Navigation

    Duet3D Logo

    Duet3D

    • Register
    • Login
    • Search
    • Categories
    • Recent
    • Tags
    • Documentation
    • Order
    1. Home
    2. siblues
    • Profile
    • Following
    • Followers
    • Topics
    • Posts
    • Best
    • Groups

    siblues

    @siblues

    4
    Reputation
    146
    Posts
    12
    Profile views
    0
    Followers
    3
    Following
    Joined Last Online

    siblues Follow

    Best posts made by siblues

    • RE: Motor phase disconnected problem?

      I had some motors on the way so I tried what Tony mentioned and it was a bad motor.

      posted in General Discussion
      siblues
      siblues
    • RE: Duet WiFi dont work

      Try following this step by step

      https://duet3d.dozuki.com/Guide/1.)+Getting+Connected+to+your+Duet/7

      posted in Duet Hardware and wiring
      siblues
      siblues
    • RE: Heat bed heater help?

      Thanks for the link the time it will take is a bit longer than what I am currently experiencing but it isn't too bad 10-12 minutes.The weird thing is the calculator only shows a 4 minute difference between the 300 and 600 w versions of the heater.The 600w is only available in the 110v or 220v versions.The 12v version looks like a better option for me with this printer,I will look into the 110v version and 24v PSU on my Corexy plans.

      posted in General Discussion
      siblues
      siblues

    Latest posts made by siblues

    • RE: Duet WiFi dont work

      Try following this step by step

      https://duet3d.dozuki.com/Guide/1.)+Getting+Connected+to+your+Duet/7

      posted in Duet Hardware and wiring
      siblues
      siblues
    • RE: Heat bed heater help?

      Thanks for the link the time it will take is a bit longer than what I am currently experiencing but it isn't too bad 10-12 minutes.The weird thing is the calculator only shows a 4 minute difference between the 300 and 600 w versions of the heater.The 600w is only available in the 110v or 220v versions.The 12v version looks like a better option for me with this printer,I will look into the 110v version and 24v PSU on my Corexy plans.

      posted in General Discussion
      siblues
      siblues
    • RE: Strange Heat Bed temperature curve

      I agree with Phaedrux.I was having the same issue and it was caused by a bad solder joint/connection on the thermistor wiring.

      posted in General Discussion
      siblues
      siblues
    • RE: Heat bed heater help?

      The heater can be purchased in either 300 or 400w versions and my PSU is a Meanwell 450 so I am guessing it will be stressed a bit but should be able to handle the load.

      posted in General Discussion
      siblues
      siblues
    • Heat bed heater help?

      I have a cartesian style printer with a heat bed size of 320 x 225.I have a .250 MIC6 plate on the way and I am planning on ordering a silicone heater for the printer from Keenovo.I have a few questions regarding the heater.I was planning on ordering a 12v version with an Auber or similar relay to use with my Wifi.I have a Meanwell power supply that has open 12v terminals so it can directly feed the heater and then the wifi can control it through the relay but I am unsure how long that would take to heat and whether or not I should try ordering and wiring up a 110v version to the mains.I plan on ordering the heater with a semitec thermistor and two openings in the center to allow me to install a replacement thermistor in the future if need be.The second opening would be for a thermal fuse location.The 12v version would be simpler and safer for me I believe although I am capable of wiring a 110v version.I would just prefer to stay away from ac if possible.I will use whichever one will help me get this printer functioning the way it was meant to be.Thanks

      posted in General Discussion
      siblues
      siblues
    • RE: Round heater on a square heat bed?

      Keenovo might be able to make a heater with the necessary bolt holes so the heater reaches all the edges.

      https://keenovo.store/

      posted in General Discussion
      siblues
      siblues
    • RE: Sudden consistent under-voltage events

      I had the same issue it was the wiring going into the Duet it seemed like it was tight but the actual plastic on the terminal was interfering with the connection.

      posted in General Discussion
      siblues
      siblues
    • RE: Thermocouple short question

      Have you tried checking continuity between the wiring and heater block?

      posted in Duet Hardware and wiring
      siblues
      siblues
    • RE: Magnetic Filament Sensor Updates?

      Have you received any of the assembled sensor boards yet?I would love to see any pictures you may have laying around.

      posted in Filament Monitor
      siblues
      siblues
    • RE: Expansion board with 5v drivers

      does the BLTouch deploy and retract when you issue the commands?

      This is the most thorough explanation I have found regarding setting it up on the Duet boards

      https://betrue3d.dk/bltouch-on-duet-wifi-configuratio-and-usage/

      posted in Accessories and Add-ons
      siblues
      siblues