Posts made by RKS7204

@rks7204 said in I think I found a bug:

M201 X1000.00 Y1000.00 Z1000.00 E1000.00 ; set accelerations (mm/s^2)

My accelerations (as listed above) are not even near those high numbers.

@rjenkinsgb
The power is not controlled by the duet bord.
I use a physical switch on the printer.
When the printer is off, there is no power suplied to the board.

Steve

@rjenkinsgb

That doesn't make a difference

Steve

@phaedrux
When i power on the printer. Ik get these errors. And the motors don't move. After I reset the printer with M999 the errors are gone. I can start printing.

Steve

@Phaedrux

After sending M999 all motors are moving. If I don't send M999 I get the "disconnected" error. I believe that if it is a bad crimp, sending M999 wouldn't solve it.

23/12/2021 23:14:33 M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.4.0beta7 (2021-12-16 12:22:11) running on Duet Ethernet 1.02 or later
Board ID: 08DGM-95BNL-MGPSN-6JKFJ-3S86L-12XRX
Used output buffers: 3 of 24 (19 max)
=== RTOS ===
Static ram: 23804
Dynamic ram: 68812 of which 0 recycled
Never used RAM 19344, free system stack 136 words
Tasks: NETWORK(ready,26.3%,230) HEAT(notifyWait,0.0%,330) Move(notifyWait,0.0%,305) MAIN(running,73.6%,440) IDLE(ready,0.1%,30), total 100.0%
Owned mutexes:
=== Platform ===
Last reset 00:12:10 ago, cause: software
Last software reset at 2021-12-23 23:02, reason: User, GCodes spinning, available RAM 19320, slot 1
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Aux0 errors 0,0,0
Step timer max interval 0
MCU temperature: min 22.6, current 24.9, max 25.2
Supply voltage: min 24.2, current 24.4, max 24.5, under voltage events: 0, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Events: 0 queued, 0 completed
Driver 0: pos 81255, standstill, SG min 0
Driver 1: pos 80409, standstill, SG min 15
Driver 2: pos 80836, standstill, SG min 49
Driver 3: pos 0, standstill, SG min n/a
Driver 4: pos 0, standstill, SG min n/a
Driver 5: pos 0
Driver 6: pos 0
Driver 7: pos 0
Driver 8: pos 0
Driver 9: pos 0
Driver 10: pos 0
Driver 11: pos 0
Date/time: 2021-12-23 23:14:31
Cache data hit count 4294967295
Slowest loop: 13.25ms; fastest: 0.17ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 1.0ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, segments created 5, maxWait 22861ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 5, completed 5, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters 0 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0
Heater 1 is on, I-accum = 0.0
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty
=== Network ===
Slowest loop: 17.56ms; fastest: 0.02ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8
Interface state active, link 100Mbps full duplex

TripodMaker
Status
Idle
Mode: FFF
Tool Position
X
0.0
Y
0.0
Z
500.60
Extruder Drives
Drive 0
0.0
Speeds
Requested Speed
0 mm/s
Top Speed
0 mm/s
Sensors
Vin
24.4 V
MCU Temperature
24.8 °C
Z-Probe
542
Tools
Extra
Control Heaters
Tool Heater Current Active Standby Tool 0
T0 - Load Filament Heater 1
active 18.5 °C

Bed Heater 0
off 18.1 °C

Temperature Chart
23/12/2021 23:15:50 M98 P"config.g"
HTTP is enabled on port 80
FTP is enabled on port 21
TELNET is disabled

Config.g :

; Configuration file for Duet WiFi (firmware version 3.3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.3.10 on Tue Dec 21 2021 21:14:01 GMT+0100 (Midden-Europese standaardtijd)

; General preferences
M575 P1 S1 B57600 ; enable support for PanelDue
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"TripodMaker" ; set printer name
M665 R167.220 L350.3926 B160 H505.578 X0.345 Y0.210 Z0; Set delta radius, diagonal rod length, printable radius and homed height
M666 X0.38 Y-0.02 Z-0.36 ; Put your endstop adjustments here, or let auto calibration find them

