Posts made by siladeniz

@Phaedrux

; homeall.g
; called to home all axes
;
; generated by RepRapFirmware Configuration Tool v3.3.16 on Thu Aug 31 2023 11:01:34 GMT+0200 (Central European Summer Time)
G91                     ; relative positioning
G1 H2 Z5 F6000          ; lift Z relative to current position
G1 H1 X-235 Y-215 F1800 ; move quickly to X and Y axis endstops and stop there (first pass)
G1 H2 X5 Y5 F6000       ; go back a few mm
G1 H1 X-235 Y-215 F360  ; move slowly to X and Y axis endstops once more (second pass)
G90                     ; absolute positioning
G1 X15 Y15 F6000        ; go to first bed probe point and home Z
G30                     ; home Z by probing the bed

; homex.g
; called to home the X axis
;
; generated by RepRapFirmware Configuration Tool v3.3.16 on Thu Aug 31 2023 11:01:34 GMT+0200 (Central European Summer Time)
G91               ; relative positioning
G1 H2 Z5 F6000    ; lift Z relative to current position
G1 H1 X-235 F1800 ; move quickly to X axis endstop and stop there (first pass)
G1 H2 X5 F6000    ; go back a few mm
G1 H1 X-235 F360  ; move slowly to X axis endstop once more (second pass)
G1 H2 Z-5 F6000   ; lower Z again
G90               ; absolute positioning

; homey.g
; called to home the Y axis
;
; generated by RepRapFirmware Configuration Tool v3.3.16 on Thu Aug 31 2023 11:01:34 GMT+0200 (Central European Summer Time)
G91               ; relative positioning
G1 H2 Z5 F6000    ; lift Z relative to current position
G1 H1 Y-215 F1800 ; move quickly to Y axis endstop and stop there (first pass)
G1 H2 Y5 F6000    ; go back a few mm
G1 H1 Y-215 F360  ; move slowly to Y axis endstop once more (second pass)
G1 H2 Z-5 F6000   ; lower Z again
G90               ; absolute positioning

; homez.g
; called to home the Z axis
;
; generated by RepRapFirmware Configuration Tool v3.3.16 on Thu Aug 31 2023 11:01:34 GMT+0200 (Central European Summer Time)
G91              ; relative positioning
G1 H2 Z5 F6000   ; lift Z relative to current position
G90              ; absolute positioning
G1 X15 Y15 F6000 ; go to first probe point
G30              ; home Z by probing the bed

; Uncomment the following lines to lift Z after probing
;G91             ; relative positioning
;G1 Z5 F100      ; lift Z relative to current position
;G90             ; absolute positioning

@jay_s_uk I am using one head which means one extruder at a time, but I couldn't use e0 motor with e1 heater and I just unplugged the e0 motor pin and put it to the e1 motor pin. and changed the d0 to d1. does it work if I use e0 motor pin, e1 thermistor and e1 heater?

I am using the DWC dashboard homing buttons.

@jay_s_uk Okay I changed the D0 to D1 and pluged the servo motor pin from e0 to e1 and its working no thank you for the help!!

but I still have issues with homing can you answer that please

@jay_s_uk when put P1 the name was showing up as Duet board, as you can see at the end of the heater part,thats why I used p2.

there was a continuity problem I change the cable and it solved.

For the extruder selection since I am using just one tool at a time I didn't change the extruder, should I still change it?
I try to load filament but it didn't work, does e0 driver work with second heater?
I tried to uncommenting
;M569 P5 S1 ; physical drive 5 goes forwards (E1 motor)
from the drives part
and I changed the D value to D1 in tool part
it didn't work.

lastly I changed the P5 to P7 since the P5 is used in drive 4, but there is an error now and it says drive 4 error: a and b phases may not be connected.

@jay_s_uk Also I want to ask another thing too, sometimes while I am homing the device it goes to the wrong way, even I didn't change anything on the config or I changed something unrelated to that(like heaters) it happens. what can it be the reason and can I fix it permanently?

@jay_s_uk hi thank you for the advise, I add to the config and i can see the heater 2 rightnow. but it shows -273C. is there a problem with my config or what should i do?

