Posts made by HenryDara

Finally it did upgrade one of my machines to the new DWC, I think only when I did a full install rather than just the DWC. Not sure, it was real late.

Kind of related to what @Danal was saying, I had another problem with uploading a full set of configuration files. Heres what I did...

Selected all files in configuration, including pause.g, etc Heres a shot of the folder after it downloaded showing all the files...

Then I uploaded those files to a different configuration folder the normal way using the "Upload system files" button, then selecting the download.zip. After it was done it reported 29 files downloaded, and the folder shows the new dates on the files, so it looks ok.

But when I really look only 14 files made the trip, so no pause.G, etc. Which by the way causes some very strange behavior on the printer when they are not there

I can get past this by just pulling the SD card, but it seemed worth sharing, and to get any thought about errors on my part.

Thanks again...HD

@jay_s_uk Thanks, I was trying to avoid the SD thing cause I have a dozen of these to do. I was hoping I was just missing something obvious in the way I was doing it.

Upload used to be in the Settings/General tab, but now I think its under FIle management/System, which has me wondering how it works when using multiple configurations, which I am doing at the moment. I wouldnt think it would matter, but maybe it does. All of my printers use multiple configurations in sub folders, and none of them will update the DWC after uploading the files.

Actually I have no idea what version I have these days. It says 2.0.4, but then theres DWC 1, and its all just a bit confusing whats what these days. I hope someone comes up with a chart to make it easy some day.

Either way, I spoke to soon when I said it worked, it didnt. it reloads DWC after uploading, but the version never changes from 2.0.4.

This completes, but no update.

Never mind, it works when I revert back to DWC1. I guess it wasnt part of the last release. Not sure.

Whats the new secret for uploading DWC to Duet wifi using DWC?

Usually I just click upload, and it uploads, then installs, but now it just uploads but does not install. Tried using Chrome, Firefox, IE, but neither seem to work.

IS there a new procedure for this?

Thanks...HD

Trying to understand what is what here.... 2.0.7 that came in the last release (3.01-RC5) is the same as 2.0.7 from before? (No change?)

Should we expect anything to be fixed in the latest 2.0.7?

Should we not expect fixes until 2.1.0 is released?

I have been hoping for this one to get fixed for a while...thanks

https://forum.duet3d.com/topic/14743/heater-numbers-incorrect-in-dwc-2-0-7

What are your Z screws setting on? It looks to me like inconsistencies in your Z axis causing a lean of the whole part. It looks like it gets worse as the part gets taller. I had similar problems when my Z screws were coupled directly to the stepper shafts, which had endplay, and inconsistent springiness that could not be controlled. As one screw advanced less than the other, the bed tilted and the part leaned just a bit causing a very similar affect. I think it happened lower in the print as well, but the error was amplified as the part got taller, and seemed to gradually appear rather than start late in the print.
Do your screws rest in a bearing meant for thrust load? It looks pretty good from the pics, but I cant tell whats at the bottom end of the screw.
(Mine ended up on pin roller thrust bearings, but my beds get to weigh 40-50 lbs empty)

@Phaedrux Thanks for the update. Yes cosmetic, but causing us to make mistakes when setting individual nozzle temperatures. We adjust the numbers in our head for now, so I hope we can untrain when the numbers are correct on DWC2. Any idea how long before DWC2 gets released?

Thanks...HD

If I knew HTML I would dig to find out why it displays the wrong numbers. I dont see anything in the config that might cause a discrepancy on the main HTML page, it it makes no sense that the numbers would be correct in one pane, while different in the one right next to it. Everything functions correctly when I run all six nozzles, so its not the end of the world, but would like to figure it out someday.

@aego Also you should be using 192.168.0.55 for your browser address (or 192.168.0.55/reprap.htm to use DWC1)

@aego try forgetting the network with

M588 S"dlink-3DC4"

then adding it back to the list with

M587 S"dlink-3DC4" P"<wifi password>"
(replace with your actual password)

Connect Duet to wifi (if it doesnt automatically)
M552 S1

then check it with M587 again

Not sure why but when mine has gotten hosed up in the past this is how I recovered.

@aidar Ahhh yes, very good catch. Fixed it in the Config, but that didnt fix the number issue. Thanks for the heads up.

@dc42 Do you have any thoughts on this issue? Thanks...Henry

Sounds like the IP changed on ya. Use YAT and send M587 (no para) to list net info...

Is the blue WIFI light on solid? If so, it is connected to your Wifi, and you just need to know the IP address.

If not these may help...