; Network
M552 P0.0.0.0 S1 ; enable network and acquire dynamic address via DHCP
M586 P0 S1 ; enable HTTP
M586 P1 S1 ; enable FTP
M586 P2 S0 ; disable Telnet

; Drives
M569 P0 S1 ; physical drive 0 goes forwards
M569 P1 S1 ; physical drive 1 goes forwards
M569 P2 S1 ; physical drive 2 goes forwards
M569 P3 S1 ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X100.00 Y100.00 Z100.00 E166.00 ; set steps per mm
M566 X1200.00 Y1200.00 Z1200.00 E1200.00 ; set maximum instantaneous speed changes (mm/min)
M203 X18000.00 Y18000.00 Z18000.00 E1200.00 ; set maximum speeds (mm/min)
M201 X1000.00 Y1000.00 Z1000.00 E1000.00 ; set accelerations (mm/s^2)
M906 X1000 Y1000 Z1000 E800 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Axis Limits
M208 Z0 S1 ; set minimum Z

; Endstops
M574 X2 S1 P"xstop" ; configure switch-type (e.g. microswitch) endstop for high end on X via pin xstop
M574 Y2 S1 P"ystop" ; configure switch-type (e.g. microswitch) endstop for high end on Y via pin ystop
M574 Z2 S1 P"zstop" ; configure switch-type (e.g. microswitch) endstop for high end on Z via pin zstop

; Z-Probe
M558 P1 C"!zprobe.in" H5 F120 T6000 R1 A5 X0 Y0 Z0 ; set Z probe type to unmodulated and the dive height + speeds
G31 P800 X0 Y0 Z-0.1 ; set Z probe trigger value, offset and trigger height
M557 R145 S20 ; define mesh grid

; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M307 H0 R0.228 K0.256:0.000 D3.08 E1.35 S1.00 B0 ; enable PID mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M308 S1 P"e0temp" Y"thermistor" T100000 B4725 C7.06e-8 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S280 ; set temperature limit for heater 1 to 280C

; Fans
M950 F0 C"fan0" Q250 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q250 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on
;M950 F2 C"fan2" Q250 ; create fan 2 on pin fan2 and set its frequency
;M106 P2 S2 H100:101:102 T44:65 L0.3 ; set fan 2 value. Thermostatic control is turned on
M308 S2 Y"drivers" A"DRIVERS" ; configure sensor 2 as temperature warning and overheat flags on the TMC2660 on Duet
M308 S3 Y"mcu-temp" A"MCU" ; configure sensor 3 as on-chip MCU temperature sensor
M950 F2 C"fan2" Q100 ; create fan 2 on pin fan2 and set its frequency
M106 P2 H2:3 L0.15 X1 B0.3 T40:70 ; set fan 2 value

; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X9 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
T0 S0 ; select first tool
M912 P0 S3.2 ; calibrate MCU temp

HomeDelta.g :

; homedelta.g
; called to home all towers on a delta printer
;
; generated by RepRapFirmware Configuration Tool v3.3.10 on Tue Dec 21 2021 22:18:44 GMT+0100 (Midden-Europese standaardtijd)
G91 ; relative positioning
G1 H1 X805 Y805 Z805 F1800 ; move all towers to the high end stopping at the endstops (first pass)
G1 H2 X-5 Y-5 Z-5 F1800 ; go down a few mm
G1 H1 X10 Y10 Z10 F360 ; move all towers up once more (second pass)
G1 Z-5 F6000 ; move down a few mm so that the nozzle can be centred
G90 ; absolute positioning
G1 X0 Y0 F6000 ; move X+Y to the centre

Steve

Hello,

My printer is a delta printer
Board: Duet 2 Ethernet (2Ethernet)
Firmware: RepRapFirmware for Duet 2 WiFi/Ethernet 3.4.0beta7 (2021-12-16)

I have to run M999 after startup. If I don't do that I get errors, and the head won't move.