; Configuration file for Duet Ethernet (firmware version 3)
; executed by the firmware on start-up
;
; generated by Julian Zettl Feb 2022
; edited by Deniz and Tillman July 2023

; ================= General preferences ===================
G90                 ; send absolute coordinates...
M83                 ; ...but relative extruder moves
M550 P"BLV"         ; set printer name
M669 K1				; Select CoreXY mode


; ====================== Network ===========================
M552 S1                                       	; enable network
M552 P192.168.1.254								; set IP Address
M553 P255.255.255.0								; set Netmask
M554 P192.168.1.2								; Set default Gateway
M586 P0 S1                                    	; enable HTTP
M586 P1 S0                                  	; disable FTP
M586 P2 S0                                   	; disable Telnet

; ======================= Drives ===========================
M569 P0 S0                                      ; physical drive 0 goes backwards (A motor)
M569 P1 S0                                      ; physical drive 1 goes backwards (B motor)
M569 P2 S1                                      ; physical drive 2 goes forwards (alpha)
M569 P5 S0                                      ; physical drive 4 goes forwards (beta) 
M569 P6 S0 										; physical drive 6 goes forwards (gamma) 

M569 P3 S1                                      ; physical drive 3 goes forwards (E0 motor) 
;M569 P5 S1 										; physical drive 5 goes forwards (E1 motor) 
M584 X0 Y1 Z2:5:6 E3:4							; set drive mapping

; ===================== Drive Settings =====================
M350 X128 Y128 Z128:128:128 E128:128 I1			; configure microstepping with interpolation
M92  X1600 Y1600 Z12800:12800:12800 E3936:6400  ; steps per mm E1:800 E2:837
M566 X540 Y540  Z56:56:56 E480:480      		; maximum instantaneous speed changes mm/min
M203 X10000 Y10000 Z1800:1800:1800 E15000:15000	; maximum speeds (mm/s)
M201 X2000 Y2000 Z100:100:100 E1000:3000        ; set accelerations (mm/s^2)
M906 X1000 Y1000 Z800 E800 I50					; set motor currents (mA) and  idle %
M84 S120	                               	    ; Set idle timeout

; ================ Independent Z Leveleing =================
M671 X-170.24:170.24:0 Y-128.815:-128.815:130.75 S20	   	; leadscrew pivot point:

; ===================== Axis Limits ========================
M208 X-45 Y-36 Z0 S1                                      	; set axis min
M208 X270 Y270 Z200 S0                                  	; set axis max
;originally with 0,0 centered on bed:
;M208 X-152:150 Y-144:172

; ======================= Endstops =========================
M574 X1 S1 P"x_stop"   		; X min active high endstop switch
M574 Y2 S1 P"y_stop"   		; Y max active high endstop switch
M574 Z1 S2                  ; configure Z-probe endstop for low end on Z

; ======================== Z-Probe =========================
;M950

M558 P9 C"zprobe.in" H5 F120 T6000 ; Duet 2 WiFi/Ethernet, DueX2/5
M950 S0 C"duex.pwm1" ; Duet 2 WiFi/Ethernet + DueX2/5
;M307 H3 A-1 C-1 D-1 ; Disable heater 3 to free up PWM channel 1 on the Duex board.
;M558 P1 C"ZPROBE.IN" H5 F500 T1000	; Z Probe type=analog, pin, dive height+rate, travelspeed
;M280 P0 S90
G31 X27 Y58 Z1 P25
;G31 X0 Y0 Z0.2 P500					; Z Probe offset and trigger value
M557 X15:215 Y15:195 S60     		; define mesh grid