To set the network...
M587 S"SSID" P"password"

To forget the network
M588 S"SSID"

Also
M552 S0 = Disconnect Wifi
M552 S1 = Connect Wifi

@chrishamm Do you have any thoughts on this?

@Phaedrux Tried that too, but still the same result. Thanks

@Phaedrux Gave that a try, but it just did the same thing with the new custom text.

Still a problem in DWC 2.0.7 with heater numbers in the tool list.

Trend chart is correct, but tool list shows heater 1 twice, and omits the last heater regardless the number of heaters

I have another machine with 4 printheads that does the same thing at DWC rev 2.0.4

This problem only happens when combining multiple heaters/drives on one tool, but not when I configure them independently.

Board: Duet WiFi 1.02 or later + DueX5
Firmware: RepRapFirmware for Duet 2 WiFi/Ethernet 2.05.1 (2020-02-09b1)

Config:
; Configuration file for Duet WiFi (firmware version 1.21)
; executed by the firmware on start-up
;
; By Versatile 3D LLC 8/13/2019

; General preferences

G90 ; Send absolute coordinates...
M83 ; ...but relative extruder moves
M200 D1.75 ; set all extruder filament diameters to 1.75mm
M667 S1 ; Select CoreXY mode

; Z-Probe
M307 H6 A-1 C-1 D-1 ; Disable the 6th Heater to free up PWM channel 4 on the Duex board. (Special Parameters to chg PWM ch to discreet)
M307 H7 A-1 C-1 D-1 ; Disable the 7th Heater to free up PWM channel 5 on the Duex board. (Special Parameters to chg PWM ch to discreet)
M558 P5 H5 F50 T1500 X0 Y0 Z1 ; Set Z probe type/mode 5. H=Dive Height. F=Speed the bed moves T=Travel Speed(From https://betrue3d.dk/bltouch-on-duet-wifi-configuratio-and-usage/#wiring)
G31 P100 X0 Y30 Z1.50 ;(Z - larger number = smaller gap) Set Z probe trigger value, offset and trigger height
;G29 S1 ; Enable Mesh Bed Compensation (S1 = Load Prev Grid, S0 = New grid probe on pwr up))
M557 X60:600 Y10:425 S75 ; Define mesh grid for printing compensation
M376 H10 ; Set Mesh Bed Taper Height.

; External IO
M581 E6 S0 T0 C0 ; Configure E-Stop as E5(E6) S0(NC) T0(Trigger EStop) C0 (Anytime)

; Network
M550 P"Printfarm-PRO Model 584 PH-1,2,3,4,5,6" ; Set machine name
M551 P"V3DLLC: ; Set password
M552 S1 ; Enable network
;*** Access point is configured manually via M587
M586 P0 S1 ; Enable HTTP
M586 P1 S0 ; Disable FTP
M586 P2 S0 ; Disable Telnet

; Drive Directions
M569 P0 S0 ; XY Front / Drive 0 goes backwards
M569 P1 S1 ; XY Rear / Drive 1 goes forwards
M569 P2 S1 ; Z-Left Screw / Drive 2 goes forwards
M569 P3 S1 ; Extruder 0 / Drive 3 goes forwards
M569 P4 S1 ; Extruder 1 / Drive 4 goes forwards
M569 P5 S1 ; Extruder 2 / Drive 5 goes forwards
M569 P6 S1 ; Extruder 3 / Drive 6 goes forwards
M569 P7 S1 ; Extruder 4 / Drive 7 goes forwards
M569 P8 S1 ; Z-Right Rear Screw / Drive 8 goes forwards
M569 P9 S1 ; Z-Right Front Screw / Drive 9 goes forwards

; Drive Scaling
M350 X16 Y16 Z16 E16 I1 ; Configure microstepping with interpolation
M92 X160.00 Y160.00 Z2535.00 E2660 ; Set steps per mm

M566 X15 Y15 Z.25 E20 ; Set maximum instantaneous speed changes (mm/min)
M201 X800.00 Y1000.00 Z25.00 E1500.00 ; Set accelerations (mm/s^2)
M203 X15000.00 Y15000.00 Z1200.00 E5000.00 ; Set maximum speeds (mm/min)
M204 R1000 ; Set Retract accelerations
M205 E3 ; Set Extruder Jerk (not sure where I found this)
M906 X1000.00 Y1000.00 Z800.00 E600.00 I30 ; Set motor currents(mA) and motor idle factor in percent
M84 S30 ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1 ; Set axis minima
M208 X450 Y600 Z370 S0 ; Set axis maxima

