Posts made by Skater

Thank you for all your help

Here is the best I can get

Thank You
That is correct. The E1 heater is also lit

When I remove the jumper from the INT 5v EN the heater will turn off. Does that help at all in the diagnostics? I would like to get this issue taken care of

Motors, endstops, Hotend and a BLTouch

I have looked over the board and can find no damage what so ever. Since I blew out a mosfet on a previos board I know what it looks like.

Thanks

Just hooked up a new board and the heatbed is always on. I have started the board without the SD card to rule out a config problem
Here is all the info I hope you need.

RepRapFirmware for Duet 2 WiFi/Ethernet FIRMWARE_VERSION: 2.05.1
ELECTRONICS: Duet WiFi 1.02 or later
FIRMWARE_DATE: 2020-02-09b1

G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"FT-5" ; set printer name

; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet

; Drives
M569 P0 S1 ; physical drive 0 goes forwards
M569 P1 S1 ; physical drive 1 goes forwards
M569 P2 S1 ; physical drive 2 goes forwards
M569 P3 S1 ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X32 Y32 Z32 E32 I1 ; configure microstepping without interpolation
M92 X161.61 Y160.00 Z797.26 E832.28 ; set steps per mm
M566 X900.00 Y900.00 Z12.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 E1200.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00 E250.00 ; set accelerations (mm/s^2)
M906 X1100 Y1200 Z1200 E1000 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X300 Y300 Z400 S0 ; set axis maxima

; Endstops
M574 X1 Y1 S1 ; set active high endstops
M574 Z1 S2 ; set endstops controlled by probe

; Z-Probe
M307 H7 A-1 C-1 D-1;
M558 P9 F100 H5 R0.2 T6000 A5 B1;
G31 P25 X20 Y0 Z0.0 ; Z probe trigger value, offset in relation to nozzle. And trigger height adjustment
M557 X25:285 Y15:285 S20 ; Define mesh grid

; Heaters
M305 P0 T1000000 ; set thermistor + ADC parameters for heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M305 P1 T500000 B4723 C1.196220e-7 ; Set thermistor + ADC parameters for heater 1
M143 H1 S280 ;set temperature limit for heater 1 to 280C
;
; Fans
M106 P0 S0 I0 F500 H-1 ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H-1 ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned off

; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

Thanks in advance

Board is Duet Wifi 1.04
Firmware: RepRapFirmware for Duet 2 WiFi/Ethernet 2.05.1 (2020-02-09b1)
Duet WiFi Server Version: 1.23

The issue is the input for the probe is always high. So when the probe is started it stops right away.
The probe input is high even when there is no probe attached. I did not have this problem before I added the new thermistor.

Thank you for helping so far

Config.g
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"FT-5" ; set printer name

; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet

; Drives
M569 P0 S1 ; physical drive 0 goes forwards
M569 P1 S1 ; physical drive 1 goes forwards
M569 P2 S0 ; physical drive 2 goes forwards
M569 P3 S1 ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X32 Y32 Z32 E32 I1 ; configure microstepping without interpolation
M92 X161.61 Y160.00 Z797.26 E832.28 ; set steps per mm
M566 X900.00 Y900.00 Z12.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 E1200.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00 E250.00 ; set accelerations (mm/s^2)
M906 X1100 Y1200 Z1200 E1000 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X300 Y300 Z400 S0 ; set axis maxima

; Endstops
M574 X1 Y1 S1 ; set active high endstops
M574 Z1 S2 ; set endstops controlled by probe

; Z-Probe
M307 H7 A-1 C-1 D-1;
M558 P9 F100 H5 R0.2 T6000 A5 B1 ;
G31 P25 X20 Y0 Z0.0 ; Z probe trigger value, offset in relation to nozzle. And trigger height adjustment
M557 X25:285 Y15:285 S20 ; Define mesh grid

; Heaters
M305 P0 T100000 B4138 R4700 ; set thermistor + ADC parameters for heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M305 P1 T100000 B4267 R4700 ; Set thermistor + ADC parameters for heater 1
M143 H1 S280 ; set temperature limit for heater 1 to 280C

; Fans
M106 P0 S0 I0 F500 H-1 ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H-1 ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned off

; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

Homeall.g
G91 ; relative positioning
G1 H2 Z5 F6000 ; lift Z relative to current position
G1 H1 X-305 Y-305 F1800 ; move quickly to X and Y axis endstops and stop there (first pass)
G1 H2 X5 Y5 F6000 ; go back a few mm
G1 H1 X-305 Y-305 F360 ; move slowly to X and Y axis endstops once more (second pass)
G90 ; absolute positioning
G1 X40 Y15 F6000 ; go to first bed probe point and home Z
G30 ; home Z by probing the bed

Homez.g
G91 ; relative positioning
G1 H2 Z5 F6000 ; lift Z relative to current position
G90 ; absolute positioning
G1 X40 Y15 F6000 ; go to first probe point
G30 ; home Z by probing the bed

Thanks

I need help setting up my BLTouch 3.1
When I add the code M558 P9 F100 H5 R0.2 T6000 A5 B1 it sets the Z-probe to 1000. When i add the I1 to invert the signal it goes to 0. All the actions, drop pin, raise pin, test, and reset all work. The issue is when I go to home the z-axis, it never triggers. I set it up using BeTrue3ds set up and changed P5 to P9.
Let me also add that this issue started when I added a Mosquito hotend and thermister.
Any help would be appreciated.

Nope, Have a point there

Bed is not moving at all except for lowering to change level. M122 says Bed compensation in use: mesh

I have the map loaded. Run the G29 S1. My Z steppers should move a bit shouldn't they? They are not, any ideas

So if I have the map just issue a G29 S1 in my start up gcode and the map will load?

I used the M122 and there is nothing for bed probes heights. When I click the view map I see the map of my bed. I must be missing a step somewhere to save the probe data. Any idea what it is?

Using a bltouch. After the grid map is set up, when a G29 command is issued is the map loaded so it does not have to do a grid map again?

Just used P"". Did the trick

Just network ssid

Hi all first post here
I have been trying to upgrade the firmware to 1.19. After everything is flashed I enter M552 S0 and get a wifi module is idle. I then try to assign my network using M587 S"SSID", I know it's not SSID. But I get back M587 bad parameter. What's going on? How do I fix it

Thanks
Andy