; ======================== Heaters =========================
;M305 P1 T100000 B4267 R4700		; old RRF2.x 
M301 H1 H2 P21.1 I0.816 D59.6  		;PID settings hotend from old config
M308 S1 P"e0temp" Y"thermistor" A"Hotend" T100000 B4267 R4700  	; extruder thermistor
M950 H1 C"e0heat" T1 	 								  		; link heater to sensor
M143 H1 S285		        									; temperature limit
M104 S0 
M308 S3 P"e1temp" Y"thermistor" A"Hotend2" T100000 B4267 R4700   ; configure sensor 3 as thermistor on pin e1temp
M950 H2 C"e1heat" T3                           ; create nozzle heater output on e1heat and map it to sensor 3
;M307 H2 B0 S1.00                               ; disable bang-bang mode for heater  and set PWM limit
M143 H2 S280                                   ; set temperature limit for heater 2 to 280C                                                        ; turn off  nozzle heater
M308 S0 P"bedtemp" Y"thermistor" A"Bed" T100000 B4267 R4700		; configure sensor 0 as thermistor on pin bedtemp
M950 H0 Q10 C"bedheat" T0                                   	; create bed heater output on bedheat and map it to sensor 0
M307 H0 A284.0 C843.8 D11.0 B0									; Heatbed PID
M140 H0 S0                                               		; map heated bed to heater 0
M143 H0 S100                                            		; set temperature limit for heater 0 to 120C

M308 S2 P"mcu-temp" Y"mcu-temp" A"Duet Board" 					; Configure MCU sensor

; ========================= Fans ===========================
M106 P0 S0.1 I0 F500 T45 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P1 S1 I0 F500 H1 T45 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on

M950 F0 C"fan0" Q250                	; create fan 1 on pin fan0 and set its frequency
M106 P0 C"hotend fan" T60 H1        	; P"fan1" C"displayname" T"triggervalue" H"heater1"

M950 F1 C"fan1"                
M106 P1 S100 

; ======================== Tools ===========================
M563 P0 S"FDM" D0 H1			; P"tool0" S"displayname" D"e0motor" H"heater1"
G10 P0 X0 Y0 Z0      			; set tool 0 axis offsets
G10 P0 R0 S0             		; set initial tool 0 active and standby temperatures to 0C
M563 P2 S"FDM" D0 H2			; P"tool2" S"displayname" D"e0motor" H"heater2"
G10 P2 X0 Y0 Z0      			; set tool 2 axis offsets
G10 P2 R0 S0             		; set initial tool 0 active and standby temperatures to 0C
; ===================== Custom settings ====================
M564 H0                                   	            	; Let the Jog buttons work blv: added to allow jog buttons

; ====================== Miscellaneous =====================
;M575 P1 S1 B57600                                       	; enable support for PanelDue
;M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" 			; set voltage thresholds and actions to run on power loss

;Duet 2 pinout-*=inverted
;bedheat * Bedheater
;e0heat * Hotend
;e1heat * NC
;exp.heater3 BLTouch S
;Duet 2 temperature inputs
;bedtemp Bed thermistor
;e0temp HE thermistor
;e1temp NC
;Duet 2 fan outputs
;fan0 MB Fan GND
;fan1 LY Fan GND
;fan2 HE Fan GND
;Endstop inputs
;xstop X Endstop C
;ystop Y Endstop C
;zstop NC
;e0stop Filament runout sensor C
;e1stop Off button C pin
;zprobe.in Z-
;zprobe.mod NC

hey,

I was using E0 with one of my printer heads but I want to add the other pin to my config to use the pin with another cable and another head. I checked the new cable in E0 it is working, I took out the cable from the e0 put it to the e1 and i left the e0 empty. I went to config tool add a new nozzle named e1temp and e1heat. created a config, I took the lines which are related with e1 and add them to my original config. but i cant see the new pin on dashboard, also i sent the m122 it says heater1 is on but says nothing about heater2 which is e1. how can i use both pins with different cables and heads. when i change the head ill leave the other cable on the pin but wont use it.

