Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login
    1. Home
    2. Sytac072
    • Profile
    • Following 1
    • Followers 0
    • Topics 4
    • Posts 18
    • Best 0
    • Controversial 0
    • Groups 0

    Sytac072

    @Sytac072

    0
    Reputation
    1
    Profile views
    18
    Posts
    0
    Followers
    1
    Following
    Joined Last Online

    Sytac072 Unfollow Follow

    Latest posts made by Sytac072

    • RE: Software package 3.3beta3 released

      @stephen6309 said in Software package 3.3beta3 released:

      @paulhew If you are using PrusaSlicer you need to add to the Before layer change G-Code: ;LAYER:[layer_num]
      It's under Custom G-Code in Printer Settings.

      Hi, I have the same problem using S3D 4.1.2

      posted in Beta Firmware
      Sytac072undefined
      Sytac072
    • RE: Extruder disappeared from DWC

      @droftarts Thank you very much for your quick reply and tip. This was the issue. I removed the F-1 and the extruder came back.

      posted in Beta Firmware
      Sytac072undefined
      Sytac072
    • Extruder disappeared from DWC

      Hello, I have an issue...
      I own a duet2 wifi and yesterday I tried to upgrade from RRF 3.2.2 to RRF 3.3 b3 and at this point, the extruder disappeared from the DWC 3.3 b3 as well as from the paneldue.

      config.g

      Any idea?

      posted in Beta Firmware
      Sytac072undefined
      Sytac072
    • RE: Software package 3.3beta3 released

      @stephen6309 Yes, I did it... The config.g is the same I was using with RRF 3.2.2. I reinstalled it and the printer was working again.

      posted in Beta Firmware
      Sytac072undefined
      Sytac072
    • RE: Software package 3.3beta3 released

      @stephen6309 Thank you very much for your tip. I have a duet2 Wifi. I am not sure if your settings may also work on mine.

      posted in Beta Firmware
      Sytac072undefined
      Sytac072
    • RE: Software package 3.3beta3 released

      Hello... I have tried to upgrade my Tevo delta today from RRF 3.2.2 to 3.3 beta 3 but after the upgrade, the extruder disappeared from the DWC and from the paneldue.

      This is how the motors are configured:

      M584 X0 Y1 Z2 E3 ; set drive mapping

      I don't what is wrong.

      posted in Beta Firmware
      Sytac072undefined
      Sytac072
    • RE: Tevo Little Monster calibration issues with RRF 3.1.1

      @jay_s_uk

      Yes, you are right. This is already a mistake but the homing process works correctly anyway.

      posted in Tuning and tweaking
      Sytac072undefined
      Sytac072
    • RE: Tevo Little Monster calibration issues with RRF 3.1.1

      @Veti
      ; config-override.g file generated in response to M500 at 2020-09-17 13:01
      ; This is a system-generated file - do not edit
      ; Delta parameters
      M665 L407.671:407.671:407.671 R167.529 H473.244 B160.0 X-0.109 Y-0.362 Z0.000
      M666 X1.320 Y0.069 Z-1.390 A0.07 B-0.19
      ; Heater model parameters
      M307 H0 A171.3 C936.8 D0.9 S1.00 V23.9 B0
      M307 H1 A294.8 C253.4 D3.1 S1.00 V23.7 B0
      ; Workplace coordinates
      G10 L2 P1 X0.00 Y0.00 Z0.00
      G10 L2 P2 X0.00 Y0.00 Z0.00
      G10 L2 P3 X0.00 Y0.00 Z0.00
      G10 L2 P4 X0.00 Y0.00 Z0.00
      G10 L2 P5 X0.00 Y0.00 Z0.00
      G10 L2 P6 X0.00 Y0.00 Z0.00
      G10 L2 P7 X0.00 Y0.00 Z0.00
      G10 L2 P8 X0.00 Y0.00 Z0.00
      G10 L2 P9 X0.00 Y0.00 Z0.00

      posted in Tuning and tweaking
      Sytac072undefined
      Sytac072
    • RE: Tevo Little Monster calibration issues with RRF 3.1.1

      ; Configuration file for Duet WiFi (firmware version 3)
      ; executed by the firmware on start-up
      ;
      ; generated by RepRapFirmware Configuration Tool v2.1.4 on Mon Jan 06 2020 13:06:19 GMT+0100 (Ora standard dell’Europa centrale)

      ; General preferences
      G28 ; Home all axes
      M111 S0 ; Debugging off
      G21 ; Works in millimiters
      G90 ; send absolute coordinates...
      M83 ; ...but relative extruder moves
      M555 P1 ; Set firmware compatibility to look like RepRap Firmware
      M665 L400.25:400.25:400.25 R165 B160 H485 ; Set delta radius, diagonal rod length, printable radius and homed height (With extra glass 13/07/2020)
      M666 X0 Y0 Z0 ; put your endstop adjustments here, or let auto calibration find them
      M575 P1 B57600 S1 ; set paneldue communication parameters

