Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login
    1. Home
    2. pao_wikhan
    • Profile
    • Following 0
    • Followers 0
    • Topics 9
    • Posts 65
    • Best 0
    • Controversial 0
    • Groups 0

    pao_wikhan

    @pao_wikhan

    0
    Reputation
    1
    Profile views
    65
    Posts
    0
    Followers
    0
    Following
    Joined Last Online

    pao_wikhan Unfollow Follow

    Latest posts made by pao_wikhan

    • RE: baby steps not working

      @dc42
      so it would not reflect the z position in dwc?
      it is hard to tell if the baby steps did take effect

      That's correct, the Z position displayed in DWC is the commanded Z position, not the Z position after allowing for tool offset, workplace coordinate offset, bed compensation, axis skew compensation or baby stepping. However, DWC shows the current baystep offset on the Status (or Print Status) page.

      posted in General Discussion
      pao_wikhanundefined
      pao_wikhan
    • baby steps not working

      upgraded from 1.21rc2 to 1.22, and it seems no matter how i tick baby steps it doesnt show on Z axis.

      to

      Firmware Name: RepRapFirmware for Duet 2 WiFi/Ethernet
      Firmware Electronics: Duet WiFi 1.02 or later
      Firmware Version: 2.02(RTOS) (2018-12-24b1)
      WiFi Server Version: 1.22
      Web Interface Version: 1.22.6

      posted in General Discussion
      pao_wikhanundefined
      pao_wikhan
    • RE: H1 giving erratic reads while printing.

      @dc42

      well 4hrs into printing, i think the e3d sensor (blue wire) did the trick. odd though cause when i measure the resistance its like 70k-100kohm and not the pt100 value of below 100ohms. its now cleaner than ever. i also replaced the cartridge and moved back to a newer 24V 50W ceramic type with 100% pwm.

      0_1550324881791_3a541f4a-825f-41d5-b333-4067f20761bd-image.png

      posted in Tuning and tweaking
      pao_wikhanundefined
      pao_wikhan
    • RE: H1 giving erratic reads while printing.

      if it happens again, i think the heatblock screw holding the sensor is not gripping correctly, but that is a long shot. (my theory that is.)

      posted in Tuning and tweaking
      pao_wikhanundefined
      pao_wikhan
    • RE: H1 giving erratic reads while printing.

      @dc42
      new thermistor, on that pic..
      i replaced it with the one included in e3d v6, seems stable so far. but i didnt connect it to the daughter board as its not giving any values.

      posted in Tuning and tweaking
      pao_wikhanundefined
      pao_wikhan
    • RE: H1 giving erratic reads while printing.

      okay its happening again. now im not sure if my duet is broken

      0_1550300896097_e394e059-0950-4b2d-9984-818623b2748e-image.png

      posted in Tuning and tweaking
      pao_wikhanundefined
      pao_wikhan
    • RE: H1 giving erratic reads while printing.

      Thanks @dc42 @deckingman @T3P3Tony
      i fixed it, seems like the thermistor is getting pulled and something was shorting the 5v rail. still using the new cartridge and ntc sensor (the pt100 was giving 2000degrees, but rtc1 is working when i place a 100ohm resistor) will troubleshoot that in a new chapter.
      oh and a new psu too, seems like the psu was heavily grounded.
      0_1550296538601_70f39bd6-45d9-49be-852d-d05853d37330-image.png

      posted in Tuning and tweaking
      pao_wikhanundefined
      pao_wikhan
    • RE: H1 giving erratic reads while printing.

      @deckingman
      rewiring is the same..oscillations..will try using e3d generic 24v 30W heater..then tune to max P1

      posted in Tuning and tweaking
      pao_wikhanundefined
      pao_wikhan
    • RE: H1 giving erratic reads while printing.

      thats the thing. it was working for the past few month, didnt touch anything print print print. now this giving me that erratic motion is weird. so i replaced the sensor same output, and did the stuff recommended here.
      just finished rewiring really, so im testing.

      posted in Tuning and tweaking
      pao_wikhanundefined
      pao_wikhan
    • RE: H1 giving erratic reads while printing.

      @deckingman

      i think my issue is more than that..while printing it gives out erratic values from 210 down to 160-140, stopping the print

      posted in Tuning and tweaking
      pao_wikhanundefined
      pao_wikhan