m122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.4.5 (2022-11-30 19:36:12) running on Duet Ethernet 1.02 or later + DueX5
Board ID: 08DGM-917DA-G4MSJ-6J9D6-3SJ6T-19R38
Used output buffers: 1 of 26 (13 max)
=== RTOS ===
Static ram: 23836
Dynamic ram: 70876 of which 60 recycled
Never used RAM 17308, free system stack 206 words
Tasks: NETWORK(ready,24.4%,225) HEAT(notifyWait,0.0%,333) Move(notifyWait,0.0%,363) DUEX(notifyWait,0.0%,24) MAIN(running,75.3%,438) IDLE(ready,0.3%,30), total 100.0%
Owned mutexes:
=== Platform ===
Last reset 00:03:50 ago, cause: software
Last software reset at 2023-09-06 16:29, reason: User, GCodes spinning, available RAM 17296, slot 0
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Step timer max interval 0
MCU temperature: min 33.3, current 34.5, max 34.7
Supply voltage: min 24.0, current 24.0, max 24.1, under voltage events: 0, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Events: 0 queued, 0 completed
Driver 0: standstill, SG min n/a
Driver 1: standstill, SG min n/a
Driver 2: standstill, SG min n/a
Driver 3: standstill, SG min n/a
Driver 4: standstill, SG min n/a
Driver 5: standstill, SG min n/a
Driver 6: standstill, SG min n/a
Driver 7: standstill, SG min n/a
Driver 8: standstill, SG min n/a
Driver 9: standstill, SG min n/a
Driver 10: 
Driver 11: 
Date/time: 2023-09-06 16:33:23
Cache data hit count 4294967295
Slowest loop: 11.07ms; fastest: 0.18ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 1.0ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, segments created 0, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters 0 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0
Heater 0 is on, I-accum = 0.0
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty
=== DueX ===
Read count 1, 0.26 reads/min
=== Network ===
Slowest loop: 13.13ms; fastest: 0.02ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0)
HTTP sessions: 1 of 8
Interface state active, link 100Mbps full duplex

my old config;

; Configuration file for Duet Ethernet (firmware version 3)
; executed by the firmware on start-up
;
; generated by Julian Zettl Feb 2022
; edited by Deniz and Tillman July 2023

; ================= General preferences ===================
G90                 ; send absolute coordinates...
M83                 ; ...but relative extruder moves
M550 P"BLV"         ; set printer name
M669 K1				; Select CoreXY mode


; ====================== Network ===========================
M552 S1                                       	; enable network
M552 P192.168.1.254								; set IP Address
M553 P255.255.255.0								; set Netmask
M554 P192.168.1.2								; Set default Gateway
M586 P0 S1                                    	; enable HTTP
M586 P1 S0                                  	; disable FTP
M586 P2 S0                                   	; disable Telnet

; ======================= Drives ===========================
M569 P0 S0                                      ; physical drive 0 goes backwards (A motor)
M569 P1 S0                                      ; physical drive 1 goes backwards (B motor)
M569 P2 S1                                      ; physical drive 2 goes forwards (alpha)
M569 P5 S0                                      ; physical drive 4 goes forwards (beta) 
M569 P6 S0 										; physical drive 6 goes forwards (gamma) 

M569 P3 S1                                      ; physical drive 3 goes forwards (E0 motor) 
;M569 P5 S1 										; physical drive 5 goes forwards (E1 motor) 
M584 X0 Y1 Z2:5:6 E3:4							; set drive mapping

; ===================== Drive Settings =====================
M350 X128 Y128 Z128:128:128 E128:128 I1			; configure microstepping with interpolation
M92  X1600 Y1600 Z12800:12800:12800 E3936:6400  ; steps per mm E1:800 E2:837
M566 X540 Y540  Z56:56:56 E480:480      		; maximum instantaneous speed changes mm/min
M203 X10000 Y10000 Z1800:1800:1800 E15000:15000	; maximum speeds (mm/s)
M201 X2000 Y2000 Z100:100:100 E1000:3000        ; set accelerations (mm/s^2)
M906 X1000 Y1000 Z800 E800 I50					; set motor currents (mA) and  idle %
M84 S120	                               	    ; Set idle timeout

; ================ Independent Z Leveleing =================
M671 X-170.24:170.24:0 Y-128.815:-128.815:130.75 S20	   	; leadscrew pivot point:

; ===================== Axis Limits ========================
M208 X-45 Y-36 Z0 S1                                      	; set axis min
M208 X270 Y270 Z200 S0                                  	; set axis max
;originally with 0,0 centered on bed:
;M208 X-152:150 Y-144:172