      ; Network

      M550 P"TEVO Little Monster" ; Set machine name
      M552 S1 ; Enable network

      M586 P0 S1 ; Enable HTTP
      M586 P1 S1 ; Enable FTP
      M586 P2 S0 ; Disable Telnet

      ; Drives
      M569 P0 S0 ; physical drive 0 goes backwards
      M569 P1 S0 ; physical drive 1 goes backwards
      M569 P2 S0 ; physical drive 2 goes backwards
      M569 P3 S0 ; physical drive 3 goes backwards
      M584 X0 Y1 Z2 E3 ; set drive mapping
      M579 X1.00806 Y1.007252 Z1.0040 ; Scale parameter for axes X, Y and Z calculated on 16/05/2020
      M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
      M92 X160.00 Y160.00 Z160.00 E819.338 ; set steps per mm
      M566 X1200.00 Y1200.00 Z1200.00 E1200.00 ; set maximum instantaneous speed changes (mm/min)
      M203 X18000.00 Y18000.00 Z18000.00 E1200.00 ; set maximum speeds (mm/min)
      M201 X1000.00 Y1000.00 Z1000.00 E1000.00 ; set accelerations (mm/s^2)
      M906 X1250 Y1250 Z1250 E1200 I30 ; set motor currents (mA) and motor idle factor in per cent
      M84 S30 ; Set idle timeout

      ; Axis Limits
      M208 Z0 S1 ; set minimum Z

      ; Endstops
      M574 X1 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop
      M574 Y1 S1 P"ystop" ; configure active-high endstop for low end on Y via pin ystop
      M574 Z1 S1 P"zstop" ; configure active-high endstop for low end on Z via pin zstop

      ; Z-Probe
      M558 P8 R0.8 C"zprobe.in+zprobe.mod" H5 A5 F1200 T6000 ; set Z probe type to effector and the dive height + speeds (New setting from 15/05/2020)
      ;M558 P5 R0.4 C"zprobe.in+zprobe.mod" H1 F1200 T6000 ; set Z probe type to effector and the dive height + speeds (New setting from 10/01/2020)
      ;M558 P5 R0.4 C"zprobe.in+zprobe.mod" H5 F1200 T6000 ; set Z probe type to effector and the dive height + speeds (Original setting)
      G31 P500 X0 Y0 Z-0.152 ; set Z probe trigger value, offset and trigger height
      M557 R150 S15 ; define mesh grid (New setting from the old config.g)
      ;M557 R85 S15 ; define mesh grid (Original setting from configurator)

      ; Heaters
      ; Reference page : https://duet3d.dozuki.com/Wiki/Connecting_thermistors_or_PT1000_temperature_sensors
      M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 R4700 A"Piatto" ; configure sensor 0 as thermistor on pin bedtemp
      M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
      M140 H0 ; define and create the bed heater (set on 13/05/2020, needed with RRF 3)
      M143 H0 S120 ; set temperature limit for heater 0 to 120C
      M307 H0 B0 S1.00 ; disable bang-bang mode for the nozzle heater and set PWM limit
      M308 S1 P"e0temp" Y"thermistor" T100000 B4725 R4375 C7.06e-8 A"Estrusore"; configure sensor 1 as thermistor on pin e0temp
      M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
      M143 H1 S280 ; set temperature limit for heater 1 to 280C
      M307 H1 B0 S1.00 ; disable bang-bang mode for the nozzle heater and set PWM limit

      ; Fans
      M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
      M106 P0 C"Part cooling fan" S0 H-1 ; set fan 0 name and value. Thermostatic control is turned off
      M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
      M106 P1 C"Hotend fan" S1 H1 T45 ; set fan 1 name and value. Thermostatic control is turned on

      ; Tools
      M563 P0 D0 H1 F-1 ; define tool 0
      G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
      G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

      ; Filament run-out sensor
      M591 D0 P2 C3 S1 ; Filament run-out sensor Input high when filament is in

      ; Automatic power saving
      M911 S22 R23 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; Set voltage thresholds and actions to run on power loss

      ; Miscellaneus
      M375 ; Load the grid probing mesh
      M501 ; read stored parameters from config override

      posted in Tuning and tweaking
      Sytac072undefined
      Sytac072
    • Tevo Little Monster calibration issues with RRF 3.1.1

      Hi everyone. I own a Tevo Little Monster which I have upgraded with Duet2 WiFi, magnetic rods and Smart Effector.
      I have used the printer for a long time with RRF firmware until the latest one which was 2.05.1 and the printer works perfectly, without any trouble. Then I tried to upgrade to RRF 3.1.1 (doing the needed changes to the config files).
      At this point, I started to have troubles with the Z offset, which was always to be calibrated at every startup of the printer, as well as the mesh calibration, which is not working.
      Even during the printing process, it's difficult to have a good result, then I have reinstalled the previous one (2.05.1) and everything went back to normal.
      Anyone has any idea?

      posted in Tuning and tweaking
      Sytac072undefined
      Sytac072