@droftarts thank you for helping!
yeah, the dimensions are standard and I printed already but I have some issues with the bed leveling.
I changed the mesh file to no_mesh and it is running now but it stopped during the mesh compensation because of the z probe problem...
I tried to run delta calibration several times and still, I have a z-probe error.
from the seemecnc menual
-All SeeMeCNC Delta’s no longer use mesh (bed map) calibration as of November 2022.
-The “Delta Calibration” now automatically deletes config-override.g and heightmap.csv files, then runs the Delta Calibration routine. There is no longer a need to manually delete files.
-"SeeMeCNC continues to NOT use bed mapping. It should not be necessary.
Calibration is only G32, or wavy icon on touch screen, or web control dashboard “Delta Calibration” drop box (middle screen)"
after G32
after this G32 calibration, does the printer consider the deviation on the bed?
bed mapping Is empty
after I G29 it says "seemecnc does not use bed mapping.."
I press ok and nothing, the bed mapping doesn't work.
from the seemecnc manual:
RostockMAX v3.2
Edit the config.g file items below, save and power cycle your printer
M665 Arms length and type
M569 Motor Direction - if G28 sends the hot end towards the bed, you’ll need to reverse the setting - If they’re set “S0”, set to “S1” to reverse direction and vice-versa. Check that extruders are turning in the correct direction as well.
M92 Stepper motor AND pulley number of teeth
Early machines had 20T timing pulleys, adjust the steps/mm accordingly
Late model machines have 16T timing pulleys
You also need to consider 1.8deg early model or late model 0.9 degree steppers
M558 Probe Settings (we did not ship FSR bed sensors in this printer model)
I don't know if I need to change something in the config file.. and I don't know the parameters of the printer.
I also posted about it in the seemecnc forum.
thank you!
@droftarts Sorry, didn't get you...
in the plugins, there is no bed mesh...
and when I ran G29 I got the first image "seemecnc does not use bed mapping...""
@droftarts
I mean that in the seemecnc manual, they say not to use a "run mash"
after G29
plugins
bed map
@droftarts hey, thank you.
i updated with seemecnc files https://docs.google.com/document/d/1IQf191FP7EgV8IRpa__jZviF_lfd1jcKVwHD2J7U9pw/edit
page 14: "At the web browser control “Dashboard”, select “Delta Calibration” from the drop down menu “Compensation & Calibration” (do not run “Mesh”)"
the photo of the bed is with the old version, I don't see a photo like this now after Calibration(maybe if I run mesh?)
I will check the delta calibration manual
ok, I succeeded in updating and connecting.
now how can I adjust the bed level?
when I do a G32 (delta calibration) is it consider the differences on the bed while printing?
m115
FIRMWARE_NAME: RepRapFirmware for Duet 2 WiFi/Ethernet FIRMWARE_VERSION: 3.4.4 ELECTRONICS: Duet WiFi 1.02 or later FIRMWARE_DATE: 2022-10-20 16:17:41
thank you!
@droftarts Yeah I have an old version..
I tried to update and now I cannot connect to the internet I got this error
M587 S"xxx" P"xxx"
Error: Failed to add SSID to remembered list<LF>ok<LF>
what is wrong?
after m122
M122
=== Diagnostics ===<LF>RepRapFirmware for Duet 2 WiFi/Ethernet version 3.0 running on Duet WiFi 1.02 or later<LF>Board ID: 08DDM-9FAM2-LW4S4-6J1DJ-3S86K-TJSRX<LF>Used output buffers: 4 of 24 (4 max)<LF>=== RTOS ===<LF>Static ram: 30516<LF>Dynamic ram: 90640 of which 580 recycled<LF>Exception stack ram used: 312<LF>Never used ram: 9024<LF>Tasks: NETWORK(ready,1888) HEAT(blocked,1464) MAIN(running,3740) IDLE(ready,156)<LF>Owned mutexes:<LF>=== Platform ===<LF>Last reset 00:08:13 ago, cause: power up<LF>Last software reset at 2023-11-18 14:58, reason: User, spinning module GCodes, available RAM 5648 bytes (slot 3)<LF>Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task 0xffffffff<LF>Error status: 0<LF>Free file entries: 10<LF>SD card 0 detected, interface speed: 20.0MBytes/sec<LF>SD card longest block write time: 0.0ms, max retries 0<LF>MCU temperature: min 31.8, current 34.5, max 34.7<LF>Supply voltage: min 12.2, current 12.2, max 12.3, under voltage events: 0, over voltage events: 0, power[Warning: Maximal number of characters per line exceeded! Check the line break settings in [Terminal > Settings > Text] or increase the limit in [Terminal > Settings > Advanced].]
the printer is Rostock MAX v3.2 delta
thank you.
Hello,
I have an error when I do a bed mapping M98 P"0 (photo attached)
when I do the first probe I get this resole (photo attached),
my bed is not leveled well, does the duet consider that? the changes on the bed while printing? or do I need to adjust the bed manually?
thanks.
maybe someone can help with that. now after I changed the sd card files to Rostockmax v3.2 files and try to do first probe or firmware update I didn't get any response. (the firmware updated to 1.21)
update:
https://ibb.co/cuEV0o
first probe:
thanks for the help.
Adi.
I can enter now, I got this error when I start.
https://ibb.co/eqV31T
thanks.
when I run the duet, the sd card must be inside? there must to some files?
I tried to run the duet with the SD card(pressed until clicks) and without it.
it still rejected.
actually, when I connected the SD card to PC I had an error that was fixed by the computer, it seems that it works ok.
maybe to try a different SD card?
what can be the problem?
https://ibb.co/njRg38
I updated the firmware to 1.21, DWC not updated.
I updated to 1.21, I can enter now, thanks a lot.
what is DWC?
I didn't find any IP address to change in a config file (sys folder)
Microsoft edge:
https://ibb.co/kxDKJ8
chrome (nothing)
https://ibb.co/eQqoBT
I don't know which port number to use in telnet command.
this is the photo
https://ibb.co/bykGy8
thanks.
sorry, but I didn't understand.
what command to right exactly? and which port I need to use for the command?
thanks,
Adi.
I ping the IP this is the result,
this is the photo
https://ibb.co/i0BpWJ
I am using PC and I tried to connect with chrome and Microsoft edge, I got nothing "cannot reach the address".
Hello,
I got to step 7 in this guide, I am using windows 10. https://duet3d.dozuki.com/Guide/1.9+Getting+Connected+to+your+Duet/7
I got the IP and the duet is connected.
but I cannot reach the duet whet I writing the IP into the browser.
do you know what it can be?
thanks,
Adi.