; ======================= Endstops =========================
M574 X1 S1 P"x_stop"   		; X min active high endstop switch
M574 Y2 S1 P"y_stop"   		; Y max active high endstop switch
M574 Z1 S2                  ; configure Z-probe endstop for low end on Z

; ======================== Z-Probe =========================
;M950

M558 P9 C"zprobe.in" H5 F120 T6000 ; Duet 2 WiFi/Ethernet, DueX2/5
M950 S0 C"duex.pwm1" ; Duet 2 WiFi/Ethernet + DueX2/5
;M307 H3 A-1 C-1 D-1 ; Disable heater 3 to free up PWM channel 1 on the Duex board.
;M558 P1 C"ZPROBE.IN" H5 F500 T1000	; Z Probe type=analog, pin, dive height+rate, travelspeed
;M280 P0 S90
G31 X27 Y58 Z1 P25
;G31 X0 Y0 Z0.2 P500					; Z Probe offset and trigger value
M557 X15:215 Y15:195 S60     		; define mesh grid

; ======================== Heaters =========================
;M305 P1 T100000 B4267 R4700		; old RRF2.x 
M301 H1 H2 P21.1 I0.816 D59.6  		;PID settings hotend from old config
M308 S1 P"e0temp" Y"thermistor" A"Hotend" T100000 B4267 R4700  	; extruder thermistor
M950 H1 C"e0heat" T1 	 								  		; link heater to sensor
M143 H1 S285		        									; temperature limit
M104 S0 
                                                     ; turn off  nozzle heater
M308 S0 P"bedtemp" Y"thermistor" A"Bed" T100000 B4267 R4700		; configure sensor 0 as thermistor on pin bedtemp
M950 H0 Q10 C"bedheat" T0                                   	; create bed heater output on bedheat and map it to sensor 0
M307 H0 A284.0 C843.8 D11.0 B0									; Heatbed PID
M140 H0 S0                                               		; map heated bed to heater 0
M143 H0 S100                                            		; set temperature limit for heater 0 to 120C

M308 S2 P"mcu-temp" Y"mcu-temp" A"Duet Board" 					; Configure MCU sensor

; ========================= Fans ===========================
M106 P0 S0.1 I0 F500 T45 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P1 S1 I0 F500 H1 T45 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on

M950 F0 C"fan0" Q250                	; create fan 1 on pin fan0 and set its frequency
M106 P0 C"hotend fan" T60 H1        	; P"fan1" C"displayname" T"triggervalue" H"heater1"

M950 F1 C"fan1"                
M106 P1 S100 

; ======================== Tools ===========================
M563 P0 S"FDM" D0 H1			; P"tool0" S"displayname" D"e0motor" H"heater1"
G10 P0 X0 Y0 Z0      			; set tool 0 axis offsets
G10 P0 R0 S0             		; set initial tool 0 active and standby temperatures to 0C

; ===================== Custom settings ====================
M564 H0                                   	            	; Let the Jog buttons work blv: added to allow jog buttons

; ====================== Miscellaneous =====================
;M575 P1 S1 B57600                                       	; enable support for PanelDue
;M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" 			; set voltage thresholds and actions to run on power loss

;Duet 2 pinout-*=inverted
;bedheat * Bedheater
;e0heat * Hotend
;e1heat * NC
;exp.heater3 BLTouch S
;Duet 2 temperature inputs
;bedtemp Bed thermistor
;e0temp HE thermistor
;e1temp NC
;Duet 2 fan outputs
;fan0 MB Fan GND
;fan1 LY Fan GND
;fan2 HE Fan GND
;Endstop inputs
;xstop X Endstop C
;ystop Y Endstop C
;zstop NC
;e0stop Filament runout sensor C
;e1stop Off button C pin
;zprobe.in Z-
;zprobe.mod NC

the lines that i took from config tool

M308 S2 P"e1temp" Y"thermistor" T100000 B4138  ; configure sensor 2 as thermistor on pin e1temp
M950 H2 C"e1heat" T2                           ; create nozzle heater output on e1heat and map it to sensor 2
M307 H2 B0 S1.00                               ; disable bang-bang mode for heater  and set PWM limit
M143 H2 S280                                   ; set temperature limit for heater 2 to 280C

@Phaedrux okay I found the problem the gateway number was changed and I set it with m554

@siladeniz I noticed that in the files config.g and config.json don't have same content. Is it should be like that?