23/12/2021 23:02:49 G28
23/12/2021 23:02:38 Connection established
23/12/2021 23:02:31 Connection interrupted, attempting to reconnect...
HTTP request timed out
23/12/2021 23:02:22 M999
23/12/2021 23:02:14 Error: G0/G1: insufficient axes homed
23/12/2021 23:02:13 Warning: Driver 1 warning: phase A may be disconnected, phase B may be disconnected
Warning: Driver 2 warning: phase A may be disconnected, phase B may be disconnected
Warning: Driver 0 warning: phase A may be disconnected, phase B may be disconnected
23/12/2021 23:01:45 G28
Warning: Driver 1 warning: phase A may be disconnected, phase B may be disconnected
Warning: Driver 2 warning: phase A may be disconnected, phase B may be disconnected
Warning: Driver 0 warning: phase A may be disconnected, phase B may be disconnected

Steve

If I understand it correctly, it's like this:

My nozzle has an offset of 9 mm X direction to the center of the head.
I can choose the reference point where I want.
For 1 nozzle that would be the nozzle.
How does the printer know it has an offset of 9 mm?
And this is important for the build plate, how do I eliminate the 9mm offset in X direction. Like I have now.

When I add the 2nd nozzle,
I can choose to keep the HRP on nozzle 1, and give nozzle 2 an offset of -18 mm.
or I can set the HRP in the center of the head and gibe both nozzles a +/- 9mm offset.

I ment documentation on setting the head reference point.

Is there any documentation available? Couldn't find it.

Hi probably a dumb question, the z probe offset is related to the nozzle or to the center of the head?

Hello,

Great board, first print came out and was excellent.
No elephant feet, and the only noise is from the fans.

I'm using
Firmware Electronics: Duet Ethernet 1.0
Firmware Version: 1.19 (2017-08-14)
Web Interface Version: 1.19

I tried to calibrate.
My Z-probe sensor isn't installed yet.
I tried the manual calibration(Pressed Delta Calibration on the Machine Control), but that gives me only the possibility to change the X value, not the Z value.
Then I tried this http://www.escher3d.com/pages/wizards/wizarddelta.php and used the G-console. After calibrating things are even worse.

Is there a way to do manual calibration?

I powered up my ethernet board.

First thing, no network connection.
Because the Ip adres is hard coded to 192.168.1.14, and my subnet is 47.
So I had to change the IP adres to 192.16..47.80

Next question, I can't find an answer for.

I have the following on my printer
-3 ledstrips connected to 1 connector (always on fans)
-1 fan at the board connected to always on fans
-1 fan for the hotend connected to fan0
-3 fans for cooling the print connected to 1 connector connected to fan1

I'd like to have the following
Leds always on, Board Fan always on, hotend fan on when printing, print fans controlled by slicer off when printer is powered on

How do I do this?

Thanks

Probably a dumb question.

Is there a possibility to have 2 options for autocalibration? I have doors on my printer and when the doors are closed I have a printable diameter of 20 cm. When the doors are opened I have a printable diameter of 30 cm.

Is it easy to swap between 2 different sizes for autocalibration?

Everything arrived I'll be changing everything on Sunday (I hope).

ok, sorry I didn't understood it at once.

Maybe swapping the left and right column on the webpage is advised?

ok, so I take the max allowed values if my values are too big. Afterwards I have to adjust the generated files.
Can you give me a list of the files that needs adjustment and the commands inside them that needs adjustment?
How can I determine the steps/mm for the extruder and x/y/z motor?

Thanks for the links, but I can't use https://configurator.reprapfirmware.org/
My dimensions are too big
These are my dimensions Printerdimensions :42 cm x 53 cm x 101 cm, print area Ø 30 cm x 42 cm