; Drive/Axis Setup
M584 X1 Y0 Z2:8:9 E3:4:5:6:7 ; Drive Mapping (XY=drvs 0/1, Z screws=drvs 2/8/9, extruders=drvs 3/7)
M671 X1:610:610 S3 Y340:705:28 ; Set XY offsets for Z screws at

; Endstops
M574 X1 Y1 S1 ; Set active high endstops for X and Y axis
M574 Z1 S2 ; Set endstops controlled by probe (disabled for commissioning W/O Z probe)

; Heaters
;BED HEATER
M307 H0 B0 S1.00 ; Disable bang-bang mode for the bed heater and set PWM limit
M305 P0 T100000 B4138 R4700 ; Set thermistor + ADC parameters for bed heater 0
M143 H0 S120 ; Set temperature limit for heater 0 to 120C

;TOOL HEATERS
M305 P1 B4725 C7.060000e-8 ; Set thermistor + ADC parameters for heater 1
M307 H1 A35 C135 D3.75 B0 ; Set heater tuning parameters for heater 1 (E3D V6 XX Watt Htr Cartridge)
M143 H1 S280 ; Set temperature limit for heater 1 to 280C
M305 P2 B4725 C7.060000e-8 ; Set thermistor + ADC parameters for heater 2
M307 H2 A35 C135 D3.75 B0 ; Set heater tuning parameters for heater 2 (E3D V6 XX Watt Htr Cartridge)
M143 H2 S280 ; Set temperature limit for heater 2 to 280C
M305 P3 B4725 C7.060000e-8 ; Set thermistor + ADC parameters for heater 3
M307 H3 A35 C135 D3.75 B0 ; Set heater tuning parameters for heater 3 (E3D V6 XX Watt Htr Cartridge)
M143 H3 S280 ; Set temperature limit for heater 3 to 280C
M305 P4 B4725 C7.060000e-8 ; Set thermistor + ADC parameters for heater 4
M307 H4 A35 C135 D3.75 B0 ; Set heater tuning parameters for heater 4 (E3D V6 XX Watt Htr Cartridge)
M143 H4 S280
M305 P5 B4725 C7.060000e-8 ; Set thermistor + ADC parameters for heater 5
M307 H5 A35 C135 D3.75 B0 ; Set heater tuning parameters for heater 5 (E3D V6 XX Watt Htr Cartridge)
M143 H5 S280
M305 P6 B4725 C7.060000e-8 ; Set thermistor + ADC parameters for heater 6
M307 H6 A35 C135 D3.75 B0 ; Set heater tuning parameters for heater 6 (E3D V6 XX Watt Htr Cartridge)
M143 H6 S280

; Fans
M106 P0 S0.3 I0 F500 H-1 ; Set Fan 0 P0 (Fan 0), S0.3 (30%), I0 (default), F500 (PWM 500hz), H1 (Disable Thermostatic Mode)
M106 P1 S0.3 I0 F500 H-1 ; Set Fan 1 P1 (Fan 1), S0.3 (30%), I0 (default), F500 (PWM 500hz), H1 (Disable Thermostatic Mode)
M106 P2 S1 I0 F500 H1 T45 C"Box_Fan" ; Duet Enclosure Cooling Fan

; Tools
;Clone Mode*******
M563 P0 S"Six Head Tandem Mode" D0:1:2:3:4 H1:2:3:4:5:6 F0:0:1 ;Tool setup
G10 P0 S0 R0 X30 Y0 ; Set tool 0 temperatures and offsets (S0/R0=Standby/Active Temp.)
M567 P0 E1.0:1.0:1.0:1.0:1.0 ;Set Extruder Drive Ratios (all drives at 1.0 for ditto printing, add ":1.0" for each tool in use)
M568 P0 S1 ;enable mixing ratios

;Single/Dual Extrusion Modes*******
;M563 P0 S"RT Tool" D1 H2 ; Std Printing - Define tool 0
;G10 P0 S0 R0 X30 Y0 ; Set tool 0 temperatures and offsets (S0/R0=Standby/Active Temp.)
;M563 P1 S"LT Tool" D0 H1 ; Std Printing - Define tool 1
;G10 P1 S0 R0 X-35 Y0 ; Set tool 1 temperatures and offsets

;M572 D0 S0.05 ; Set Pressure Advance for Extruder 1
;M572 D1 S0.05 ; Set Pressure Advance for Extruder 2

; Automatic power saving
;M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; Set voltage thresholds and actions to run on power loss

; Custom settings are not configured

; Simulated print time: 0