@Phaedrux no because I don't want to use new config I just want to take the second heater lines from there and add to my config. Also while I am trying to update the documents which I got from config tool, I deleted www, firmware and sys files in sd card. and add the config tool generated www,firmware and sys files. later as I said previously it didn't work and I turned back to old files. I think I might delete something wrong I'll share the files with you can you check please?

or there is another option I can delete all the files in the sd card, I'll copy my config and macros. and I will download the latest firmware version and put it to the sd card. Does it work? I don't know if the other files can be arranged by user or just copy paste from the downloads thats why I don't know if I arranged them in some way.
here is the files:

www sys macros gcodes firmware

hey,
I have duet 2 ethernet I am using reprap 3.4.5
I wanted the use both hotend heater pins. firstly to check if the new cables are working or not I used the previously used pin which is e0. the hotend worked properly, so no problem with the cable. later I put the same cables to the other pin(e1) and leave e0 free. I changed the pin and heater number from config, but it didn't worked I could see the new created heater from DWC dashboard but the temprature was -273 C. so I went to config tool and add 1 more heater and create the new config. But unfortunately I didn't add the new part to my config I upload the new created system files via DWC. And I think it changed the config too, later I couldn't reach the DWC anymore. I checked the IP address from pronter face it was 0.0.0.0 and set the IP address to my previous one by m552 s0 p... and it settled but I still couldnt reach DWC. I took out the sd card and put it to my computer and delete the config and add the previous config but it doesn't work still. this is the previous config

; Configuration file for Duet Ethernet (firmware version 3)
; executed by the firmware on start-up
;
; generated by Julian Zettl Feb 2022
; edited by Deniz and Tillman July 2023

; ================= General preferences ===================
G90                 ; send absolute coordinates...
M83                 ; ...but relative extruder moves
M550 P"BLV"         ; set printer name
M669 K1				; Select CoreXY mode

;=================== Calling Macro =====================
;M98 P/macros/print_start.g 
; ====================== Network ===========================
M552 S1                                       	; enable network
M552 P192.168.1.254								; set IP Address
M553 P255.255.255.0								; set Netmask
M554 P192.168.1.0								; Set default Gateway
M586 P0 S1                                    	; enable HTTP
M586 P1 S0                                  	; disable FTP
M586 P2 S0                                   	; disable Telnet

; ======================= Drives ===========================
M569 P0 S0                                      ; physical drive 0 goes backwards (A motor)
M569 P1 S0                                      ; physical drive 1 goes backwards (B motor)
M569 P2 S1                                      ; physical drive 2 goes forwards (alpha)
M569 P5 S0                                      ; physical drive 4 goes forwards (beta) 
M569 P6 S0 										; physical drive 6 goes forwards (gamma) 

M569 P3 S1                                      ; physical drive 3 goes forwards (E0 motor) 
;M569 P5 S1 										; physical drive 5 goes forwards (E1 motor) 
M584 X0 Y1 Z2:5:6 E3:4							; set drive mapping

; ===================== Drive Settings =====================
M350 X128 Y128 Z128:128:128 E128:128 I1			; configure microstepping with interpolation
M92  X1600 Y1600 Z12800:12800:12800 E3936:6400  ; steps per mm E1:800 E2:837
M566 X540 Y540  Z56:56:56 E480:480      		; maximum instantaneous speed changes mm/min
M203 X10000 Y10000 Z1800:1800:1800 E15000:15000	; maximum speeds (mm/s)
M201 X2000 Y2000 Z100:100:100 E1000:3000        ; set accelerations (mm/s^2)
M906 X1000 Y1000 Z800 E800 I50					; set motor currents (mA) and  idle %
M84 S120	                               	    ; Set idle timeout

