Posts made by idaho creator

@Phaedrux Ok I will contact filastruder. Thanks

@Phaedrux Thanks for the information. I probably wont jump on that bandwagon as of yet but maybe in the future as none of those features currently benifit me. I felt octoprint was a waste of time thats why I went with Duet to begin with and I could care less about photographing my print cause who really cares what a print actually looks like till its done.

@fcwilt My wifi router for this section of the house is just on the other side of the wall. It has no issues connecting when it does but there are times it just wont connect.

It has now deleted everything in the config.g file but left the empty file. This is getting annoying I have not used it in a week because of this still occurring.

@fcwilt Yea my network is channels is not near any other channel nearby. wifi signal strength is really good and the duet 3 connects but after a reset it might not connect until reset again. some times its several attempts sometimes its just once.

Im thinking of using a sbc with my duet 3 mini but I have searched to see what the benefit but cant find any info. Thanks for the help

@Phaedrux So its been a bit but It occured again jsut a moment ago. The system only deleted config.g in the system file. it left the config.g.bak so I was able to correct. This occured when I was saving the config.g after editing it with the web server editing feature and this is on a 3rd sd card that is new and high end fast read and write speed. It still has issue with locking on to wifi when reset with the router is 10 feet away in the next room.

@T3P3Tony I had used different sd card and problem still occurred but that macro was still in macro folder. It has been deleted.

@Phaedrux I purchased through filastruder. I am still having wifi issues were it wont connect to wifi either about every other reset. sometimes it connects but sometimes I have to reset board 2 or 3 times.

@T3P3Tony if you are referencing 2_tests_completed macro yes I have that macro but I dont use macros. I will delete it.

@T3P3Tony no it doesnt. The picture in the second post is what is left in the folder. I am also having to fight the board connecting to the wifi. It occurs now every other reset making me have to reset by pressing the stop button on the duet mini.

I will lock the file. It is frustrating to have it happen the first several times it was bad cause I didnt have back up. now I have backup but I have made changes and have to figure out. I now have a rolling backup I manually do.

M122
=== Diagnostics ===
RepRapFirmware for Duet 3 Mini 5+ version 3.2 running on Duet 3 Mini5plus WiFi (standalone mode)
Board ID: UWSLD-U296U-D65J0-40KMS-1H03Z-7UQUB
Used output buffers: 3 of 40 (15 max)
=== RTOS ===
Static ram: 98732
Dynamic ram: 108252 of which 40 recycled
Never used RAM 38192, free system stack 200 words
Tasks: NETWORK(ready,190) HEAT(blocked,316) CanReceiv(blocked,947) CanSender(blocked,372) CanClock(blocked,363) TMC(blocked,104) MAIN(running,444) IDLE(ready,20) AIN(blocked,267)
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 00:00:33 ago, cause: software
Last software reset at 2021-02-17 22:00, reason: User, GCodes spinning, available RAM 38192, slot 0
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00000000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Aux0 errors 0,0,0
Aux1 errors 0,0,0
Supply voltage: min 0.0, current 24.5, max 24.6, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: position 0, standstill, SG min/max 0/0, read errors 0, write errors 1, ifcnt 85, reads 4809, writes 9, timeouts 0, DMA errors 0
Driver 1: position 0, standstill, SG min/max 2/2, read errors 0, write errors 1, ifcnt 85, reads 4809, writes 9, timeouts 0, DMA errors 0
Driver 2: position 0, standstill, SG min/max 0/0, read errors 0, write errors 1, ifcnt 85, reads 4809, writes 9, timeouts 0, DMA errors 0
Driver 3: position 0, standstill, SG min/max 0/0, read errors 0, write errors 1, ifcnt 79, reads 4809, writes 9, timeouts 0, DMA errors 0
Driver 4: position 0, standstill, SG min/max 0/0, read errors 0, write errors 1, ifcnt 79, reads 4809, writes 9, timeouts 0, DMA errors 0
Driver 5: position 0, assumed not present
Driver 6: position 0, assumed not present
Date/time: 2021-02-17 22:00:54
Cache data hit count 70097951
Slowest loop: 5.00ms; fastest: 0.12ms
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 22.5MBytes/sec
SD card longest read time 1.0ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1, chamberHeaters = -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 12.07ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8

• WiFi -
  Network state is active
  WiFi module is connected to access point
  Failed messages: pending 0, notready 0, noresp 0
  WiFi firmware version 1.25
  WiFi MAC address f4:cf:a2:6f:bd:71
  WiFi Vcc 3.34, reset reason Power up
  WiFi flash size 2097152, free heap 26176
  WiFi IP address 192.168.1.55
  WiFi signal strength -53dBm, mode 802.11n, reconnections 0, sleep mode modem
  Clock register 00002002
  Socket states: 0 0 0 0 0 0 0 0
  === CAN ===
  Messages queued 303, send timeouts 301, received 0, lost 0, longest wait 0ms for reply type 0, free buffers 16

Yea I am now having wifi dropping again. each time I boot I run the risk of the system no reconnecting to wifi. I have tried new sd cards and I am just getting tired of it. I updated firmware the last time and it worked fine for just over a month. I wish I could get it figured out.

@alankilian yea I aint deleting it it is getting deleted on its own and why. Thats why I am here asking for help

My config.g file keeps getting deleted.

So I thought the problem was fixed. Did several prints some lasting 20+ hrs. Powered off yesterday due the hotend thermistor reading -273 degrees. Turned it on today to heat up block to remove themistor tube that is stuck due to plastic stuck on hotend from failed bed adheasion several prints ago. When fired up panel due stuck in connecting status. tried to connect to WBC and nothing there. Removed sd card and plugged into printer and again the config.g file missing. Why is my duet 3 mini wifi doing this. The only other post of this happening was my prior post a month ago. Started new thread because forum software said I needed to cause other post was old.

Just had to power off printer and printer would not reconnect to wifi after 2 power resets

Never mind I miss read your post I did not see the offset, Ill fix that