Posts made by Honey_Badger357

@droftarts instructions are unclear which files are required to be downloaded and where they need to be located on the PC. Attached is a picture of the files the link brought me to down load but neither file started to download a driver. Also, in device manager no devices have a yellow triangle and the “generic USB” didn’t have a driver to download

can you walk me through using YAT please?

; Fusion3 F410 Firmware configuration file
; For FusionWare 1.18.1 RC2
; Revision 2019.06.27
; For Serial Number 6739

M111 S0 ; Debug off
M550 PFusion3 F410 ; Machine name MUST HAVE A "P" IN FRONT OF IT(can be anything you like)
M551 Pfusion3 ; Machine password MUST HAVE A "P" IN FRONT OF IT
M540 P0xBE:0xEF:0xDE:0xAD:0x67:0x39 ; MAC Address (replace last 2 blocks with 4 digit s/n)
;=== Adjust the following 3 lines to suit your network ===
M552 P0.0.0.0 S1 ; IP address (0 = use DHCP)
M554 P192.168.1.1 ; Gateway
M553 P255.255.255.0 ; Netmask
;=========================================================
M555 P2 ; Set output to look like Marlin
M575 P1 B57600 S1 ; comms params for paneldue

; Machine configuration
M569 P0 S1 ; Drive 0 goes forwards
M569 P1 S0 ; Drive 1 goes backwards
M569 P2 S0 ; Drive 2 goes backwards
M569 P3 S0 ; Drive 3 goes backwards
M569 P4 S0 ; Drive 4 goes backwards
M574 X1 Y1 Z2 S1 ; set endstop configuration
M667 S1 ; set CoreXY mode
M92 X44.00 Y44.00 Z426.67 E190.0 ; set axis steps/mm
M906 X1300 Y1300 Z1400 E1400 I100 ; Set motor currents (mA)
M201 X2000 Y2000 Z300 E4000 ; Accelerations (mm/s^2)
M203 X33000 Y33000 Z2500 E10000 ; Maximum speeds (mm/min)
M566 X600 Y600 Z40 E950 ; Maximum jerk speeds mm/minute
M208 X355 Y355 Z315 ; set axis maxima
M208 X0 Y0 Z0 S1 ; set axis minima
G21 ; work in mm
G90 ; absolute coords
M83 ; relative extruder movements

; Z probe
M558 P5 X0 Y0 Z0 H7 F100 ; Set probe type and if it's used for axis homing (no in our case)
G31 Z-0.05 P600 ; Set the probe height and threshold (smaller number = further away from bed)

; Thermistors and heaters
M305 P0 T100000 B4036 R4700 ; Bed thermistor
M305 P1 T100000 B4725 C7.06e-8 R4700 ; Head thermistor
;M305 P2 T100000 B4725 C7.06e-8 R4700 ; Not needed

M307 H0 A153.5 C534.2 D6.7 B0 ; Configure H0 (bed) heater model
M307 H1 A338.3 C210.6 D3.6 B0 ; Configure H1 (print head) heater model

M143 S320 ; Set max print head temperature
M143 H0 S140 ; Set max heat bed temperature
M570 H1 P10 T15 ; Configure heater safety timeouts

; Tool definition
M563 P0 D0 H1 ; Define tool 0
G10 P0 S0 R0 ; Set tool 0 operating and standby temperatures
M563 P2 H0 ; define heat bed tool
G10 P2 S0 R0 ; define heat bed tool op and standby temps
;M572 D0 S0.20

; Configure filament monitor
M581 T2 E0 S0 C1

; Reset filament monitor when the board is rebooted
M42 P63 S0
G4 P50
G4 P50
M42 P63 S1

T0 ; select first hot end

@Phaedrux

@Phaedrux what is the recommended app for reading the card on a PC? I’ve seen not to use notes as it can corrupt the files.

@Phaedrux unfortunately no

@droftarts

Ethernet hasn’t changed. When I search the IP on the web browser the green light on the duet port blinks but still says “took too long to respond”

This is with a new regular Ethernet cord.

@droftarts duet is set to 192.168.2.1
Actual is still 0.0.0.0

@droftarts!

@droftarts I get a green flashing light when I first plug in the Ethernet cable but then it stops. I’ll try to swing by my shop tomorrow, otherwise it might be Tuesday next week before I get back to it. Thank you for the help.
The Ethernet cable came with the machine but I’ve also tried a cross over cable for every option in case that was part of the issue but I get the same results. I can try another cable in case that’s the issue.

@droftarts

@droftarts

@droftarts Respectfully, x.x.2.2 is the duet IP address in the instructions and diagram. I recommend a change to the instructions if that is incorrect.

Yes, the amber light is constantly on and the green light does not stay on or flicker.

@droftarts Thank you for the response.

I followed the directions of that link.

Anything else I can try?
I feel like I’m just missing something I don’t know about.

Hello all.
I work with a fusion3 f410 3D printer with a Duet2 and am trying to get to DWC. I CANNOT have access to a router so I’m trying to set up direct wired connection from the duet to windows10 PC with wifi disabled to isolate IP.

I’ve tried following the directions from about every post on this topic I can find and nothing is working.

I also tried set a static IP on pc
IP 192.168.1.2
Subnet 255.255.255.0
gateway 192.168.1.1

And set on the duet
IP 192.168.2.3
Subnet 255.255.255.0 (as one other post said worked for them)
Gateway 192.168.1.1

I first tried set a static IP on pc
IP 192.168.2.2
Subnet 255.255.0.0
gateway 192.168.2.1

And set on the duet
IP 192.168.2.3
Subnet 255.255.0.0 (worked for someone else on a post when x.x.255.0 didn’t)
Gateway 192.168.2.1

Web browser gives back “this site can’t be reached. Took too long to respond” any way I try.

Can’t ping the board through Command Prompt.

Any advice would be appreciated
Thank you for assistance in advance