; ================ Independent Z Leveleing =================
M671 X-170.24:170.24:0 Y-128.815:-128.815:130.75 S20	   	; leadscrew pivot point:

; ===================== Axis Limits ========================
M208 X-45 Y-36 Z0 S1                                      	; set axis min
M208 X270 Y270 Z200 S0                                  	; set axis max
;originally with 0,0 centered on bed:
;M208 X-152:150 Y-144:172

; ======================= Endstops =========================
M574 X1 S1 P"x_stop"   		; X min active high endstop switch
M574 Y2 S1 P"y_stop"   		; Y max active high endstop switch
M574 Z1 S2                  ; configure Z-probe endstop for low end on Z

; ======================== Z-Probe =========================
;M950

M558 P9 C"zprobe.in" H5 F120 T6000 ; Duet 2 WiFi/Ethernet, DueX2/5
M950 S0 C"duex.pwm1" ; Duet 2 WiFi/Ethernet + DueX2/5
;M307 H3 A-1 C-1 D-1 ; Disable heater 3 to free up PWM channel 1 on the Duex board.
;M558 P1 C"ZPROBE.IN" H5 F500 T1000	; Z Probe type=analog, pin, dive height+rate, travelspeed
;M280 P0 S90
G31 X27 Y58 Z1 P25
;G31 X0 Y0 Z0.2 P500					; Z Probe offset and trigger value
M557 X15:215 Y15:195 S60     		; define mesh grid

; ======================== Heaters =========================
;M305 P1 T100000 B4267 R4700		; old RRF2.x 
M301 H1 P21.1 I0.816 D59.6  		;PID settings hotend from old config
M308 S1 P"e0temp" Y"thermistor" A"Hotend" T100000 B4267 R4700  	; extruder thermistor
M950 H1 C"e0heat" T1 	 								  		; link heater to sensor
M143 H1 S285		        									; temperature limit
M104 S0                                                          ; turn off  nozzle heater
M308 S0 P"bedtemp" Y"thermistor" A"Bed" T100000 B4267 R4700		; configure sensor 0 as thermistor on pin bedtemp
M950 H0 Q10 C"bedheat" T0                                   	; create bed heater output on bedheat and map it to sensor 0
M307 H0 A284.0 C843.8 D11.0 B0									; Heatbed PID
M140 H0 S0                                               		; map heated bed to heater 0
M143 H0 S100                                            		; set temperature limit for heater 0 to 120C

M308 S2 P"mcu-temp" Y"mcu-temp" A"Duet Board" 					; Configure MCU sensor

; ========================= Fans ===========================
M106 P0 S0.1 I0 F500 T45 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P1 S1 I0 F500 H1 T45 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on

M950 F0 C"fan0" Q250                	; create fan 1 on pin fan0 and set its frequency
M106 P0 C"hotend fan" T60 H1        	; P"fan1" C"displayname" T"triggervalue" H"heater1"

M950 F1 C"fan1"                
M106 P1 S100 

; ======================== Tools ===========================
M563 P0 S"FDM" D0 H1			; P"tool0" S"displayname" D"e0motor" H"heater1"
G10 P0 X0 Y0 Z0      			; set tool 0 axis offsets
G10 P0 R0 S0             		; set initial tool 0 active and standby temperatures to 0C

; ===================== Custom settings ====================
M564 H0                                   	            	; Let the Jog buttons work blv: added to allow jog buttons

; ====================== Miscellaneous =====================
;M575 P1 S1 B57600                                       	; enable support for PanelDue
;M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" 			; set voltage thresholds and actions to run on power loss

