Navigation

    Duet3D Logo

    Duet3D

    • Register
    • Login
    • Search
    • Categories
    • Tags
    • Documentation
    • Order
    1. Home
    2. RogerL
    • Profile
    • Following 0
    • Followers 0
    • Topics 10
    • Posts 23
    • Best 2
    • Groups 0

    RogerL

    @RogerL

    2
    Reputation
    2
    Profile views
    23
    Posts
    0
    Followers
    0
    Following
    Joined Last Online

    RogerL Unfollow Follow

    Best posts made by RogerL

    • GT2 high quality belts

      Hi,

      Where in Europe do I find highend GT2 belts online?
      What do I need to look for in a belt?

      Please move this post if its in the wrong category.

      posted in General Discussion
      RogerL
      RogerL
    • RE: Connecting a filabase silicon heater.

      @arnold_r_clark
      Thanks Arnold, really appreciate the help.

      posted in Duet Hardware and wiring
      RogerL
      RogerL

    Latest posts made by RogerL

    • RE: Connecting a filabase silicon heater.

      @arnold_r_clark
      Thanks Arnold, really appreciate the help.

      posted in Duet Hardware and wiring
      RogerL
      RogerL
    • RE: Connecting a filabase silicon heater.

      What kind of config did you guys use for the filafarm pad termistor?

      posted in Duet Hardware and wiring
      RogerL
      RogerL
    • RE: Connecting a filabase silicon heater.

      @arnold_r_clark
      You’re right, it was cut short inside the sleeve. Thank every one for the pointers.

      posted in Duet Hardware and wiring
      RogerL
      RogerL
    • RE: Connecting a filabase silicon heater.

      @arnold_r_clark
      Thanks for the info. Just need to figure out the one wire termistor to get going.

      posted in Duet Hardware and wiring
      RogerL
      RogerL
    • Connecting a filabase silicon heater.

      Hi

      Im about to rebuild my bed with a filabase bed from filafarm.

      Its a 230v silicon pad and it comes with a SSR.
      My old was a 24v bed.

      Do I run same 24v Duet wifi output to control my SSR?
      It seems as the termistor in my pad is a single wire 100k termistor, where on the Duet should I connect it?

      Going to ground my frame and put in a ground breaker too.

      posted in Duet Hardware and wiring
      RogerL
      RogerL
    • RE: MBLA, not getting it right.

      All good now with both changes, thank you

      posted in Tuning and tweaking
      RogerL
      RogerL
    • RE: MBLA, not getting it right.

      That worked but I got a new error
      G32
      Error: Bed calibration : 4 factor calibration requested but only 3 points provided

      posted in Tuning and tweaking
      RogerL
      RogerL
    • MBLA, not getting it right.

      Hi,

      I been reading instructions on how to configure manual bed leveling assistant but I cannot get it to work correctly.

      I have a carthesian printer and four corner screws to adjust my table.
      Can get it to probe using G32 and it does all my four corners but resports back a error:
      G32
      Error: Number of calibration factors (3) not equal to number of leadscrews (4)
      I been trying to figure out how to set this but no luck.

      Here are my Bed.g lines
      G28 ; home
      G30 P0 X0 Y0 Z-99999 ; probe near an adjusting screw
      G30 P1 X350 Y0 Z-99999 ; probe near an adjusting screw
      G30 P2 X350 Y223 Z-99999 ; probe near an adjusting screw
      G30 P4 X0 Y223 Z-99999 S3 ; probe near an adjusting screw and report adjustments needed

      Here is my config.g lines
      M671 X-15:350:350:-15 Y-12:-12:250:250 P1.0 ;

      Any ideas what I do wrong?

      posted in Tuning and tweaking
      RogerL
      RogerL
    • RE: Strange fan problem

      @Veti
      Yes I did, its working.

      Just because I wrote this post it now turns again.
      Whatever fixes the problem is good 😀

      posted in Duet Hardware and wiring
      RogerL
      RogerL
    • Strange fan problem

      Hi,
      I Duet wifi and I supply it with 24v
      I have a E3D v6 24v setup and corresponding e3D fan for hotend.

      All has been running great until the fan stopped, I have tested another fan and cables with no luck.

      The I took a multimeter and measured voltage on FAN1, it shows 12v.. I have not changed anything.. It should read 24v, right. FAN0 gives 24v..

      Can someone explain if Im being stupid or if something changed.. To make it even odder I tested with another Duet Wifi but with same config card.. same result 12 v on FAN1

      posted in Duet Hardware and wiring
      RogerL
      RogerL