Posts made by myersm1234

@droftarts Sounds good. Let me know how you make out!

@droftarts I am using just the 4-wire and everything is working fine. Not sure why I had both connections in use, I must have miss read something when I was building this printer years ago. The 10 pin was 130cm long.
Any way sorry for the trouble and thanks again for the help!
Mike

@droftarts I don't see anything that looks like it could be shorting. Firmware is 3.5.0-rc9-v3-7.0 and I have both the ribbon and 4-wire connected.

@Phaedrux I found the problem. When the Panel Due 7 is plugged in it will not recognize the accelerometer

@Phaedrux With everything unplugged it is recognized on both boards. I guess I'll start plugging things back.

@Phaedrux Same thing with the update. If I just unplug everything from the board in place, this should give the same result as on the bench correct?

@Phaedrux No I haven't done the update. I will do this before I put it on the bench

@droftarts Hello I received a new accelerometer. Unfortunately I'm having the same issue. Could it be the Duet 2 board? Everything else seems to work with the board though.

@droftarts Looks like I bought it at Spool3d on Oct.20/23, but just getting to install it now...lol. Probably not worth the effort for warranty, for the cost of a new one.

@droftarts Thanks Ian, I really appreciate your help with this.
Thanks again! Mike

@droftarts said in Accelerometer not found on specified port:

This is with the Duex5 disconnected.
M98 P"config.g"
HTTP is enabled on port 80
Error: Accelerometer not found on specified port
Error: Driver 6 does not support mode 'spreadCycle'
Error: Driver 7 does not support mode 'spreadCycle'
Error: Driver 8 does not support mode 'spreadCycle'
Error: Driver 9 does not support mode 'spreadCycle'
Warning: Heater 0 predicted maximum temperature at full power is 321°C
Warning: Sensor number 1 has not been defined
Warning: Heater 0 predicted maximum temperature at full power is 691°C
Error: Heater 1 not switched on due to bad model

@droftarts Thank you sir, I will get this done tomorrow night.

@droftarts This is what I get
M955 P0
Error: M955: Accelerometer not found

; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.5.0-rc.4+1 on Sat Apr 13 2024 14:49:41 GMT-0400 (Eastern Daylight Time)

; General
G90 ; absolute coordinates
M83 ; relative extruder moves
M550 P"My Printer" ; set hostname
M911 S12 R12.5 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss

; Accessories
M575 P1 S0 B57600 ; configure PanelDue support

; Network
M552 S1 ; configure WiFi adapter
M586 P0 S1 ; configure HTTP

; Accelerometers
M955 P0 C"spi.cs2+spi.cs1" I61 ; configure accelerometer on board #0

; Smart Drivers
M569 P0 S0 D2 ; driver 0 goes backwards (X axis)
M569 P1 S0 D2 ; driver 1 goes backwards (Y axis)
M569 P4 S1 D2 ; driver 4 goes forwards (extruder 0)
M569 P6 S1 D2 ; driver 6 goes forwards (Y axis)
M569 P7 S0 D2 ; driver 7 goes backwards (Z axis)
M569 P8 S0 D2 ; driver 8 goes backwards (Z axis)
M569 P9 S0 D2 ; driver 9 goes backwards (Z axis)

; Motor Idle Current Reduction
M906 I30 ; set motor current idle factor
M84 S30 ; set motor current idle timeout

; Axes
M584 X0 Y1:6 Z7:8:9 ; set axis mapping
M671 X7:320:500 Y145:500:145 S99
M350 X16 Y16 Z16 I1 ; configure microstepping with interpolation
M906 X1200 Y1200 Z1200 ; set axis driver currents
M92 X106.67 Y106.67 Z400 ; configure steps per mm
M208 X0:500 Y0:500 Z0:450 ; set minimum and maximum axis limits
M566 X900 Y900 Z12 ; set maximum instantaneous speed changes (mm/min)
M203 X18000 Y18000 Z180 ; set maximum speeds (mm/min)
M201 X600 Y600 Z200 ; set accelerations (mm/s^2)

; Extruders
M584 E4 ; set extruder mapping
M350 E16 I1 ; configure microstepping with interpolation
M906 E1200 ; set extruder driver currents
M92 E282.94 ; configure steps per mm
M566 E120 ; set maximum instantaneous speed changes (mm/min)
M203 E3600 ; set maximum speeds (mm/min)
M201 E250 ; set accelerations (mm/s^2)

; Kinematics
M669 K0 ; configure Cartesian kinematics

; Probes
M558 K0 P9 C"^zprobe.in" H5 F6000:120:120 T18000 ; configure BLTouch probe via slot #0
G31 P500 X0 Y0 Z3.6 ; set Z probe trigger value, offset and trigger height
M950 S0 C"duex.pwm1" ; create servo #0 for BLtouch

; Endstops
M574 X1 P"xstop" S1 ; configure X axis endstop
M574 Y1 P"ystop" S1 ; configure Y axis endstop
M574 Z1 S2 ; configure Z axis endstop

; Mesh Bed Compensation
M557 X25:475 Y25:475 S50:50 ; define grid for mesh bed compensation

; Sensors
M308 S0 P"bedtemp" Y"thermistor" A"Heated Bed" T100000 B4725 C7.06e-8 ; configure sensor #0
 ; configure sensor #1

; Heaters
M950 H0 C"bedheat" T0 ; create heater #0
M143 H0 P0 T0 C0 S140 A0 ; configure heater monitor #0 for heater #0
M307 H0 R2.43 D5.5 E1.35 K0.56 B1 ; configure model of heater #0
M950 H1 C"e0heat" T1 ; create heater #1
M143 H1 P0 T1 C0 S285 A0 ; configure heater monitor #0 for heater #1
M307 H0 R0.418 K0.0323:0.000 D1.35 E1.35 S1.00 B0 ; configure model of heater #1

; Heated beds
M140 P0 H0 ; configure heated bed #0

; Fans
M950 F0 C"fan0" ; create fan #0
M106 P0 S0 L0 X1 B1 ; configure fan #0
M950 F1 C"fan1" ; create fan #1
M106 P1 S0 B1 H1 T45 ; configure fan #1
M950 F2 C"fan2" ; create fan #2
M106 P2 S0 L0 X1 B1 ; configure fan #2

; Tools
M563 P0 S"Micro Swiss" D0 H1 F1 ; create tool #0
M568 P0 R0 S0 ; set initial tool #0 active and standby temperatures to 0C

; Miscellaneous
T0 ; select first tool

@droftarts do you have any more suggestions ?

@jay_s_uk yes I did

@jay_s_uk any thoughts on what might be my problem?

Here is what I have.
M115
FIRMWARE_NAME: RepRapFirmware for Duet 2 WiFi/Ethernet FIRMWARE_VERSION: 3.5.0-rc.3 ELECTRONICS: Duet WiFi 1.02 or later + DueX5v0.11 FIRMWARE_DATE: 2024-01-24 17:56:24

Tried on Duet 2 board with daughter board removed
M955 P0 C"spi.cs2+spi.cs1" I61 .
No Luck!

@jay_s_uk I will remove the board and try that also.

I have tried on the Duet 2 board but on top of the daughter board same deal not found. I will get some pics tonight.
Thanks for the help!