;Duet 2 pinout-*=inverted
;bedheat * Bedheater
;e0heat * Hotend
;e1heat * NC
;exp.heater3 BLTouch S
;Duet 2 temperature inputs
;bedtemp Bed thermistor
;e0temp HE thermistor
;e1temp NC
;Duet 2 fan outputs
;fan0 MB Fan GND
;fan1 LY Fan GND
;fan2 HE Fan GND
;Endstop inputs
;xstop X Endstop C
;ystop Y Endstop C
;zstop NC
;e0stop Filament runout sensor C
;e1stop Off button C pin
;zprobe.in Z-
;zprobe.mod NC

this is the config generated by config tool

; Configuration file for Duet WiFi (firmware version 3.3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.3.16 on Thu Aug 31 2023 10:46:37 GMT+0200 (Central European Summer Time)

; General preferences
G90                                            ; send absolute coordinates...
M83                                            ; ...but relative extruder moves
M550 P"BLV Cube"                               ; set printer name

; Network
M552 S1                                        ; enable network
M586 P0 S1                                     ; enable HTTP
M586 P1 S0                                     ; disable FTP
M586 P2 S0                                     ; disable Telnet

; Drives
M569 P0 S1                                     ; physical drive 0 goes forwards
M569 P1 S1                                     ; physical drive 1 goes forwards
M569 P2 S1                                     ; physical drive 2 goes forwards
M569 P3 S1                                     ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3                               ; set drive mapping
M350 X16 Y16 Z16 E16 I1                        ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z400.00 E420.00              ; set steps per mm
M566 X900.00 Y900.00 Z60.00 E120.00            ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 E1200.00        ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00 E250.00            ; set accelerations (mm/s^2)
M906 X800 Y800 Z800 E800 I30                   ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                        ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1                               ; set axis minima
M208 X230 Y210 Z200 S0                         ; set axis maxima

; Endstops
M574 X1 S1 P"xstop"                            ; configure switch-type (e.g. microswitch) endstop for low end on X via pin xstop
M574 Y1 S1 P"ystop"                            ; configure switch-type (e.g. microswitch) endstop for low end on Y via pin ystop
M574 Z1 S2                                     ; configure Z-probe endstop for low end on Z

; Z-Probe
M558 P1 C"zprobe.in" H5 F120 T6000             ; set Z probe type to unmodulated and the dive height + speeds
G31 P500 X0 Y0 Z2.5                            ; set Z probe trigger value, offset and trigger height
M557 X15:215 Y15:195 S20                       ; define mesh grid

; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0                          ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B1 S1.00                               ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0                                        ; map heated bed to heater 0
M143 H0 S120                                   ; set temperature limit for heater 0 to 120C
M308 S1 P"e1temp" Y"thermistor" T100000 B4138  ; configure sensor 1 as thermistor on pin e1temp
M950 H1 C"e1heat" T1                           ; create nozzle heater output on e1heat and map it to sensor 1
M307 H1 B0 S1.00                               ; disable bang-bang mode for heater  and set PWM limit
M143 H1 S280                                   ; set temperature limit for heater 1 to 280C

; Fans
M950 F0 C"fan0" Q500                           ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1                                 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500                           ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T45                              ; set fan 1 value. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0                               ; define tool 0
G10 P0 X0 Y0 Z0                                ; set tool 0 axis offsets
G10 P0 R0 S0                                   ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M501                                           ; load saved parameters from non-volatile memory

@siladeniz also when it worked it send an error: Warning: Driver 1 warning: phase A may be disconnected, phase B may be disconnected

@Phaedrux I did what you wanted and it worked for once now I cant reach the BLV, and I checked the IP address from pronter face it is correct

@deckingman because my macros were working before I got SD card problem, and the endstops were enable.

print_start.g

and here is the start macro, as you can see everything is defined

@deckingman oh it was for prepare the printer to print like heating the bed, bed leveling etc. it is not related with my problem

@Phaedrux I am sending the m119, it says no endstop for every endstop.
but when I touch the endstops the lights go on and off.

I touch the y endstop and send m119 again it is still no endstop. what is the problem?

@Phaedrux there was no problem with the endstops before I had a sd card error, now the printer doesnt see the endstops but I didnt change anything and it was working.

Also I delete the config.g from sd card and add it back, now I dont have the error "Your Duet rejected the HTTP request: page not found
Check that the SD card is mounted and has the correct files in its /www folder"

@Phaedrux M98 P"config.g"
Error: Failed to enable endstops