;17.249 ;.656 ; Set Z probe trigger value, offset and trigger height
M557 R115 S20
;G29 S1 ; Load the heightmap
; Heaters
M307 H0 A137.8 C533.3 D1.5 V24.3 B0 ; Disable bang-bang mode for the bed heater and set PWM limit
M305 P0 T100000 B4300 C0 R4700 ; Set thermistor + ADC parameters for heater 0
M143 H0 S120 ; Set temperature limit for heater 0 to 120C
M305 P1 T100000 B4300 C0 R4700 ; Set thermistor + ADC parameters for heater 1
M143 H1 S240 ; Set temperature limit for heater 1 to 240C
; Fans
M106 P0 S0 I0 F500 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H1 T45 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
; Tools for p0
M563 P0 D0 H1 ; Define tool 0
G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets
G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C
; Automatic saving after power loss is not enabled
; Custom settings are not configured
M572 D0 S0.1 ; Pressure Advance
;M591 D0 P2 C4 S1 ; Activate filament sensor
M404 N1.75 ; Set for print monitor
M592 D0 A0.07772 B-0.00029 ; Nonlinear extrusion. Set parameters for extruder drive 0
; Miscellaneous
T0 ;select tool 0 gary added
M501 ; Load saved parameters from non-volatile memory
Just remembered that the fan speed sliders never worked, which is why I thought something was wrong. Hotend fan still working. I think there was something wrong before I blew the fuse as above.
Sorry my names for the printers Predator1 and 2. Predator1, Predator1, is the problem printer. (edited above to remove references to P1 and changed to Predator1)
I have a Duet 2 Wifi in an existing printer, Predator2. Just installed a Duet 2 Wfi in another printer, Predator1. Both printers are the same deltas apart from fan makes, but all 4020s.
Predator2 working. Dozuki instructions on fans very confusing, so copied everything from Predator2.
duet 2 wifi
V2.05.01
2 wire fans (common + ve on all fans from heatsink fan header)
2x24v part cooling parallel
1x24v heatsink fan
Problem: Predator1 does not respond to webGUI fan sliders.
boot up - heatsink fan spins briefly
try web GUI sliders when cold - nothing
over 45C heatsink fan spins (although seems well under full speed) - use sliders no speed variance - part cooling nothing
web GUI no change using sliders on any fan
After messing with above:
(- ve on part cooling wire maybe loose - did have them on at one point though)
did blow fuse with part cooling FAN0 on trying to check voltage - something else blown?
M106 into GUI - no effect
config.g
M106 P0 S0 I0 F500 H-1
M106 P1 S1 I0 F500 H1 T45
Any ideas or help welcome.
Regards
Gary
Hi, Sorted at some point the X belt had twisted with the non-toothed side running on the stepper. I didn’t even notice when checking the stepper grub screws. I couldn’t see the belt twist as it’s slightly recessed on the machine, but I noticed when looking closely at the carriage and tabs. Really noticeable when you manually move the carriage up and down. It makes sense now as when I did a HomeDelta quite often, but not all the time, the interface would report not all axis homed and they weren’t. I just thought it was an annoying “feature” that would sometimes happen and I would have to click Home again. The board was turning the stepper the 490mm distance I have in my HomeDelta and not triggering the end stop giving the error. Also when doing probing from high up the results were inconsistent – belt slippage. Down low with slow probes it was okay. After a Home the X and Y values were not zero on the interface and when touching bed the hot end was not centred on the bed. Now to change the belts and somehow fix the bed which got smashed at the edge when the Perspex lid hit it!
M665 L440.000:440.000:440.000 R226.630 H455.788 B185.0 X0.093 Y0.750 Z0.000
M666 X-0.012 Y-0.045 Z0.057 A0.00 B0.00
Updated, checked all endstops/tabs and they all look okay. Similar distances and wiring the same. Just done another probe and config override as below.
M665 L440.000:440.000:440.000 R227.000 H456.747 B185.0 X0.000 Y0.000 Z0.000
M666 X0.000 Y0.000 Z0.000 A0.00 B0.00
That can't be right all zeros. I did notice that the first probe was not in the center of the bed - 10ish mm out.
@jay_s_uk
Sorry I meant initial hot end paper touch before using probe. z=0 at this height.
@jay_s_uk
Will update the firmware. It was just a thought as X-6.790 and my probe offset of 5.52 gives 1.27mm which would correlate roughly to what I felt with my finger maybe.
@jay_s_uk
I got the error " Warning: the height map was loaded when the current Z=0 datum was not determined probing. This may result in a height offset." Just wondered if the problem could be anything like the link below?
https://forum.duet3d.com/topic/10835/z-0-datum-was-not-determined-probing/3
I can kind of see that having both a Z endstop switch and a Z probe could cause a problem, as the z tower is not the z height.
Mine Firmware is: RepRapFirmware for Duet 2 WiFi/Ethernet 2.04 (2019-11-01b1)
Have you got the same firmware version?
@jay_s_uk
Yes. Got my finger under all of them and one is maybe a 0.5/1mm higher, not 10. Disassembly required. Never seen an endstop could it be upside down?
@jay_s_uk
The flags look/feel the same as my other stock machine. I'll need to get to the endstops as that's a huge difference.
Just done another re-probe and similar results.
M665 L440.000:440.000:440.000 R224.513 H456.388 B185.0 X-0.646 Y-0.364 Z0.000
M666 X-6.930 Y3.322 Z3.607 A0.00 B0.00
